Search Documents

By P. Henning

Rock fall accidents continue to be the main cause of fatal and serious injuries in the mining industry. Although there has been an improvement in the FOG (falls of ground) related fatal and serious injuries over the past few years, the rate is still too high. New technology has made it possible to reduce this rate significantly. FOG accidents imply failure of the support system or the design of the support system in use. In this paper we deal with the latest technology available to assist the mines to reduce the rates of FOG related injuries and fatalities.

Jan 1, 2010

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By S. Soren, K. Deo Mehta, G. Jha

The paper aims to find a sustainable sintering process through cleaner means, in order to achieve the desired outputs with zero environmental impact. At present, sintering has no control over its environmental impacts. These impacts occur when fossil fuels such as coal and coke are used in metallurgical sintering. These fossil fuels are undoubtedly effective in their assigned reducing task, but simultaneously emit about 220 kg of GHGs (greenhouse gases) per tonne of sinter produced. The current attempt has focused on reducing these emission levels by switching from coke to a renewable fuel source such as biomass. Biomass is a cleaner fuel source with a significantly lower emission footprint compared to coke. In the experimental campaign, sawdust and wood-charcoal were used in substitution for coke. Experiments were designed in a progressing substitution to obtain the maximum substitution ability without compromising the sinter properties. Sawdust as raw biomass source optimally substituted 10% of coke. The substitution levels were remarkably higher (30%) for wood charcoal due to its low moisture and high calorific values. A fuel blend with 30% biomass and remaining coke succeeded in producing a sinter with acceptable quality indices. Sinters prepared with or without biomass contribution shared an identical phase transformation and microstructures. In order to to maintain consistency in the process, every effort was made to maintain all operational and process parameters identically, except for the fuelling framework. Keywords: Sintering, sustainable, biomass, GHGs, fuel substitution

Jan 1, 2020

By B. P. von der Heyden, T. Blenkinsop, A. Mamuse

Zimbabwe hosts a varied array of coloured gemstones. With the exception of emerald deposits and several world-class pegmatites, few of the gemstone occurrences have received detailed attention from the scientific or mineral exploration communities. In the present contribution we summarize the status of knowledge of the gemstone deposits and occurrences in Zimbabwe, paying particular attention to the geological settings in which they were formed. Synthesis of this regional geological approach reveals that there may be significant exploration potential for further gemstone occurrences, particularly in the extensive pegmatite fields and in Al-enriched orogenic belts that have undergone greenschist to granulite facies metamorphism. Further socio-economic and developmental initiatives will aid in optimizing the value generation from this important sub-sector.

Feb 12, 2024

By B. McFadzean, S. Pikinini, C. T. O’ Connor

Sperrylite (PtAs₂) comprises about 21% of the platinum group minerals (PGMs) in the Platreef ore and regularly reports to the tailings due to its poor floatability. Hence, improving its recovery will be of great economic value to the South African PGM industry. The reasons for its poor floatability are not yet clear. This paper seeks to understand the interactions occurring between PtAs₂ and common thiol collectors, viz. potassium normal butyl xanthate (PNBX), sodium normal dibutyl dithiophosphate (SNBDTP) and sodium normal mono butyl dithiocarbamate (SNBDTC). By understanding its interactions with these collectors, it is hypothesised that it will be possible to suggest ligands that may help improve the floatability of sperrylite. Mineral-collector interactions were studied by determining the molar energy of interaction using isothermal titration calorimetry and electrochemical techniques. The hydrophobicity of the mineral before and after adsorption of the collectors was determined by heat of immersion and its flotation response determined by microflotation tests. Microflotation tests using synthetic sperrylite at pH 9 showed low collectorless recovery of 34.8% and after adding the equivalent of one pseudo-monolayer of the PNBX collector, the recovery of 32.5% was obtained. Moreover, the addition of up to three pseudo-monolayers coverage of PNBX did not result in any increase in flotation recovery. A small recovery improvement was noted when synthetic plant water with the ionic strength of 0.0484 mol/L was used, but this did not hold for all collectors, with SNBDTP exhibiting higher recoveries in distilled water. Keywords: Sperrylite; flotation; recovery; adsorption energy; collectors; 2SPW (synthetic plant water)

Jan 1, 2020

By H. Matsuoka, M. Kawata, K. Mitsuhashi, C. Tokoro, T. Kato

Copper sulfide minerals generally have high floatability, but their floatability decreases when surfaces are oxidised under some conditions. Sodium hydrosulfide, NaHS, is known both as an activator and as a depressant for copper minerals. NaHS at low concentrations activates copper oxides by sulfurising surfaces, but at high concentrations depresses copper sulfides by interfering with the adsorption of collectors. In this paper, we applied NaHS to activate oxidised chalcocite and bornite and focused on the conditions of NaHS treatments such as dosages and pH, and the effect of these conditions on the floatability of those minerals. The pure minerals treated with NaHS were analysed using zeta potential analyser and X-ray photoelectron spectroscopy. Analyses indicated that the reactions of NaHS and the products on the mineral surfaces after the reactions (i.e. oxidation, pH change) depended on whether NaHS reacted with copper or iron, and the reactions between NaHS and iron depend on NaHS concentration and pH. Flotation tests using a small column cell were performed with a single pure mineral, and using a Denver-type flotation machine with a copper sulfide ore. The results of each flotation test were utilised to clarify the floatability. The relation between flotation behaviours and analysis results were also discussed. Keywords: Chalcocite, bornite, NaHS activation, flotation, floatability

Jan 1, 2020

By Z. Leng

"After detonation of the explosive, the final blast-induced damage area around the blast-hole falls into three categories, namely crushed zone, fractured zone, and elastic deformation zone. This paper presents a modified model to calculate the size of crushed zone around a blast-hole in drill-and-blast, with the hoop compressive stress and cavity expansion effect taken into account. The material in the crushed zone was assumed to be a granular medium without cohesion, but with internal friction. On this basis, the formula for crushing zone radius was derived. The proposed approach was verified with tests reported in the literature and the simulated results from SPH-FEM coupled models. A full statistical analysis was also carried out, and the predicted values were found to be in better agreement with the test results compared with other models. A sensitivity analysis of the modified model showed that the size of the blast-induced damage area is mainly affected by the following factors: rock mass properties, in situ stress, and borehole pressure. In particular, the roles of borehole pressure and in situ stress are discussed. Finally, suggestions are made on how the size of the crushing zones can be decreased. IntroductionOver the past decades, drill-and-blast has become the most commonly used technology in rock excavation. It is well known that in rock mass fragmentation with explosives, the annular rocks around the blast-hole are converted into fines. The formation of these fines consumes a significant part of the energy of the detonation, which in general is ignored in the determination of the efficiency of detonation (Glatolenkov and Ivanov, 1992; Furtney et al., 2012). Many studies show that only 20–30% of the total explosive energy is effectively used in fragmenting the rock, and up to 50% of the energy generated by conventional charges is wasted in overcrushing of the crushed zone and the inner part of the fractured zone (Ouchterlony et al., 2004; Sanchidrian et al., 2007). How to control the crushed zone to enhance the effective utilization of explosive energy, reducing the unit explosive consumption and the engineering cost, is therefore of great significance."

Jan 1, 2016

By N. Mangadoddy, M. Padhi

The simulation of multi-component classification with modified viscosity model is the key focus in the current study. The classification of the ores using hydrocyclone is a renowned process and has a convoluted flow separation phenomenon. The highly turbulent flow inside hydrocyclone depends on the operating and design parameters apart from the feed mixture. Slurry viscosity also plays a dominant role in the classification of solid particles under the centrifugal settling action. A heterogeneous mixture with different components would result in different settling and rheological behaviour of particles’ suspension in the water medium. The newly proposed multi-component viscosity model (Mandakini et al. 2020) is implemented as a user-defined function to define the material property during the CFD study of the mixture rheology inside hydrocyclone classifier. The multiphase and turbulence model is solved using the modified Algebraic Slip Model and Large Eddy Simulation model. A comparison of the predicted component performance curves is evaluated with and without the corrected viscosity model. The density and size effect on the particle phase distribution inside the classifier are compared, where the misplacements of the finer particles are carefully assessed. Validation of the component classification in hydrocyclone with the laboratory experiments found a close agreement with the rheology based CFD data. Keywords: Dual-component, multi-component viscosity model, double-gap rheometer, computational fluid dynamics, high solids concentration

Jan 1, 2020

By G. B. Abaka-Wood, J. Addai-Mensah, W. Skinner

Recently, coal fly ash has become a potential candidate as a secondary resource of rare earth elements (REE). In this investigation, we studied the recovery of REE from fly ash from a commercial power plant. The specific aim was to assess the technical feasibility of recovering REE from the coal fly ash using conventional preconcentration methods, including gravity separation, magnetic separation, and froth flotation. The experimental results revealed that flotation achieved major gains in REE recovery and upgrading. However, during gravity and wet magnetic separation tests, the bulk of REE reported to the tailings. The results showed significant variations in the performance of the various beneficiation methods investigated. This study has confirmed that existing physical separation methods could be used to recover REE from coal fly ash prior to hydrometallurgical and pyrometallurgical processing, although some challenges persist.

Jan 2, 2022

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By S-J. Park

When evaluating mining investment opportunities, one should consider the risks associated with mineral exploration and development. These are commonly classified as technical, economic, and political risks, and are accounted for in the investment decision by changing the discount rate. Thus, a company may use different discount rates associated with varying risks in order to compensate for the variability of success. The discount rate has a tremendous effect on the economic evaluation of mineral projects. Even when all other factors used as inputs for calculating the NPV (net present value) are equal, the project under consideration may be accepted or rejected depending upon the discount rate. Determining a realistic discount rate for a given project is therefore the most difficult and important aspect of cash flow analysis. It should be determined with the consideration of proper technical, economic, and political conditions surrounding the specific project undergoing economic evaluation. One key problem for determining the appropriate discount rate is that it typically depends more on subjective perception of the degree of risk or other experience factors than on a systematic approach. Thus, this study aims to identify, analyse, and document the type, role, and impact of risk factors influencing the determination of discount rates, and then to determine discount rate by using the aforementioned factors.

Jan 1, 2011

By V. V. Getman, V. A. Chanturiya, T. N. Matveeva

Most of the Au and PGM ores in Russia are characterised by a thin mineral impregnation of noble metals in sulfide minerals, and a large variety of mineral forms that lead to high loss of precious metals with fine fractions during flotation. In modern flotation technology, the rational choice of reagents is one of the main trends for selective separation of minerals and effective metals recovery. New data on the selectivity of the thermo-sensitive polymer with specific functional groups (TMPPh) as a flocculant and collector of Au and Pt fine fractions are available. The selective modified collector (DEDTCm) for the recovery of Au and Pt from complex ores is discussed in this paper. Scanning electronic microscopy (SEAM), laser SIM and AFM microscopy, UV and IR spectroscopy were applied to study the adsorbed layer of new reagents on the mineral surface. Flotation tests of TMPPh on the gold-bearing ore of the Olimpiada deposit showed an increase in Au extraction and Au content in the concentrate of the rougher flotation. Using a combination of reagents TMPPh and ButX, the quality of the Au and Pt concentrates increased in 1.7 time with an increase in recovery up to 15 % compared with the traditional reagent mode. Testing of TMPPh polymers in flotation of Pt-Cu-Ni ore at Norilsk Nickel has shown the ability to obtain a concentrate with a higher Pt content. Recovery of platinum is 17% higher than recovery in an experiment without polymer. Application of DEDTCm helped to achieve higher technological parameters in flotation of lowgrade Rt-Cu-Ni ore. Compared to the basic mode Pt recovery was plus 13%, Pd recovery was plus 9% and the content of precious metals in the rougher flotation concentrate increased in 2,5 - 4 times. The studies have been supported by Grants of the President of RF “Scientific School of Academician V.A. Chanturiya” NSh-220.2012.5, NSh-748.2014.5. Keywords: Au and Pt complex ores, flotation, flocculation, thermo-sensitive polymer TMPPh, modified collector

Jan 1, 2020

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

By C. Chibwe, M. Tadie

Copper electrowinning models are useful for prediction of process performance, optimisation and improved understanding of complex phenomena such as current distribution without the expense of physical experiments. Recently, finite element models such as those generated in COMSOL Multiphysics have been developed for the electrowinning process. The predictive capacity of these models is improved by incorporating physical and chemical phenomena. Since physicochemical properties of electrolytes can have a significant effect on the quality of copper produced, this work was conducted to investigate the effect of such properties on electrodeposition at varying levels of copper, sulphuric acid concentration, iron concentration and temperature, in the presence of a smoothing agent. Tests were conducted at conditions similar to those for industrial copper electrowinning. Mathematical correlations were developed for the following properties; density, conductivity and diffusivity which were compared to existing models in literature and thereafter applied in a COMSOL generated model. The model predicts, current distribution at the cathode surface, deposit thickness (morphology), concentration of species within the cell and current efficiency. Current distribution output shows the impact of several phenomena on the deposit generated including the relationship between increasing copper concentration and current density and lack of influence of acid concentration on this property. Keywords: Electrowinning, physicochemical properties, electrolyte composition, modelling

Jan 1, 2020

By O. O. Ogunmodimu, D. K. Weatherley, M. S. Powell

Discrete element methods (DEM) have provided the ability to resolve the complex phenomena experienced by ore within comminution devices such as tumbling mills. The new developments in DEM techniques and the corresponding increase in computational power have made it more feasible to study the movement of individual ore particles as they traverse a tumbling mill. A range of information can be extracted on individual particle impact histories, such as kinetic energy at the time of collision, velocities of individual particles, per-particle stress tensors, impulse, and collision energy. DEM codes have been modified to provide required information that can be analysed in associated software to investigate the impact of varied operational parameters on the resultant granular dynamics. This paper explores the reaction of individual ore particles to the breakage environment within a tumbling mill using DEM techniques and studies the stressing conditions that would lead to either impact or abrasive breakage. Keywords: DEM, comminution, tumbling mill, breakage

Jan 1, 2020

The proper understanding of the functioning of ground support under dynamic loading and the current approaches to designing of dynamic support are plagued by a great deal of uncertainty and lack of knowledge. This applies equally to the understanding of the support capacity as well as the demand placed onto the support due to dynamic loading. This lack of understanding currently leads to a case of design indeterminacy. This paper does not aim to solve this problem of design indeterminacy but to explore some of the issues that need consideration to obtain a better understanding of the dynamic demand on ground support systems. Keywords ground support, dynamic loading.

Dec 1, 2013

By T.R. Stacey

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014

By P. T. L. Koh, M. P. Schwarz

A series of parametric studies were carried out for a flotation cell using computational fluid dynamic (CFD) modelling to determine the local response of hydrodynamic performance measures to change in operating conditions. As an example, an Outotec cell was used to carry out the response analysis. The hydrodynamics of the flotation cell has been previously investigated by laboratory measurements presented by Schwarz et al (2019), and a CFD model of the cell was developed and validated using these measurement data (Schwarz et al., 2019). In this work, parametric studies have been performed by modelling the flotation cell at different stirring speeds and gas flowrates, varying above and below standard conditions. Predictions of void fraction, bubble size, bubble surface area flux and particle–bubble collision rate are presented showing the effects of increasing and decreasing stirring speed and gas flowrate around the base case. Generally, the total gas holdup in the flotation cell was found to increase with increasing gas flowrate. The bubble diameter was found to decrease with increasing stirring speed and increase with increasing gas flowrate. The collision rate increased with both stirring speed and gas flowrate. The parametric results show that there is a correlation between the bubble surface area flux Sb which is affected by stirring speed and gas flowrate, and the particle–bubble collision rate. With the collision rate as an indication of flotation collection, it is also possible to show that cell performance can improve more by increasing stirring speed than by increasing gas flowrate in a situation where everything else remains constant. The CFD results can form the basis for a Response Surface Method (RSM) analysis which can then be used for automated optimization of cell performance. Keywords: Flotation kinetics, computational fluid dynamics, bubble surface area flux, particle-bubble collision rate

Jan 1, 2020