Search Documents

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By Samuel M. Brock

Problems related to strip and auger coal mining have grown with the development of the industry and the economy. New technology has produced equipment that has made mining by surface methods not only highly productive, but potentially highly destructive of water resources and natural environments. On the other hand, growth of the economy has produced an increased demand for clean water, and created new demands for amenity values that natural environments provide. Thus, opposing forces have created conflicts in resource use. And these conflicts have made surface mining highly controversial. Resolving the controversy will require the solving of complex economic and social problems. The essence of the economic problem created by surface mining is that, in the absence of proper regulation, substantial costs resulting from the process are borne by the public rather than the mine operator.

Jan 1, 1968

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By M. Machina

Anew approach to the use of projectiles for rock fragmentation uses recently-developed technology to optimize projectile shape and composition to achieve the desired type of breakage. Projectiles can also be made of various materials, as determined by the requirements of downstream processes. This paper describes laboratory tests with an 21-mm (8-guage) gun, and field tests with a 60-mm cannon.

Jan 1, 2003

By Frank L. Peterson

This paper deals with problems of groundwater development in an insular circum-Pacific environment, and is not oriented as such to mining and mineral development. Nonetheless, because a reliable water supply is necessary for most mining and related support activities, and since water supplies are limited in many insular parts of the Pacific Basin, groundwater development is a subject which must be frequently addressed. Because many in the audience may be already familiar with groundwater development for continental environments, I have chosen to deal with groundwater occurrence and development problems which for the most part are unique to insular environments. In such environments, the local geology plays a critical role in determining groundwater occurrence and its suitability for development. The three examples discussed in this paper-Hawaii, Guam, and the Marshall Islands-were selected because they illustrate groundwater occurrence in a wide range of geologic conditions. For example, the Hawaiian aquifers consist primarily of basaltic lavas, while Guam is made up of andesitic lavas and coral reef limestones, and the Marshall Islands are coral atoll deposits. Despite differences in aquifer size and rock types, the principal mode of groundwater occurrence at the three sites is similar; thus, development strategies are also similar. Figure 1 shows the location of the three sites.

Jan 1, 1982

By P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on Uranium Resource Evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources. The standard classification was prepared with participation of representatives from the Dept. of Energy, the Dept. of Interior's Geological Survey and Bureau of Mines, utilities, and consultants. The classification of a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alpha-numeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An effort is underway to develop estimation criteria to guide users in classifying a resource according to the above format.

Jan 1, 1983

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By D. R. Schricker

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment.

Jan 1, 1990

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

By F. W. Metzger

Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin of Wyoming are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic sub-units, of the coal seam can be made. These units must be recognizable in the core and also on geophysical logs.

Jan 1, 1981

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By Bruce F. Bohor

Silica sand has been mined in Illinois from the St. Peter Sandstone since the turn of the century, especially in the area around Ottawa on the Illinois River in the north-central part of the state. Production of this sand, consumed mainly by the glass and foundry industries but also sought after for many other uses, has grown with the economy, and last year's output in Illinois exceeded 4,000,000 tons. Such an important commodity was given the early attention of the Illinois State Geological Survey, and a very complete report was issued in 1928, authored by J. E. Lamar. The mining and processing of the sand has changed very little during the intervening 40 years, so that much of Lamar's data and descriptions are applicable today. More recently, the stratigraphy of the St. Peter Sandstone in north-central Illinois has become better known from the work of Willman and Payne (1942). The present authors have borrowed generously from Lamar's publication, and we wish to acknowledge the contribution of both of these studies to our work.

Jan 1, 1969

By B. Markovic

Performance of mineral filler particles in ceramic applications can be enhanced markedly by adsorbing polymers of optimum molecular structure and dosage. In a recent work by Chen and Somasundaran (1997), a novel scheme of controlled polymer adsorption was used to produce nanocomposites of unique core-shell designs. Towards this purpose, adsorption and desorption behavior of selected polyacrylic acids (PAA) on three minerals; alumina, titania, and silicon carbide, was examined as a function of relevant parameters. Adsorption of P AA was found to depend on polymer molecular weight, pH, as well as solids loading. Specifically, the adsorption density was found to increase with increase in polymer molecular weight for non-porous alumina while it was found to decrease in the case of porous alumina. This is attributed to the inaccessibility of the pores to the larger polymers. An unexpected finding was the change in the adsorption density of PAA with solids loadings. PAA adsorbs on silicon carbide only at low pH values when the particles have very low surface charge suggesting that the adsorption in this case is controlled by electrostatic forces. Using polyacrylic acid as bridging agent between the alumina fillers (core) and nanosize alumina or titania particles (shells), controlled layer by layer deposition of nanoparticle on the core particle surface could be obtained.

Jan 1, 1997

By James B. Loftis

The importance of increasing the world's mineral production to help solve our food and energy problems has been widely discussed. Improved surface mining methods will be needed to meet these needs. This paper reviews the modern horizontal drilling and blasting methods which can increase the productivity and lower the costs of I surface mining. A substantial decrease in the number of blast holes required, total footage of blast hole required and amount of explosive used has been realized by many mining companies using this method. Applications of this method are presently in large coal surface mines. However, similar gains are possible and probable in open pit mining of copper and iron.

Jan 1, 1975

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By Norman R. Paterson

In November 1980 a combined airborne electro-magnetic (INPUT.) and magnetometer survey was conducted by Questor Surveys Limited in the State Line Area, Colorado-Wyoming. The survey was the result of discussions over a prolonged period between the authors and various investigators of the State kimberlite occurrences. As a result of these discussions and literature studies, it was decided that airborne geophysical methods would be potentially useful in the exploration for new kimberlite occurrences. The survey was designed by Paterson, Grant and Watson Limited and conducted by Questor Surveys Limited over an area in which more than 15 kimberlite bodies were known and on some of which ground geophysical surveys had been conducted. The survey was designed primarily to determine the airborne electromagnetic and magnetic responses of the known occurrences and to deter- mine whether these responses would be detectable under similar conditions in other parts of the State Line District and elsewhere.

Jan 1, 1984

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991