Search Documents

By P. A. Botha

The production of iron and steel generates various types of waste materials containing oxides, carbon, and flux material. Usually, these materials are land-filled at the plant site or are hauled away for disposal. Some of these waste materials are hazardous, and they must therefore be recycled or disposed of properly. The influence of different waste materials in iron-ore sinter blends on the quality and operational parameters in sinter production is described. The recycling of waste materials such as dolochar, scrap fines, mill scale, electric-arc furnace slag, basic-oxygen-furnace mud via the sintering process can achieve a saving in the cost of the raw materials (for example, fuels and flux) and a reduction in pollution. A comparison of a typical sinter with a sinter produced through the utilization of waste materials shows a distinct correlation between certain types of waste material and some metallurgical properties and operational parameters. Dolochar (and arc-furnace slag) in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. In general, dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter, but not necessarily the operational parameters such as the production rate. At Vanderbijlpark, approximately 15 kt of various waste materials per month are successfully recycled in the sinter plant. Investigations into the handling and recycling of other waste materials may indicate that even more waste materials can be utilized.

Jan 1, 1993

By W. L. Van Heerden

In situ complete stress-strain characteristics of large coal specimens by W. L. VAN HEERDEN, B.Sc. Hons. (Pret.) (Visitor) The significance of ;n situ tests on large coal specimens is briefly reviewed. Tests aimed at obtaining complete stress-strain characteristics of large coal specimens with high width-to-height ratios are described. A formula for the relationship between strength and width-to-height ratios of coal pillars is proposed, and the influence of width to- height ratios on the deformation characteristics of pillars is discussed.

By J. A. L. Napier

SYNOPSIS Many tabular mining problems can be modelled effectively by displacement-discontinuity techniques, which can be extended directly to represent fracturing on discrete planes and movements on planes of weakness. This paper presents a unified method for computing the energy changes that occur when multiple discontinuities intersect and are extended incrementally. It shows how this method can be used to deduce energy-release information for standard layout problems and, in addition, how the technique can be incorporated in numerical procedures based on the displacement-discontinuity method. Examples are given to demonstrate the effects of off-reef fracturing and the importance of stope-fault intersections during seismic events.

Jan 1, 1991

By A. P. L. Kotzé

This paper gives a brief description of the control measures used in the establishment of the Grootegeluk Coal Mine, near Ellisras in the Transvaal. Specific reference is made to the planning offunds, cost and financial control, and economic evaluation.

Jan 1, 1982

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By D. W. Boydell, E. B. Viljoen

A flowsheet incorporating rotary-drum filtration for the solid-liquid separation step, followed by solvent extraction for uranium purification, is used as a standard against which four flowsheets are compared. These flowsheets employ either counter current decantation or belt filtration for solid-liquid separation, and either solvent extraction or continuous ion exchange plus solvent extraction for the purification step. Sales revenue, taxation, capital expenditure, and operating costs are estimated. These factors are taken into account in the calculation of an incremental net present value for each circuit by the discounting of cash flows at 25 per cent per year over a projected life of 15 years. For the material used in these examples, the highest net present value results from the circuit that employs belt filtration followed by continuous ion exchange and solvent extraction.

Jan 1, 1978

By B. N. Soutar

The design and operation of a double- V compartment vertical-flow settler by B. N. SOUTAR, B.Sc. (Mech. Eng.) Wits. (Visitor) This paper describes the development of a vertical-flow settler for underground pumping installations in the mines of Gold Fields of South Africa Ltd. The recommended settler employs the principle of 'dynamic filtration': the solids that are in suspension in mine water are filtered through a stable horizontal bed of flocculated particles, a technique that was established in about 1958.

Jan 3, 1977

A powerful, interactive metallurgical process simulator for use on micro- computers has been developed in the Department of Metallurgy and Materials Engineering at the University of the Witwatersrand. MICROSIM presently allows simulation of all ore-dressing flowsheets and a selection of hydrometallurgical unit operations, and is extendable to all such processes. MICROSIM is written in Pascal. This modern language provides very versatile data structures which can be effectively used to solve the major problem in generalised simulation programs, namely storage and transmission of data relating to liquid and solid phases. Dynamic memory allocation allows optimal utilisation of computer storage space. The simulator utilises very efficient precalculation algorithms that determine the tear streams for optimal sequential modulator calculation convergence. Microcomputer graphics simplifies flowsheet specification, and form-filling data capture with supplied default values eliminate most common input errors.

Jan 1, 1987

By P. R. Jochens

SYNOPSIS This review article first highlights the past performance of the industry and discusses the manner in which the development of the industry has followed a logical progression from mining to the production of mineral and metal products of specification purity. Then the numerous constraints against a greater contribution by the industry are enumerated. Attention is drawn to the extent of further processing that can be undertaken in the context of mining and metallurgical processing, not only to indicate the benefits that can be derived from the added-value conferred on a mineral or metal commodity during each stage of its further processing, but also to point out some important corollaries of further processing. The many opportunities and challenges for an increased contribution by the minerals and metals industry are then reviewed. This major section includes a list of commodities for which increased penetration of export markets could be sought because the increasing resistance level (a term developed in this paper) has not been attained; a list of commodities that are imported at present, many of which could be produced locally on the basis of identified resources and expertise; a list of commodities for which additional uses should be developed so that South Africa, which possesses the largest reserves and is the largest exporter, can increase its production rate; and examples of commodities for which further processing is still at an early stag*..

Jan 1, 1985

By J. P. Coetzee

Dr. K. Gebhard In his excellent and comprehensive survey on the future development of the Iron and Steel Industry in South Africa, Mr. Coetzee has also mentioned the direct reduction processes as a possible method of converting iron ore to iron. Mr. Coetzee has made it quite clear that at this stage one should not consider these processes as a 'magic formula' which herald a 'break through'. I agree entirely with this point of view. Once upon a time I held the opposite view, but in the meantime I have revised my views. To do so, I had 40 years at my disposal. In 1930 I had the privilege of being connected with the first commercial sponge iron plant in Germany1 - a plant which was capable of producing 40 tons of sponge iron a day. We were determined to prove that the blast furnace would become obsolete in the near future. We considered it as an unnecessary detour to convert iron ore first into an iron-carbon alloy, which contained further quite a number of undesirable elements, and to remove this carbon by an endothermic process. Direct iron-making seemed to be a logical short cut. Unfortunately, we were not able to establish this 'short cut,', but the life of our sponge iron plant was cut short. We had solved all technical but not the economic problems. Basically the positon is still the same today - mainly economic and to a lesser degree technological aspects determine the rate at which sponge iron plants are installed. More has been said and written than done about direct reduction plants. I think that there are two main reasons for this stagnation in the introduction of direct reduction processes. The first reason is that modern blast furnaces are just too good and too economic ever to be replaced by direct reduction processes on a large scale. This, of course, already limits the field of application for direct reduction plants. The second reason is that sponge iron production and utilisation is based on technical considerations, which increase not only the production cost of sponge iron but also the conversion cost to steel to such an extent that under special conditions only are direct reduction plants an economic proposition. Are these technical considerations still as forceful and valid today as they were when 'direct steelmaking' was first contemplated? The development of sponge iron production as a method of direct

Jan 3, 1971

By C. A. Cousins

Platinoids in the Witwatersrand system C. A. Cousins. (visitor) Study of the composition, nature and mode of occurrence of platinoid minerals in the conglomerates of the Witwatersrand System leads to some interesting conclusions. Genetic evidence strongly favours a placer origin, while comparison with modern alluvial platinoids supports this view but also indicates that they are very mature alluvials. The compositional patterns and distribution of the platinoids in the Witwatersrand basin suggest the water was saline. Study of the mineralogy was greatly facilitated by the electron-probe.

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991

By E. J. Maunders

This paper describes briefly a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25000 to 70000 tons of uranium, proves to be very data-sensitive.

By L. A. Vermeulen

Electronic circuits were developed and successfully utilized to record, store, and continuously transmit to a remote station physical information relating to the impacts of pebbles on the shell liners of an industrial pebble mill, and of electrical conduction in the mineral pulp. The information was obtained by the instrumentation of some of the bolts that are used to clamp the liner blocks and litter bars to the mill shell. The features associated with the impact and conduction signals have been interpreted, and it is shown that such signals can lead to continuous measurements of the volume of the load in an industrial mill. Information is given regarding the angular distribution of direct impacts of the pebbles onto the shell liners, the power required to promote impacts, the amount of material in flight, the impact velocity, and the average number of direct impacts with the shell liner that any given pebble undergoes in unit time in the given mill.

Jan 1, 1984

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By H. E. Cross

The conversion of a uranium plant to the recovery of zinc by H. E. CROSS. B.Sc. (Eng.)(Hons.) Rand (Fellow) The conversion of the Vogelstruisbult Uranium Plant into a plant for the production of electrolytic zinc is described. The reasons for the conversion, the preliminary investigations. and the basic design principles are all outlined, and a brief account is given of operating experience.. during the commissioning of the plant, with equipment that had been put to a use for which it was not originally Intended.

Jan 11, 1973

By M. C. van Blerck

This paper examines the South African fiscal system as it applies to the mining industry and, where components are found wanting, discusses possible alternatives. It is concluded that the South African system has long provided a stable environment for mining investment and growth. However, the introduction, of steep surcharges during the past decade or so (since abolished) and ring fencing (since relaxed but not abolished) has started undermining this stability.

Jan 1, 1994

By B. H. Sandelowsky

Prehistoric metal-working in South West Africa by B. H. SANDELOWSKY*, Ph.D. (Visitor) This paper describes a three-hundred year old metal-working site at Rehoboth, and makes a plea for information on such sites elsewhere in South West Africa so that they can be investigated. The technique of ore smelting that was used at Rehoboth appears to be different from that practised elsewhere by Bantu peoples before the modern era.

Jan 5, 1974

John Keith Elers Douglas recently retired from active participation in the activities of the South African Institute of Mining and Metallurgy after over forty years of diligent and valuable service to the Institute. This account of his contributions to the mineral industry and associated organizations is presented as a tribute to all his hard work and dedication. Mineral processing The Fourteenth International Mineral Processing Congress, sponsored by the Canadian Institute of Mining and Metallurgy, is to be held in Toronto from 22nd to 27th October, 1982. The theme of the meeting is 'Worldwide industrial application of mineral technology'.

Jan 1, 1981

By D. G. Hulbert, D. Tudors, M. L. Coetzee, I. K. Craig

The paper describes how a multivariable control scheme was developed and implemented for the run-of-mine milling circuit at a gold mine belonging to Vaal Reefs Exploration & Mining Company Limited. The key variables that are controlled are slurry level in the sump, mass of material in the mil, and product size. The control scheme has resulted in reliable control of the dynamics of the plant, and has provided a good basis for the optimization of plant operation by the selection of suitable set Points.

Jan 1, 1990