Search Documents

By E. D. Hummer

During the planning phase of the fine coal cleaning addition at the Gary Coal Preparation Plant, careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at 1/4 inch, pumping the minus 1/4 inch raw coal to bowl desiltors for desliming, and then cleaning the disliked raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 foot diameter thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh Today the minus 48 mesh refuse at Gary consists of thickened flotation tailings and thickened spiral classifier overflow. The transportation of large quantities of fine wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds

Jan 1, 1965

By Wenbing Guo, Mingjie Guo, Hebing Zhang

As resources are depleted in coal mines, isolated support pillars are often mined. Cemented paste backfill has been used to provide support during the mining of these pillars due to its safe and green mining characteristics. However, traditional cemented paste backfill mining has some shortcomings, such as poor adaptability to geological structure, leakage of paste during filling, imperfect roof-contact in partially backfilled areas, and insufficient roof strata support before the backfill reaches its design strength. This paper presents the results of a case study where L-shaped interval cemented paste backfill technology has been safely used to mine an isolated coal panel beneath existing surface structures. This backfilling method has the advantages of preventing paste leakage, improving the backfilled ratio, reducing surface subsidence, and strongly adapting to geological structure. During this field application, the setting pressure of the backfill shield reached 20 MPa, the compressive strength of the backfilling body reached 2.0 MPa, and the backfilled ratio reached 93.7%. Observational ground monitoring showed that roof-to-floor convergence in adjacent roadways ranged from 132 to 167 mm. No obvious fractures or separations in the overlying strata were observed by a borescope. The maximum surface subsidence was 342 mm, the subsidence factor was 0.136, and the damage to surface buildings was within Grade I (slight damage). This case study clearly demonstrates that the L-shaped interval cemented paste backfill method can be safely used to mine the isolated coal panel beneath surface buildings.

Jul 1, 2023

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By John E. Anderson, Charles A. III Cravotta, Eleanora I. Robbins, E. Terrance Slonecker, Gordon L. Nord

Remote sensing is being tested for its ability to identify the severity of impact on streams that are subjected to contaminated mine drainage (CMD) in the Southern Anthracite Coalfield of Pennsylvania. Airborne digital multispectral video images of acidic and near-neutral CMD are being compared with field spectra, water chemistry, mineralogy, and microbiology. Spectral differences in the visible region of the electromagnetic spectrum are caused by the presence of schwertmannite in the acidic precipitates and ferrihydrite in the near- neutral precipitates. The acidic CMD averages 1,500 mg/L sulfate and has bacteria coated with schwertmannite; the near-neutral CMD averages 87 mg/L sulfate and has bacteria coated with ferrihydrite.

Jan 1, 2000

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By Dongxu Jia, Chen Cao, Shuangwen Ma, Jun Han, Huibin Ma

Coal bump, or coal burst, is one of the catastrophic disasters in underground coalmine. Among them, approximate 80% of recorded destructive burst events were occurred in mining roadway. The bump panel is often formed by hard coal seam and hard main roof; however, the cause and course of the bump events are not understood yet. This study provides a fundamental theory for the causality and progress of a coal bump event occurred in longwall roadway. Considering hard roof condition commonly existed in bump panels, we think that the abutment pressure induced by suspended roof behind the working face is the trigger of a coal bump event occurred in the roadway. Once high abutment pressure is concentrated on the hard coal seam around the working face, the roof and the coal around the working face form a seesaw-like structure, which leads the roof in front of the working face moving upwards. The movement of roof uplifting in front of the working face is a well evidenced phenomenon in practice, namely, roof rebounding, which causes unloading of the normal stress on the roof-coal interface around the roadway. A rib coal block bump mechanical model has been developed to establish the critical equilibrium equation of the coal block. Result shows that, the force source of coal bump is the horizontal ground stress perpendicular to the rib surface; and the slippage of the coal block is caused by the unloading of the normal stress acting on the roof-coal interface. Based on the causality and consequence theory of coal bump developed in the paper, several new prediction and prevention measures have been developed, including roadway design and in-tunnel reinforcing methods. The commonly used prevention measures in present have also been discussed. This paper presents a comprehensive explanation of coal bumps occurred in longwall roadways, from abutment pressure at working face forming seesaw structure to roof rebounding leading slippage of the rib coal mass into roadway, which provides a fundamental theory for coal bump causality mechanism and prediction and prevention technology.

Apr 26, 2022

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO's Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By J. L. Goodier

The paper points up the hesitance of private capital to pursue development of offshore mineral mining endeavors due to the deterrent effect of the clouded legal status of such endeavors. Some states have no laws or regulations to protect the potential exploiter. Others have regulations which give no proprietary rights of exploration to mineral discoveries. The above factors and others are discussed and analyzed in some detail, covering, in turn, summations of the federal regulations and of each of the coastal states. Some comparative analyses are provided, and some recommendations for encouragement to capital investors are made.

Jan 1, 1968

By R. W. M. Lai

In flotation or hydrometallurgical leaching of minerals, the cumulative metals recovery for a given process condition generally approaches a maximum value or an asymptote as the process time increases. This paper discusses the experimental methods of identifying and obtaining the asymptote of metals recovery through kinetic studies. In flotation, the kinetic asymptote of metal recovery, or ultimate recovery, is a function of grinding and collector dosage, but within a realistic variable range, is not a function of pH or temperature. However, variations in grinding, collector dosage, pH and temperature, all exert noticeable effects on flotation kinetics. Frothers generally have a minor affect on the asymptote, but have a major affect on flotation kinetics. The asymptote from batch flotation is found to be identical to that of a continuous flotation. In hydrometallurgical Leaching, the asymptote of metal recovery for a given leaching system is a function of such variables as temperature, particle size, and acid concentration.

Jan 1, 1983

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

By Frank C. Schora

The Institute of Gas Technology for many years has dedicated a large portion of its research effort to the development of a practical solid-fuel-based gasification process to produce a synthetic natural gas equivalent. The work is being done to prepare for the day when supplemental gas will be needed. This program, initially supported by the American Gas Association, and now by both the Department of Interior's Office of Coal Research and the American Gas Association, has developed the IGT Hydrogasification Process. This process, now entering the pilot plant stage, is based on the high-temperature, high- pressure hydrogenation of coal with a hydrogen-steam bearing gas. Product gas from this step is cleaned and catalytically methanated to produce a high-Btu gas. Estimated production costs indicate the process will be competitive with natural gas in certain areas of the country when required.

Jan 1, 1969

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By L. C. E. FEIO, R. RAMSDEN

In many parts of the world deep level mining relies heavily on the use of refrigeration for providing safe thermal underground conditions. The trend in South Africa in recent years has been to locate the refrigeration plants on surface and to use these plants to chill water that is then distributed throughout the mine. The surface cooling installation normally consists of a pre-cooling tower in which water is first chilled before it is sent to one or more refrigeration plants for further cooling. Presently, the majority of these refrigeration plants use CFC refrigerants; however, to conform with the Montreal Protocol, these plants will have to be replaced or converted for use with alternative refrigerants. The optimum design criteria for installations using the new generation of refrigerants will be affected by their characteristics and are likely to be different from those currently in use. In light of these developments the industry is examining a number of alternative systems for future installations including water vapour refrigeration. Factors that affect the decision on the type of refrigeration system to be used in mine installations are reviewed. INTRODUCTION Gold mining has been carried out in South Africa for over 100 years and most of the reserves close to surface have been mined out; this has led to mining taking place at greater depths, approaching 4000 m below surface. One of the consequences of operating at these greater depths is that it is necessary to install refrigeration plants to cool the ventilation air so as to provide safe and healthy working conditions. With the current low precious metal prices there is pressure on mines to cut costs and in recent years there has been considerable effort devoted to the design of more cost effective and efficient refrigeration plants and cooling systems. In the last 10 years there have been many studies into the use of ice for specific applications (Eschenburg et al., 1986; Hemp, 1988 and Ramsden and Lloyd, 1992) and at present there are three ice making plants in operation on South African mines, each of which produces ice in different processes. In addition, detailed design studies have been carried out on the "split ammonia system" (Napier and Patterson, 1992). In this refrigeration system the evaporator is located underground close to where the cooling is needed, whilst the condenser and heat rejection system is on surface. As far as refrigeration plants are concerned the trend has been to move away from standard package units to custom built refrigeration installations. This has given the design engineer greater flexibility in the choice of key components for refrigeration installations. For example both screw and centrifugal compressors are used, the heat exchangers for the evaporators and condensers may be either plate or shell and tube, and in a number of installations evaporative condensers are used. In addition, the following refrigerants are in use, R12, R22 and ammonia. The acceptance of the Montreal Protocol and its amendments by the South African government will restrict the use of CFC refrigerants and it will be necessary to re-evaluate various refrigeration systems, including those that do not use conventional refrigerants, such as air cycle and water vapour systems, for new surface installations. Although new systems and refrigerants are being developed, only the following refrigeration installations will be compared in this paper: - a refrigeration system using R134a which has properties similar to R12 - refrigeration system using R22 or a new alternative refrigerant with very similar properties - an ammonia refrigeration system - a water vapour refrigeration system The benefits of new cooling systems are not discussed in detail, since they are largely mine specific and outside the scope of the present paper. Since the optimum design for an air cycle system (del Castillo, 1988) is dependent on the mine layout, this system is also not included.

Jan 1, 1993

By Paul H. Earl

This paper discusses the evolution of a modeling methodology for explaining price behavior in the aluminum industry. Three generations are described, each utilizing as a foundation a microeconomic stages-of-processing approach. The second generation represents an improvement over the initial version, by incorporating more rigorous specifications of energy cost, and market strength (demand-supply balance) as well as endogenous treatment of market strength. International linkages across prices, costs, and markets, are the major extensions in the third generation. The discussion covers theoretical considerations, data problems and limitations, and model specifications. Simulation and forecasting properties of the models are also addressed.

Jan 1, 1979

By Yves C. Lizotte

Although blasting remains the most inexpensive method of fragmentation in hardrock mining, the significance of the costs of blast-induced rockmass damage in terms of mining efficiency and safety is becoming increasingly recognized. There is no straightforward and systematic method of adequately measuring blast damage in on-going mining operations. This paper considers various techniques available to measure blast damage, making particular reference to recent underground hardrock mine studies. It concludes by proposing a damage audit procedure for integration into routine mine production control.

Jan 1, 1996

By Carl P. Venzke

Mining lignite in the Gulf Coast often requires some interaction with shallow ground water system. Suggestions for determining ground water data and analysis requirements for regulatory compliance are given. Simple methods for estimating mine inflow seepage, ground water level declines, and changes in ground water chemistry, which may result from mining, are discussed. The mining of lignite often results in interaction with shallow ground water systems. An evaluation of the interaction is required as input to mine permitting and engineering. Your evaluation will proceed more smoothly and produce more meaningful results with some planning prior to performing your evaluation. The following are tips to consider in planning and carrying out a successful study.

Jan 1, 1982

By Henri Letient, Tom Aley, David Evans

Antamina is a large open-pit copper and zinc mine located within the Central Andes of Northern Peru at an altitude of 4300 masl. The facilities are situated within the headwaters of several watersheds, within the Amazon basin. Nearby villages rely heavily on springs and streams for drinking and irrigation water. The principle source of baseflow during the dry season is from Cretaceous karstic limestone aquifers. Antamina will produce nearly 1.4 billion tonnes of waste rock over its mine life. Finding suitable sites for storing large volumes of waste rock is often a challenging task – especially in karstic, alpine terrain. Detailed hydrogeological investigations are essential for delineating the karstic hydrogeologic watersheds associated with the proposed waste facilities, which are often very different than topographic (hydrologic) watersheds. Contamination vulnerability mapping at Antamina consisted of geological and karst mapping, geophysical surveys, geochemical testing, dye-tracer studies, drilling and aquifer testing. Detailed mapping followed by dye-tracer studies proved to be the most cost-effective methods for characterizing the karst aquifer systems. The results were used to optimize waste rock management at the site to minimize potential impacts on groundwater resources.

Jan 1, 2005