Search Documents

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l'étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L'étude de champs a démontré l'interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l'influence d'augmenter de dimension de l'excavation. La raideur de piliers overburden, la proportion d'extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d'influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d'un pilier a reçu l'influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L'impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d'interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003

By V. Ross

"Bench-scale flotation tests play a major role in the geometallurgical process value chain. Despite their apparent simplicity, these tests pose pitfalls in terms of operation, as well as the interpretation and modelling of results. In this paper we highlight key aspects to consider in generating accurate and reproducible experimental results, and critically review some assumptions relating to the estimation of entrainment and froth recovery. We subsequently focus on first-order equations to model kinetics and propose a method that accounts more realistically for the decay in kinetics over the duration of a float, and the contributions of froth stability and hence mass pull. The method was applied to three case studies on platinum group metal (PGM) ores and matched or outperformed first-order, two-component models. Also, it allows for a deeper analysis of the integrity of the bench-scale flotation results. IntroductionGeometallurgy is a structured, multidisciplinary approach that integrates key data from the geological, mining, mineralogical, and metallurgical aspects of the value chain to construct spatial models of an ore deposit such that the overall economic benefit and sustainability of an operation can be optimized. Process geometallurgy is aimed primarily at enhancing metallurgical efficiency and plant throughput by the application of appropriate mining and processing strategies, as well as supporting production planning and operational strategies to reduce the impact of highly variable ores. With flotation being the dominant concentrating process in the mineral value chain, the bench-scale flotation test is an important characterization tool – a relatively cheap, simple, and rapid way to obtain key information about the ore and its amenability to economic extraction of valuable minerals. This includes the evaluation of different ore types and the implications of mineralogical composition and texture for comminution and floatability, the effect of the grinding environment on the liberation of minerals, the electrochemical environment in the pulp (Bradshaw et al., 2006), the screening of reagents to improve floatability (Ekmekci et al., 2003), and the role of hydrodynamics in the recovery of valuables and the entrainment of gangue (Amini et al., 2016; Wang et al., 2016). It is also a critical tool in auditing the performance of a flotation plant by hot floats, paving the way for concept and feasibility studies and providing essential data on kinetics for the purposes of scale-up, optimization, and simulation of flotation circuits."

Mar 1, 2019

By C. Musingwini

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility (or tactical flexibility), mainly due to its nebulous nature. By glossing over technical operating flexibility the resultant mine layouts and schedules maybe suboptimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. The nature of technical operating flexibility is illustrated, previous work on valuing of operating flexibility reviewed, and a proposal made on how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility has been quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. This paper is a revised version of a paper presented in the Proceedings of the Second International Platinum Conference, ?Platinum Surges Ahead? in 2006. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility/tactical flexibility, ore availability.

Jan 1, 2007

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1980. Mr D. A. Viljoen (President) was in the chair and declared the meeting open at 4.05 p.m. Obituaries President: It is my sad duty to announce the death of the following members of the Institute: T. C. A. Meyer (Past President, 1941 to 1942); E. G. Harding, T. A. Stannard, C. T. Hardy, W. C. Jackson, J. S. Sinton, G. H. Duggan, H. H. A. Muller (Life Fellows); W. M. Frames, K. Gebhard, W. M. Walker, S. L. S. Swart, N. W. Stansmore, H. E. Allen, B. W. F. Towne, R. A. Wilson, D. Waterman (Fellows), R. M. Peterson (Life Member); D. L. Gibbs (Member); B. M. Williams (Asso¬ciate Member); D. B. T. Cresswell, P. G. Guernier (Associates). As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments of silence. Notules President: Kan ons die notules van die Algemene Jaar¬vergadering, wat op 22 Augustus 1979 gehou was en in die September uitgawe van ons Joernaal gepubliseer is, bevestig? Bevestig.

Jan 1, 1980

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By B. Haimson

A new loading apparatus was fabricated and used to conduct true-triaxial compression tests on KTB amphibolite, a crystalline basement rock. Tests in dry jacketed samples reveal that the intermediate principal stress has a significant effect on the onset of dilatancy and on rock strength, contrary to the implicit assumption made by Mohr-type failure criteria. Failure is induced through a shear fracture that dips steeply in the direction of the least principal stress. Experimental results lead to a new generalized strength criterion in terms of all three principal stresses. Unjacketed KTB amphibolite specimens, exposed to confining fluid, are considerably weaker than the jacketed ones, despite the negligible porosity and permeability. Failure is facilitated by several closely spaced subparallel tensile cracks normal to the least stress direction. SEM analysis suggests that microcracks developed upon dilatancy onset are penetrated and extended by the confining fluid, bringing about the unexpected rock failure mechanism at reduced stress levels. Un nouveau dispositif à chargement fut fabriqué et utilisé afin de réaliser un vrai essai de compression tri-axial sur KTB amphibolite, une roche cristalline du sous-sol. Les essais effectués sur échantillons enveloppés et secs révèlent que les contraintes principales intermédiaires affectent considérablement le début de la dilatance et la résistance de la roche, contrairement à la supposition fondée sur le critère de rupture de Mohr. La rupture est produite grâce à une cassure de cisaillement très incliner en direction où la contrainte principale est moindre. Ces résultats expérimentaux indiquent un nouveau critère de rupture général en fonction des trois contraintes principales. Les échantillons de KTB amphibolites sans enveloppe, exposés à un liquide confiné, sont considérablement plus faibles que ceux enveloppés, malgré la porosité et la perméabilité négligeable. La rupture est facilitée par plusieurs fissures de traction adjacentes et sub-parallèles, normales à la plus petite contrainte principale. L’analyse SEM suggère que les micro-fissures développent suivant le début de la dilatance, elles sont pénétrées et agrandies par le liquide confiné, produisant un mécanisme de rupture de roche inattendu, ceci à un niveau de contrainte réduit. Ein neuer Ladungsapparat wurde hergestellt um real - triaxiale Druckfestigkeitsversuche in KTB Amphibolit, einem kristallinen Grundgebirgsgestein, durchzuführen. Messungen in trockenen, bedeckten Proben zeigen that die mittlere Hauptspannung eine bedeutende Wirkung auf das Einsetzen von Dilatanz und auf die Stärke des Gesteins hat, im Gegensatz zu der impliciten Annahme auf Grund von Mohr-ähnlichen Versagungskriterien. Versagen ist induziert durch eine Scherfraktur die sich steil in die Richtung der geringsten Haupspannung nach unten senkt. Messergebnisse führen zu einem neuen, verallgemeinerten Stärke Kriterium dass auf alle drei Hauptspannungen basiert ist. Unbedeckte KTB Amphibolit Proben, die unmittelbar den umgebenden Fluiden ausgesetzt sind, sind wesentlich schwächer als bedeckte, trotz geringfügiger Permeabilität und Porosität. Versagen wird gefördert durch mehrere, nebeneinander liegende, sub-parallele Spannungsbrüche, normal zu der geringsten Spannungsrichtung. SEM Analyse lässt vermuten dass Mikrobrüche, die sich beim Überschreiten der Dilatanzschwelle entwickeln, durch die umgebenden Fluiden fortgepflanzt und weiter verbreitet werden, und unerwartet, auf Grund der reduzierten Spannungswerte, den Versagungsmechanismus des Gesteins einleiten

Jan 1, 2003

By R. T. Jones

Base metals and platinum group metals can be collected in metallic alloy form, via a wide variety of smelting processes. The recovery, or degree of collection, of the valuable metals is a function of the extent of reduction in the furnace, which, in turn, is indicated by the fraction of iron present in the feed materials that report to the alloy. An equation has been developed that relates the recovery of various metals (such as Ni, Co, Cr, and PGMs) to the recovery of Fe. This recovery equation (for each metal) is characterized by a single parameter (K?) that can either be empirically fitted to the data, or expressed in terms of the equilibrium constant and the ratios of the activity coefficients involved. Data from a number of varied DC arc furnace campaigns are presented to illustrate this behaviour.

Jan 1, 2009

By Pieter de Waal

The use of valuable minerals is a necessity to maintain a modern society. Not only the iron, aluminium, coal and oil that are used in large quantities, but also the uranium, copper, vanadium, tungsten, antimony and many others play an essential role in the bigger picture of our modern civilisation. Minerals occur in a form and in places determined by a long history starting at the dawn of creation. Over billions of years the elements have combined in wondrous combinations and structures. They have been broken up by massive explosions, movements in the earth's crust and erosion by wind and water. They have been restructured and recreated in even more configurations by the application of heat and pressure, leached by and exposed to new chemical compounds. The result is that most valuable minerals are found in impure form and mixed up with other, less useful waste material. 2. Mineral Beneficiation The processes used for the purification and enhancement of an ore, to satisfy the needs of downstream applications, are collectively referred to as mineral beneficiation. Mineral Beneficiation starts in the mine where only that portion of the ore, that can be economically processed, is selectively extracted. It may also include ore blending, to ensure a more consistent feed to the following stage of valuable mineral recovery. The next stage in mineral beneficiation is the liberation of the valuable minerals from the gangue. This is achieved by blasting, crushing, milling and grinding down to an adequately fine grain size to facilitate good separation. Separation can be achieved by a variety of different techniques. ?Screening coarse from fine particles is an easy method if the valuable mineral is dominant in a certain screen fraction. ?Magnetic separators can differentiate minerals on the basis of their difference in magnetic susceptibility. ? Electrostatic separators differentiate on the basis of electrical conductivity. ? The differences in density are exploited in spirals and jigs. ? Particular surface properties provide a separation technique in flotation. ?The selective sorption properties of a collector medium are another option.

Jan 1, 2007

By G. H. Grange

The control of dust from mine dumps by G. H. GRANGE Pr. Eng., B.Sc. (Min. Eng.) (Rand) (Fellow) This paper gives a resume of the early attempts to control dust from mine dumps, leading up to the research project undertaken by the Chamber of Mines ResearchLaboratories to explore the possibilities of establishing vegetation on dump surfaces. The ultimate success of this work and details of the principles involved are outlined. Also given are a brief history of the event that culminated in the introduction of the Atmospheric Pollution Prevention Act in 1965, details of the control of dust in terms of this Act, and a short summary of the dust-control work.

Jan 3, 1973

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

By B. S. Spottiswoode

Lack of visibility makes it difficult for continuous miner (CM) operators to judge the desired sump depth. The resulting inaccuracies have proven to lead to significant production losses. This problem of measuring the depth of sump has been addressed in the past and a few measurement techniques have evolved. Despite various attempts, a suitable commercial depth of sump sensor does not yet exist. A system using the Doppler effect has been patented, developed and successfully tested. The method is non-intrusive and involves a beam of microwaves being projected obliquely at the roof. The received signal is analysed with respect to the transmitted signal, yielding the desired measure of displacement. Surface tests have revealed an accuracy of a few centimetres. Underground simulation tests on a load haulage dump (LHD) machine have verified the repeatability under the harsh conditions of interest. The system is presently being installed on a CM where it is to undergo a long-term performance evaluation. This paper presents the theory behind such a system, the hardware developed, the signal processing requirements and an analysis of the test results.

Sep 1, 2001

By L. Holappa

Ferroalloy production is an energy-intensive industrial sector with significant CO2 emissions. In this paper the current situation in ferroalloy processes is discussed from the standpoint of global environmental issues, trends and development. Progress and data of ferroalloys production are frequently compared with the steel industry, which is a closely related sector and the main user of ferroalloys. Emission factors of processes and electricity production are examined as well as possibilities and future scenarios of how to diminish CO2 emissions. As a part of this study a questionnaire was submitted to experts in the field of ferroalloys worldwide to survey opinions on the ferroalloy industry today and in the near future (2020). Eighteen questions concerning raw materials, energy, environmental aspects, by-products and economic aspects were responded to by seventeen experts, the answers were analysed and conclusions were drawn. Keywords Ferroalloys, energy, CO2 emissions, electricity, sustainability, questionnaire.

Jan 1, 2010

By J. L. Fuentes-Cantillana, J. B. Solar Menéndez, A. O. Cámara

The Principality of Asturias is a region situated in Northern Spain with two centuries of tradition in underground coal mining. In addition, its uneven relief has obliged the construction of a great number of tunnels both for railways and roads. Basing on this experience and an ever increasing need to improve on safety, the Barredo Foundation dependent on the Regional Government and the University, provides and manages a Centre for Research of Fires and Ventilation in Tunnels. The Centre has as its most important infrastructure, a tunnel 540 m long, 9,5 m wide and 8,0 m high at centre. This section coupled with ventilation equipment allows the simulation of risk conditions at real scale, which is achieved by modifying the geometry of the section and through two powerful stations situated one at either en of the tunnel. In addition, the Centre houses two test benches for fans and electrical motors at high temperatures. One bench with a re-circulation conduit is the most appropriate for tests in Transversal and Semi-transversal type of installations. The other, is for the testing of electrical motors or fans which operate in zones where the surrounding temperature is high. In this Centre, training has also been developed for Fire Fighters and Civilian Protection Personnel who have to work in fire and smoke rescue conditions in underground structures. Testing conducted at real scale enables this formation and also to improve different computer programmes in the field of Fires and Ventilation.

Jan 1, 2003

By G. Wu, S. Liu

In view of the singleness of traditional methods about international petroleum (Brant) price forecast, ten main factors that affect international petroleum price are fully analysed. Based on time series method and multivariate linear regression method, the simulation model with the theory and idea of system simulation is firstly established. And this forecasting system realizes visual operation under the environment of MATLAB/SIMULINK. So this article tries a new way for further exploring petroleum price’s running law and guiding its forecasting practice. Keywords: Petroleum price forecast, system simulation, residual error, physical flows information flows

Jan 1, 2003

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009