Search Documents

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

By M. Shriwas, F. Calizaya

"Controlled recirculation may be considered as a beneficial means in mines of cold climate, where heating of air is required, and in deep or extensive mines, where cooling of air is required. Controlled recirculation can be designed by proper sizing of the booster fans with respect to main fan. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario shows lesser buildup of methane concentration than the former one. INTRODUCTION The controlled recirculation is designed purposefully to allow a partial fraction of used air that increases the air velocity due to increased quantity of air and consequently allows effective dilution of contaminants to improve local ventilation condition at the working face. It can be designed by proper sizing of booster fan with respect to main fan in a ventilation network. Controlled recirculation may be categorized as crosscut, in-line or combined system based upon the configuration of the booster fan locations in a district ventilation network. Research on controlled recirculation has shown numerous benefits of controlled recirculation especially in deep or extensive underground mines, where further heating or cooling is required (Calizaya 1990; McPherson 1993 and Jones, 1987). However, fear of buildup of concentration has misled the mining communities to view the controlled recirculation as a hazard and deprived the mining industry to derive benefits from recirculation. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario result shows the less buildup of methane concentration than former scenario result."

Jan 1, 2016

By X. Wu, M. G. Karfakis, K. Y. Haramy, B. T. Brady

A quantitative evaluation of damage caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations that are subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain-energy buildup are identified and investigated. A methodology for the evaluation of strain-energy accumulation caused by, an overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude (ML), which depends on the seismic energy transformed from the stored strain energy that is released when the roof fails. A particle-velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and the damage area agree well with field observations.

Jan 1, 1997

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials will borrow strongly from terrestrial experience but will also involve the necessity of handling literally unEarthly feedstocks, reagents and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed, with the production of rocket propellants, life-support fluids, structural metals and refractories as the goal.

Jan 1, 1994

By M. Beus, S. Stewart, S. Iverson

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods and better hang-up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mockup of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were compared Loads on an active ore pass chute were measured

Jan 1, 2000

By John F. Schat, T. William Thompson

Laboratory data on the time-dependent compaction of porous rocks are presented, and various attempts to model this behavior are described. These lead to a discussion of the problems that arise in using laboratory data to estimate long-term effects. A method is suggested for combining laboratory data with information from the geologic record to estimate long term effects.

Jan 1, 1986

By R. Y. Wan, J. D. Miller

Thiohydrometallurgical systems including thiosulfate, thiocyanate and thiourea have been stud- ied as alternative liriviants for the leaching of gold. Research and development of thiohydrometallurgical technology has been prompted by environmental concerns with the use of cyanide and problems associated with the processing of difficult-to-treat ores. These thiosystems have some chemical similarities, enabling gold to be leached in a practical oxidizing environment. However, the solution chemistry of the thiosystems is complicated due to instability of the thioreagents and many other reactions which occur during the gold leaching reaction. In this paper, interference reactions of selected metal ions and sulfide minerals are examined in order to understand important aspects of solution chemistry which control the stability of the thioleaching reactions. Applications using thioreagents as lixiviants for oxide and refractory gold ores are presented.

Jan 1, 2005

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By B. Nyman

A lot of work is in progress to improve copper recovery by leaching-solvent extraction-electrowinning (L-SX-EW). At Outokumpu the focus of attention is on SX equipment development as a result of which a new mixing-settling technology, the Vertical Smooth Flow (VSF) has been introduced. Using helical stirrers in the VSF mixers a more gentle and uniform contacting can be obtained than in the mixing compartments of the low-profile design. The benefits of Outokumpu's new approach are an essential decrease in organic losses and in aqueous in organic entrainments. Separate pumping using a smoothly pre-contacting "Dispersion Overflow Pump" (DOP) is a key feature of the VSF design. The scale-up of this pump as well as the VSF mixers are shown to follow simple mathematical relationships which also have been confirmed by full scale experiments.

Jan 1, 1995

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By John C. Wangaard

A method of raising by use of a cage has been used with considerable success at the Cary Mine, Hurley, Wisconsin, on the Gogebic Range. The Cary Mine is owned by the Odanah Iron Company, Pickands, Mather and Company, Managers. This method is known to have been used previously at Tennessee Copper and probably in other districts. The Cary Mine was engaged in deepening the main shaft from the 34th to the 37th level. To accomplish this, and to facilitate development, a ventilation shaft 930 feet north of the main shaft was sunk from the 34th to the 37th level and crosscuts were driven on the 35th, 36th and 37th levels to the main shaft location, These levels are at 200 foot verticalintervals. All of this work was done in granite and the majority of the workings were not timbered. The next step was to get a raise through from the 37th to the 36th level, and from the 36th to the 35th level, which would later be stripped to full shaft size. Several methods of raising were considered including double-compartment cribbed and two single raises interconnected at regular intervals, but the cage method was chosen as it appeared to be a safe and efficient operation. The method in general consists in the use of a drill hole between levels through which to pass a hoisting rope to raise and lower a light cage.

Jan 1, 1958

By M. J. Mrugala

Typically the conventional pillar design methods consider the behavior of the pillar alone. In such analysis the contribution of the associated roof and pillar is not considered. The focus of this paper is a study of pillar behavior in the context of interaction between a different rock material sequence in the associated roof and floor. The finite difference element code FLAC (1)is used to perform modeling of pillar response to various stratigraphic sequences.

Jan 1, 2003

By T. Foster

The continuous operation of decanters in the mining industry relies heavily on the use of synthetic flocculants. Today, as plants seek to lower production costs by increasing throughput it is necessary to obtain optimum performance from the flocculant. Factors affecting such optimization include charge and molecular weight selection, and efficiency of mixing the highly viscous polymer solution with the feed slurry. Beyond maximizing dilution of the solution, the last factor is often ignored. This paper describes a series of calculations, based on fundamental transport theories, that have been used to describe flow conditions within decanter feed wells and to help select flocculant addition points. Examples are shown for the case of hydroxamated polyacrylamide flocculants in the Bayer Process, where proper selection of the addition points can result in lower flocculant dosage and better control of the decanters.

Jan 1, 1996

By Herbert S. Richey

Two hundred years ago next April, our forebears embarked upon the difficult path to national independence. They succeeded, and shook off the yoke of foreign domination. In the ensuing two centuries, the country was mobilized several times to protect that political and economic independence from foreign domination. These efforts were also successful. Thus, as we stand here on the threshold of our third century of political independence, we can thank previous generations and congratulate ourselves for establishing and maintaining the world's oldest republic. Now -- once again -- the United States faces the challenge of foreign intervention into our economy. This time the battleground is resource avail- ability. America has been blessed with enormous resources. Whether we speak of minerals or timber or water or "amber waves of grain," this nation has benefitted from a resource base that is the envy of the world. This asset, coupled with a political system that permitted us to develop it, has been the physical backbone of our independence. Without the economic independence that this resource base has given us, the political independence we fought for would have been tenuous, at best.

Jan 1, 1975

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Both share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be -implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control call is considered a form of insurance to enhance the value of an exploration or mining project.

Jan 1, 1997

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By Haydn H. Murray, Fred G. Heivilin

The "Hormite Group" was proposed for palygorskite (attapulgite) and sepiolite for their complex magnesium silicate composition and elongate crystals (Martin-Vivaldi and Robertson, 1971). These minerals occur in close association with each other and more complex structural variations may exist (Bailey, 1972). In 1862 Savchenkov used the name palygorskite to describe a mineral from the Palygorsk locality (Hay, 1975), near the Ural Mountains. Ovecharenko and Kukovsky (1984) mention that when mountain leather deposits were prospected in the Palygorsk Division mine it was assumed this unusual mineral was a variety of asbestos. Early mineralogists used the terms "mountain cork" or "mountain leather" when referring to palygorskite. Robertson (1986) mentions that it appears palygorskite was known since Theophrastus&apos; time, ca. 314 BC. J. de Lapparent used "attapulgite" for clays from Attapulgus, GA, and Mormoiron, France, because he thought them different from palygorskite, but the two types were proved to be the same (Bailey et al., 1971). The name attapulgite is still used for the Florida and Georgia deposits when the crystal length to diameter ratio does not exceed 10:1(Merkl, 1989). Georgia palygorskite clays are of much shorter length compared to classic palygorskite. In 1847 Glocker first used the name sepiolite which was called "Meerschaum" by Werner (1788) and Hauy (1801) namedit "Ecume de Mer." Brochant (1802) described low density and white magnesium silicates adding the name Talcum Plasticum and Ecume de Mer. In the Meigs-Attapulgus-Quincy district palygorskite (attapulgite) commonly occurs in two distinct forms referred to as short length palygorskite (Meigs Member) and long length palygorskite (Dogtown Member) (Merkl, 1989). Long length palygorskite crystals (> 10 pm) are rarely observed in the Meigs and Dogtown Members, but when present are in association with dolomite crystals. The short length form is usually less than 2 pm in length and has a low magnesium content whereas the long length form has a high magnesium content and a length greater than 2 pm. The distinctions in morphology are not only important because of the relationship to the origin of the deposits, but also in relation to activity in causing membranolytic activity related to data on palygorskite samples from 9 locations ranging from relatively inert to active in work reported by Nolan et al. (1989). The > 10 pm lengths amounted to only 51 of 17,401 fibers sized. The shortest lengths (< 0.5 pm) were relatively inert. This study pointed out that surface activity, morphology, and chemical differences may be distinctly different within the definition of palygorskite, or for that matter for any individual mineral so that health and other properties must be measured because the name alone does not necessarily indicate uniformity. Palygorskite (attapulgite) fuller&apos;s earth was first sold for drilling mud in 1941. The market for this use expanded slowly and has maintained a level of 7 to 10% of the total US production during the last few years. Most of the fuller&apos;s earth sold for drilling mud comes from the southern part of the Meigs-Attapulgus-Quincy district of Georgia and Florida. Palygorskite clays produced in this area are superior to most other fuller&apos;s earth for mud used in drilling salt formations, but because of high water loss, they are inferior to bentonite where the rocks drilled contain no saltwater. According to Oulton (1965), more than 90 different grades of fuller&apos;s earth are produced. Some of these grades are used for pharmaceuticals designed to absorb toxins, bacteria, and alkaloids; for treatment of dysentery; for purifying water and dry cleaning fluids, dry cleaning powders and granules; for the manufacture of NCR (no carbon required) multiple copy paper; for the manufacture of wallpaper; and as extenders or fillers for plastic, paint, and putty. Fuller&apos;s earth mined near Ellenton, FL, was used for making lightweight aggregates for the construction of concrete barges during World War I1 (Calver, 1957). Still other uses of fuller&apos;s earth and its suitability for uses in new products are outlined by Haden, Jr., and Schwint (1967), Haden, Jr., (1972), and Haas (1970). One special use of fuller&apos;s earth is as a carrier of platinum catalysts that are made in the United Kingdom from sepiolite clays mined in Spain. Other uses of sepiolite fuller&apos;s earth (Chambers, 1959) are similar to those of the palygorskite (attapulgite) type mined in the United States.

Jan 1, 1994