Search Documents

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By Christopher Haycocks

Successful ground control is an essential part of all viable underground mining operations. To a large extent ground conditions influence the choice of mining methods, percentage and cost of extraction, and often the degree of safety that can be achieved. Utilizing the computer for ground-control planning offers great potential under many diverse conditions as not only are computations facilitated, but also details of the often complex geologic and structural framework of the mine can be readily stored and retrieved. Two basic approaches have been developed for applying the computer in solving ground-control problems. The first uses an analytical method, such as the finite element technique, for solving a specific problem. The second is more general and involves storage of geologic data and application of general design equations. The latter has found wide application in stratified deposits. It is the purpose of this chapter to describe both approaches as they are used for improving the ground-control aspects of mine planning.

Jan 1, 1979

By Jan W. Oberholzer, Jan J. L. Du Plessis, Gerard Appelman, Andrzej M. Wala

The use of on-board scrubbers on continuous miners is an important aspect in efforts to reduce the amount of dust that heading workers are exposed to. As part of the CSIR:Mining Technology's research programme to combat dust, a collaborative project with the University of Pretoria was conducted to evaluate scrubbers. Based on fundamental parameters that were identified to play a role in determining the efficiency of scrubbers, a protocol for testing scrubbers in the laboratory environment, as well as the working section, was established. Tests on various prototype scrubbers were conducted in the laboratory environment. These tests proved some of the fundamental premises according to which scrubbers were designed. By testing some of the newer scrubber types underground, insight into the effect of alternative design aspects on scrubber efficiencies was obtained. The importance of the factors which play a role in reducing the amount of dust in the air is illustrated, as well as the role which other non-design factors play in the reduction of dust levels.

Jan 1, 1995

By Kumara S. Rachamalla

Mineral activity in Ontario represents an annual production in excess of $4 billion. The Ontario government encourages the mining industry to undertake mineral development through grant programs and incentives offered by mineral resource taxation. Computers are playing an increasingly important role in improving productivity in the administration of incentive programs and the Mining Tax Act in Ontario. This has meant speedier processing of grant applications and tax returns which is resulting in a streamlined approach to incentives and taxation in Ontario. The use of computers has resulted in significant contributions to key areas of concern such as assessment of mining tax returns, analysis of the changes, if any, to the Mining Tax Act and modeling of the Ontario Mineral Exploration Program (OMEP). Implementation of state-of-the-art technology such as Local Area Networks (LAN's), fourth generation languages and integrated micro-mainframe information processing has resulted in improved productivity as well as lower costs. As a result, the respective services provided to the mineral industry by these two programs are now delivered in an efficient and cost-effective manner utilizing the latest available computer technology.

Jan 1, 1986

By P. Muduli, Y. Xi, T. M. Yegulalp, A. J. Arias

A short review of current practices and recent developments is followed by a description of a newly developed approach for solution of the optimum, ultimate pit limit problem. The new approach utilizes network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson (1956). Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method automatically includes several optimal solutions based on a predetermined number of benches to be included in the analysis.

Jan 1, 1994

By E. A. Barrett, L. L. Rethi

Throughout all segments of the United States mining industry, 163 independent contractor employees were fatally injured between 1990 and 1997. Factors that contributed to these injuries were identified after reviewing descriptive information contained in Mine Safety and Health Administration fatality reports for each of the incidents. Thirty-three unique contributing factors were identified and multiple factors were noted for each fatality. Those most frequently discerned were "failure to follow `standard operating procedures"', (35% of the fatalities), "poor positioning of employee" (26% of the fatalities) and "failure to maintain equipment" (23% of the fatalities). Contributing factors were then associated with the accident and job classifications of the victims. Factors having the highest frequencies in the top five accident classifications where most fatalities occurred were as follows: powered haulage - "failure to maintain equipment"; machinery - "poor positioning of employee"; slip/fall of person - "inadequate fall protection" and "failure to wear safety line"; electrical - "equipment contact with power line"; and falling/rolling/sliding rock - "poor positioning of employee. " Among the job classifications in which most fatalities occurred, leading contributing factors were as follows: truck driver - "failure to follow standard operating procedures" and "poor positioning of employee"; laborer/utility man/pumper - "poor positioning of employee"; mechanic/ repairman and welder - "failure to follow standard operating procedures." Recommendations for utilizing contributing factor information as a basis for safety training are proposed. Training programs may be developed that inform independent contractor employees of factors which, in the past, have contributed to fatal injuries in their job classifications. Then, by combining this information with contributing factors identified in "related" accident classifications, a truly focused training intervention that addresses very specific workplace hazards may he developed.

Jan 1, 2002

By James S. Browning

In 1975 bituminous coal and lignite production in the United States reached an all-time high of 637 million tons, an increase of 6 percent over production in 1974. The output, valued at $11.9 billion f.o.b. mines, was produced at 5,100 mines in 24 states (6). Coal mining is the largest mining industry in Alabama. Production from Alabama's mines in 1975 was over 21 million tons, and present projections forecast a steady increase in production, with tonnages almost doubling by 1985 (5). Of the total quantity of coal produced, about 16 million tons were consumed in electric power generation and the remainder was used for metallurgical coke production, extraction of chemicals and petroleum based products, and power for industry. The fact that 75 percent of Alabama's power is generated by burning coal attests to the importance of this fossil fuel to the State. Approximately 14 million tons of coal were produced by strip-mining methods in Alabama during 1975 and about 7 million tons were produced by underground mining during the same period. Surface mining is expected to continue at about 14 million tons per year, but by 1980 underground coal mining is expected to increase to about 25 million tons (3). About 7 million tons of surface-mined coal in Alabama is subjected to some means of washing or cleaning. The methods used are screening accompanied by heavy media separation, jigging, tabling and flotation. Some of the simpler approaches employ screening and jigging, or tabling. Except where flotation is used, the screen undersize fraction (finer than 0.25 inch) is rejected, with the result that 10 to 15 percent of the coal is lost. Thus, in the State of Alabama an aggregate of about 1 million tons of coal is wasted annually in the fines which are impounded from treatment of surface-mined coal. The use of the Humphreys spiral to concentrate fine coal was practiced as early as 1947. At that time the Hudson Coal Company (1) used Humphreys spirals to concentrate anthracite fines. In 1950, the use of spirals to treat fine-size

Jan 1, 1977

By Ray E. Harris

All of the major raw materials (silica, soda ash, limestone, and feldspar) needed to manufacture most grades of glass are found in Wyoming. Additional advantages for the manufacture of glass include the state's geographic location, a well-developed transportation network, a favorable tax structure (no corporate or personal-income tax), and low energy costs. Inadequate local markets and prohibitive transportation costs to other markets have been the major obstacles to developing a glass industry in Wyoming, the least- populated state in the nation. The Rocky Mountain region only recently became a major market for glass, especially for the Colorado Front Range and Utah's Wasatch Front. Currently, changing costs of the production of glass, an increased market for con- tainer glass in the Colorado Front Range, and innovative production and transportation ideas (e.g., production of selected types of glass and bulk shipments of specification-glass pellets) favor developing a glass plant in Wyoming. Thus, the Wyoming State Geological Survey (WSGS) and other state agencies have been conducting studies and contacting investors in an effort to attract a glass-manufacturing plant to the state. Between 1987 and 1993, three locations of silica-sand and -rock deposits were studied in Wyoming (Cassa, Plumbago Creek, and John Blue). Funding was provided by the WSGS operating budget and local and state Department of Commerce economic- development grants. The reports on these areas were released between 1988 and 1993. In 1988-89, a California-based company conducted additional drilling and feasibility studies and prepared to construct a glass plant in Cheyenne, using the Cassa silica source. However, due to losses incurred by some of their other investments, the company did not proceed. In 1997, the Wyoming Science, Technology, and Energy Administration (STEA) contracted a market study for glass manufactured in Wyoming, using information provided by the WSGS. The STEA contacted several major glass producers, and a major glass-producing company began feasibility studies in January 1998, for the construction of a glass plant. In June 1998, bids to supply brown beer bottles to the Budweiser brewery northeast of Fort Collins, Colorado, were submitted by at least two companies that were considering glass-plant sites in Wyoming.

Jan 1, 1999

By Geoff Beale

In terms of their hydrogeology, most open pit mines can be divided into three categories. There are mines that occur above the water table, mines that extend below the water table in high permeability rocks and mines that extend below the water table in low permeability, tight formations. Mines that occur above the water table do not experience major ground water seepage. It may some- times be necessary to construct in-pit trenches and sumps to remove water from precipitation. But dewatering or enhanced drainage measures are typically not required. Open pits that extend below the water table in high permeability rocks find it cost-effective to pump from dewatering wells. This is done to lower the water table below the working pit floors, creating dry or depressurized conditions in advance of mining. If the rocks in the mining area are homogenous, complete drainage of the entire mining area may be achievable by pumping from wells. In this case, it is not necessary to consider drain- age enhancement. However, there are many open pits and excava- [ ] tions that can lower the water table using conventional wells, but for which drainage enhancement is also an integral part of the dewatering system. The Sleeper Mine in Nevada is an example of this. Hydraulic layering at Sleeper has prevented downward drainage of water as the main water table is lowered. In addition, there are many mines that have areas of low permeability wall rocks that do not freely drain as the surrounding water table is lowered. Ground water seepage also creates difficulties in mines that occur below the water table but for which lowering of the water table using conventional wells is not feasible because of the overall low permeability of the rocks. The volumes of water involved may be small. However, it is necessary to deal with all of the water inside the pit as mining proceeds. It is not possible to dissipate pore pressures in the wall rocks in advance of excavation.

Jan 1, 1997

Traditional finance theory recommends discounted cash flow (DCF) analysis as the tool to value mineral properties. Yet, the calculated values by this method are usually lower than the market value. Finance theory also advises us to develop an undeveloped project immediately if its net present value is positive. Most projects are, however, only developed when the economics are highly favorable. This paper uses insights from option-pricing theory to explain these divergences between market behavior and finance theory and presents simple modifications to discounted cash flow analyses that will lead them to produce correct valuation and development timing advice.

Jan 1, 1999

By J. M. Applegate, C. L. Morgan

Introduction In the same way that a blueprint communicates informa¬tion about a structure, a systems architecture should provide information that guides the construction and implementation of a computing system. Taking the blueprint analogy a step further, a plot plan can also show where, in the "bigger picture," a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: • the primary purpose of computer-based systems rela¬tive to particular tasks or operations, • the relationship of the systems to each other and an indication of their interaction and dependencies, • the relationship of the systems relative to the organiza¬tion and its objectives, • indications of where IS/IT resources can best be allo¬cated to support the organization and • the overall context in which new systems and technolo¬gies can be assessed for both their impacts on current systems and on the organization itself. In theory, a well-designed systems architecture should allow an organization to focus its resources on those aspects of its business that matter most, thus, leveraging investments in information technology to a competitive advantage. In addition, the way that a computing systems architecture is represented should be un¬derstandable to non-IT staff, and it should be eas¬ily recognized by the people it supports. This pa¬per attempts to show that a meaningful systems model exists and that its applica¬tion to mining can achieve the desired results. The following discus¬sion is based on the au¬thors interpretation of a concept referred to as the computer integrated manu¬acturing (CIM) model, as developed by Allen-Bradley. An inherent strength of the CIM approach is that the model combines aspects of business-reporting structures with the manufacturing process itself. What results is a systems frame¬work that is aligned with relevant business processes and is, therefore, easier for non-IS/IT personnel to interpret. The successful application of the CIM model can be seen in a large number of both discrete and process-manufacturing facilities throughout the United States. This paper provides a brief overview of the CIM model and then describes how the model can be applied at a conceptual level to the mining industry. Finally, this paper proposes an extension to the CIM model that the authors believe will make it easier to understand and apply. CIM model As shown on Fig. 1, the CIM model begins with the most detailed levels of process equipment and works its way up to the highest level of consolidated financial reporting. Systems at each level are characterized by common attributes, users, time frames, etc., providing a clear picture of their interac¬tion. Further analysis of the relationships between systems and between levels provides insight into the opportunities for integration. Regardless of the industry or processes involved, the CIM model provides a framework in which the characteristics of systems and the data they manage can be predicted based on the nature of the business function they support. In general, as data moves upward from the lower rungs of the CIM model, it changes from de¬scribing the physical na¬ture of a process to describ¬ing its financial aspects (e.g., from productivity to cost). The time frame to which data applies also transitions from a very short duration, perhaps only milliseconds, to financial or regulatory reporting time frames that may span years. In a simi¬

Jan 1, 2000

By M. J. McPherson, P. Mousset-Jones, J. Banik, F. Calizaya

Friction factors or coefficients of friction used to estimate the resistances of mine airways are, in the main, estimated from empirical measurements made in other airways considered to be of a similar geometry and type of lining. A somewhat more analytical approach, although still based on empiricism, is to estimate the ratio of the average height of the asperities to the hydraulic mean diameter of the airway (e/D ratio) and then to employ the Moody Chart or one of the equations that have long been established to represent the [coefficient of friction v Reynolds number curves] on that chart. Unfortunately, the Moody Chart and corresponding equations are based on pipes of uniformly distributed (sand grain) roughness whereas the asperities that exist on the surfaces of mine openings are frequently highly irregular both in their size and distribution. This is considered to be a major cause of discrepancies that have been found between coefficients of friction by the Moody Chart and those actually measured in mine airways. The work described in this paper examines an alternative method of estimating coefficients of friction for rough natural surfaces with uneven sizes and distribution of surface asperities. The technique utilizes the relatively recent developments in fractal analysis. A fractal dimension is determined from the topography of the surface. This has been correlated to coefficient of friction for a scale model of a mine airway. Further work is being carried out in actual mine airways. However, at this time, it appears promising that the fractal method may allow coefficient of friction to be predicted for given types of strata and method of roadway drivage.

Jan 1, 1993

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By M. Sengupta

Vast reserves of oil shale occur in the Green River formation in Colorado, Utah, and Wyoming. The room-and-pillar mining method is applied to flat-lying sedimentary deposits. Important elements in mine design include mine orientation, vertical location of the mining zone, selection of roof horizons, room span and pillar size, barrier pillar size, panel dimension, and layout of mains and submains.

Jan 1, 1988

Early experiences suggested autogenous mills were difficult to operate and consumed substantially more energy than conventional rod/ball mill circuits. As our understanding has increased and the technology has matured this perception has changed to the point where most new comminution circuits are ag/sag based. In addition many operators have replaced existing conventional circuits with this technology. The JKMRC has been studying ag/sag mills for over 20 years. During this time it has amassed what is probably the single largest and most detailed data base of pilot and full scale mill operations in the world. This has been used to help develop and refine its cur- rent commercially available mathematical model of ag/sag mills. A decade of its application has greatly helped simplify both design and operation of ag/sag milling circuits as well as helping to promote the effective use of recycle crushing, secondary crushing and closed-circuit operation. This paper describes the development of ag and sag milling in terms of our understanding and the evolution of the technology. In addition the application of mathematical modelling and simulation in designing and operating efficient circuits is described with the aid of practical examples.

Jan 1, 1998

By Michael J. Martinson

A powerful methane explosion in the mid-shaft pump station of a main service and ventilation shaft killed several persons on the station; more workers were killed when a mancage travelling down the shaft fell to the shaft bottom under a pile of broken concrete slabs from a brattice wall destroyed by the explosion venting into the shaft and a tangled mass of twisted steelwork from the equipped compartment. The newly-commissioned shaft serves a recent extension of an established mine on the Orange Free State (OFS) goldfield in South Africa. After outlining the circumstances in which the paper was written, and reviewing the nature and extent of the methane hazard in OFS mines, the paper describes the physical layout of the shaft and summarises evidence given by witnesses at the official inquiry concerning events prior to the explosion. No attempt is made to apportion blame for the incident.

Jan 1, 1989

By Craig M. Sams

Dry grinding circuits and factors influencing the selection of the most appropriate grinding system for a given ore selection are discussed. Comparisons of the drying, grindability, installed costs and operating costs are presented for several grinding systems.

Jan 1, 1994

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By Jindrich Fiala, Jirí Kout

The paper contains knowledge that have been achieved when the problem of airflow temperature and humidity changes prediction in mine airways was investigated. The substance of physical processes has been consistently applied. The methods of dry-bulb and wet-bulb temperatures calculations can be applied in any type of mine airway. The exceptionality of auxiliary ventilated airways is in the original solution of so called losing air flowing when a ventilation pipe is leaky. The combination of aerodynamics and thermodynamics solutions enable to determine climatic conditions on projected workplaces with a sufficient accuracy.

Jan 1, 1991

By R. L. Pozzo, A. S. Malicsi, I. Iwasaki

The electrochemical nature of mineral-grinding media interaction in the wet grinding of one and two sulfide mineral ores was investigated with regard to the flotation behaviors of the minerals. Two iron sulfides (pyrite and pyrrhorite) and mild steel were used to represent the sulfide minerals and the grinding media, respectively. Galvanic currents in two- and three-electrode combinations under abrasive and non abrasive conditions were correlated with the floatabilities of these minerals under corresponding conditions.

Jan 1, 1991