Search Documents

By M. J. Virnig

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-1 and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

Unless otherwise indicated, pounds are US avoirdupois, feet are US, and gallons are US.

Jan 1, 1985

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By Clinton Strachan, Rob Dorey

10.1 INTRODUCTION This chapter presents considerations which should be applied to heap leach pad site selection, site evaluation, and design, relative to the geotechnics of the site and ore. 10.1.1 General Guidelines are presented covering the topics encountered in design and construction of heap leach faci1ities. Because geotechnical characteristics vary from site to site, not all geotechnical topics associated with a specific heap leach facility are presented, and there may be exceptions to some of these guidelines. The general features of a heap leach facility (from Chapter 1) to be discussed in this chapter are: • Leach pad (including leach pad foundation and liner); • Heap; • Solution storage faci1ities (for pregnant and barren process solutions) ; and • Solution collection facilities (which collect and convey solutions in the heap and convey them to solution storage facilities). These general features are illustrated in Figure 10.1. Liners for these facilities are discussed in Chapter 11. Solution application systems and the sizing aspects of solution storage facilities are discussed in Chapters 6, 7, and 12. The general features listed above are constructed with and overlie naturally occurring materials (such as ore, borrow soils, and subsurface soils and rock). These natural materials are relied upon to perform in an acceptable manner as a component of the leach facility (such as the liner, drain material, and foundation).

Jan 1, 1988

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By Ossi V. I. Hintikka

There are several limestone deposits around the Lohja area in southern Finland. Raw material for cement rock is mined from some of them. The formations are geologically complicated, and therefore selective mining is used whenever possible. One of these mines is the Tytyri underground limestone mine, which is divided into two parts; Törmä and Solhem. In addition to the selective mining system hand sorting or picking must be used at the Tytyri mine to improve the overall grade of the blended limestone. Some means were needed in order to improve the quality and to increase the feed rate by the elimination of hand sorting. Sorting machines were considered and eventually a Sortex 811MW was pilot plant tested at the Ojamo mine near Tytyri. This machine now continues to be used on production.

Jan 1, 1971

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964

By David P. Keller, George Podolsky

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The world production of iron oxide pigments is estimated by the authors to be between 350 and 400 kt. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test which now has some 20,000 years of exposure. In addition to abundance, iron oxides (about 7% of the earth's crust) have the advantage of low cost, permanency, and are non- toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when these properties were desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States, the combined production of natural and synthetic iron oxides produced sales of over $97 million in 1980 (Spimad, Jr., 1980), increasing to $138 million by 1990 (Templeton, 1990) NOMENCLATURE With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products that are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a competitive commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and are able to command a premium price over iron ores used for steel manufacturing. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary particles are produced as opposed to the use of comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1994

By G. E. Maryniak

To date, human space exploration has been almost completely dependent on the use of resources carried with astronauts and cosmonauts from the surface of the Earth. The only exception to this has been the harvesting of solar energy to power space stations like Skylab, Salyut and Mir for long-duration missions. This dependence on materials which must be transported into orbit at costs in excess of $5000 per pound is the fundamental limiting factor in space exploration and operations. It is likely that launch costs can eventually be greatly reduced by means of such innovations as true single stage to orbit vehicles, aerospace planes, or serial electromagnetic or laser launch systems. However, the Earth will always remain an expensive source of materials for space construction and for basic commodities such as propellant and life support liquids and gasses. Fortunately, abundant sources of materials exist which are already in space, outside of the Earth's deep gravity well.

Jan 1, 1992

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry's further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By R. F. Korcak

There exists a wide array of industrial by-products that can be shown to produce beneficial responses in the soil/plant environment. These materials range from clean coal technology residues produced in the generation of electric power, particularly those high in gypsum, to mineral 'fines' produced by the aggregates and crushed stone industries. A number of these materials will be examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems will be discussed.

Jan 1, 1995

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By Richard C. Enochs

In order to clearly understand our process control system it is necessary to briefly discuss the various process control systems that were considered and why we chose our particular configuration. We considered Analog Systems, Computer Supervisory Systems, Computer Setpoint Systems, Direct Digital Systems and Direct Digital with Backup Systems. Our concept of these systems is illustrated in Figure 1 through Figure 5. We chose Direct Digital Control with Manual Backup because it had the greatest flexibility, ease of implementation and cost no more than a pure Analog Control System for one control concept. There would be no increase for a Direct Digital Control with Manual Backup System if the control concept were changed, while there could be considerable additional cost with an Analog System, if the control concept were changed.

Jan 1, 1975

By D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool including techniques such as expert systems, neural networks, tree classification, fuzzy logic, genetic algorithms, etc. These methods can be employed to solve rock mechanics and ground control problems associated with the highly complex nature of rock masses and ground conditions. A current study at the University of Alabama focuses on development of an artificial intelligence system for real-time interpretation of the data collected from longwall monitoring stations, and development of an early warning system for prediction of undesired conditions and prevention of longwall-mine instability problems. This paper describes a ground control management system using UALSAS (The University of Alabama Longwall Stability Analysis System), which is being developed to facilitate maintenance, on-line analysis, prediction, and includes an early warning system. A detailed framework of computer algorithms and their applications are also discussed. The successful application of these artificial intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1995

By R. D. Beard

Puerto Rico lies within the remnants of a deformed Cretaceous island arc system in the northeastern Caribbean. The Island can be divided into three broad geologic provinces: the Central Volcanic-Plutonic Province (Lower Cretaceous to middle Eocene), and the Northern and Southern Limestone Provinces (early Oligocene to middle Miocene). Known precious metal deposits are generally small and occur in veins and shear zones within Lower and Upper Cretaceous volcanic and plutonic rocks. Some Tertiary igneous rocks are also mineralized. Selected indications of disseminated lithology-controlled mineralization could represent larger deposits. Associated metals in some deposits include copper, zinc, and lead. At present, tax policies, population density, political outlook, and lack of proven significant precious metal deposits discourage the establishment of a metal mining industry.

Jan 1, 1993

By T. Bartnitzki, N. Fietz

"INTRODUCTION For a long time now automation has been state of the art in production engineering and chemical engineering. The advantages of automation are, for instance, higher reliabilities of production processes, higher product qualities as well as capacities and improved safety conditions for the personnel. In contrast, many operations in mining are still conducted manually by machine operators instead of autonomous control units. One example for this is the excavation of underground hard coal which is still executed with aid of human perception. The Institute for Mining and Metallurgical Machinery (IMR) has been working on possibilities for sensor-based automation of mining machinery for many years now. Thereto the focus is set on the implementation of common material analysis techniques into ruggedized conditions as a basis for automation. Laser-induced breakdown spectroscopy (LIBS) for instance is an atom emission technique which enables the determination of the elemental composition of a sample. After introducing LIBS this paper will give an overview on dust formation during the cutting process. With the illustration of a few examples the challenges in determining dust concentrations specifically such of cutting processes are explained in further detail. The final chapter will outlay the possibilities and challenges in utilizing cutting-induced dust for the automation of shearer loaders. LASER-INDUCED BREAKDOWN SPECTROSCOPY LIBS Fundamentals LIBS (laser-induced breakdown spectroscopy) is a contact-free method for analyzing materials in any state of aggregate. It pertains the atom emission techniques and is based on the generation of plasma, inducing avalanche ionization on the surface of a solid material or any spot in a gas or aqueous solution. With sufficient background information on the expected elements and an additional calibration, this method can determine all present elements not only qualitatively but also quantitatively. However, this method cannot be utilized for determining the molecular composition of materials – if this feature is required a complementary method such as Raman analysis needs to be added. (1, 2)"

Jan 1, 2015

By Robert W. Leonardson

The Questa Molybdenite Mine provides a unique opportunity to study the geochemical dispersion of various hydrothermal events, utilizing drill hole analyses. Numerous post-ore factors have altered the primary ore-related geochemical dispersions to the present day configuration, e. g. dikes, faults, hydrothermal convection cells, and weathering. Due to the interaction of an andesitic volcanic pile with the silicic-alkalic generated volatiles, the geochemical haloes of the Goat Hill deposit demonstrate a marked divergence from the classic Climax-type molybdenite ore body. Certainly, however, the similarities to the Climax-type ore body are apparent as potassically-rich fluids have invaded the highly reactive country rock.

Jan 1, 1984

By Surendra K. Mishra

Metallic and oily components are the major contaminants of industrial wastes. Underground burial and incineration have been the commonly practiced methods of waste management. To provide a relatively more permanent solution, different processes have been developed. In addition to reviewing these processes, potential of using flotation as a process to treat hazardous metal and oil contaminated wastes is discussed in this paper.

Jan 1, 1989

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By Colin J. Booth

Hydrogeological impacts of active longwall mining were studied at two sites in Illinois. At the site with the more transmissive sandstone aquifer, aquifer permeabilities increased an order of magnitude due to subsidence. Piezometric levels declined with subsidence due to increased porosity, and ahead of mining due to a transmitted drawdown. Levels recovered rapidly at first and fully over two years. At the site with the less transmissive aquifer, impacts were similar except that recovery has been limited. Local aquifer enhancement through increased yield can occur, but only where the aquifer is transmissive enough for recovery.

Jan 1, 1986