Search Documents

By R. Simon

Strain-burst phenomena are generally characterised by sudden releases of energy in a volume of highly stressed rock. Strain bursts are encountered in situations such as crown pillar bursts during cut-and-fill mining, face bursts at development headings cord floor bursts in deep shaft sinking. This paper describes a simple two-dimensional linear elastic FE modeling approach that leads to the calculation of the energy-release rate (ERR) and the total energy storage rate (TESR) in the rock-mass around the openings. The merits of using such energy parameters in the analysis of strain-burst problems for identifying areas of high energy release/storage are discussed through a case stud v. However, much site-specific back analyses are needed to better understand how strain bursts and energy parameters are interrelated.

Jan 1, 1999

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By L. G. Austin

The paper summarizes the current state of development of simulation models for SAG and FAG mills, and gives the results of recent investigations of the physical processes occurring in autogenous grinding. The breakage process is treated as the sum of three regions of breakage actions: normal breakage caused by nipping of particles between media (steel balls or pebbles); abnormal breakage caused when the particle or lump is too big in relation to the media to be readily nipped; self-breakage resulting from the chipping fracture and abrasion of the tumbling action of rock lumps. Each region of breakage action has associated specific rates of breakage and primary progeny fragment distributions.

Jan 1, 1989

By L. Reyes-Bozo, R. Ginocchio, A. Godoy-Faúndez, C. Sáez

Relationships among mining industry, society and environment have been historically complex due to its environmental impacts. In the Chilean mining industry, repetitive and small spills of fuel during maintenance of machinery have been adsorbed by desert soils and sawdust to control environmental pollution. The froth flotation is the main technology to recover specific mineralogical species from sulphide ores. Flotation reagents are expensive and representing an environmental risks due to its physics properties. Our objective was to investigate the feasibility of applying bioremediation as a cost-effective alternative technology to physical-chemical treatments and to evaluate the efficacy of biosolids as foaming agents. Our results show that the bioremediation is feasible by use of the autochthonous microbial communities and biosolids could be used as new environmental-friendly organic reagents. This research discloses a sustainable bioremediation process and industrial ecology model based on these two successful cases.

Jan 1, 2011

By A. G. Journel

The regionalization of tungsten grades at the deposit represents an ideal case for anisotropic hole-effect variogram modelling. The modelling technique is presented step-by-step and the consequences of the model on block kriging are indicated.

Jan 1, 1982

By P. Venkatsubramanian, D. R. Maneval

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1987

By P. Zhang

The results of bench-scale testing of five flotation processes for the separation of dolomite from phosphate are discussed. Each process is compared in terms of phosphate recovery, MgO content of the concentrate and reagent consumption. Water quality was found to play a major role in the performance of these processes. The effect of water hardness, in addition to other parameters, are discussed.

Jan 1, 1997

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By A. G. Sciulli, G. P. Ballock, K. K. Wu

This paper discusses common environmental problems associated with coal refuse disposal. It suggests design concepts to minimize potential hazards. Discussion focuses on site selection, embankment design and construction, site preparation, facility operation, abandonment, and reclamation. It emphasizes measures that should be adopted in the design phases and during construction of the facility. Recommendations are also made concerning special problems, including seepage, ground water contamination, and mine sealing.

Jan 1, 1987

By Lane White

Environmental regulations have become a decisive factor for many minerals industry operations. Managers face new liabilities as a result of environmental laws, and restrictive permitting requirements for new projects make mine development an increasingly difficult proposition. An abundance of federal, state and local environmental laws and regulations already confront on-going minerals operations, and complex new legislation and rule-making is always in progress. Acronyms and initials like RCRA, CERCLA, SARA and EIS become as familiar as reserves, tons, grades and recoveries. The growth of such regulation has created a new category of professional employees - environmental scientists and engineers-whose presence will influence minerals production activity from now on. The disciplines of environmental science and engineering are still being defined. While these definitions are being worked out, companies in the minerals industry have responded by hiring people with professional experience in existing disciplines and training them to their special needs. An environmental consulting industry of substantial proportions has developed to offer expertise where producing companies may not find it economic to hire full-time professionals. The mining schools have responded by introducing environmental course work, but these programs have yet to supply a significant number of environmental professionals to the minerals industry. To gain some perspective on where minerals producers now stand in their hiring of environmental professionals, ME recently surveyed 20 companies, with questions about how they go about the business of managing environmental compliance. Twelve companies re¬sponded to the survey, and the results

Jan 1, 1991

By M. H. Weinecke, B. P. Faulkner

This paper discusses the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last 10 years. Many claylike materials, such as coal fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce commercially salable LWA.

Jan 1, 2003

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By C. Treworgy

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Jan 1, 1997

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By J. D. Scott

This paper consists of a review of the development and application of spherical charge blasting at Inco Metals Company. Topics will include the Livingston Strain Equation, the field data required for its use in full scale operation, the type of ground in which mining has been carried out, explosives in use and their characteristics and finally, an overview of actual production applications. These applications include Primary Stope Mining, Secondary Mining Against Fill, Mining a Faulted Ore Zone and Drop Raise Blasting. INTRODUCTION Crater blasting in itself has been in use for over twenty years, but only recently has the technique been combined with a spherical size charge to form the Vertical Retreat Mining Method. This article endeavours to put the Livingston Strain Equation in a practical light, to describe several actual hard rock applications, and the results achieved in each case. THE LIVINGSTON STRAIN ENERGY EQUATION C.W. Livingston put forward the following equation as a standard means of determining the optimum burden required for full crater production blasting. The constant "E" is included in an attempt to recognize secondary breakage caused by strain waves.

Jan 1, 1981

By David M. Mchaina, Allan E. Hall, Siegfried Rohr, J. D. Botsford

Incidents associated with secondary dust ignitions in the mining of massive sulphide ore deposits are of major concern in Canadian underground metal mines. During stope or development blasting, a highly concentrated cloud of sulfide dust is created and may be ignited, resulting a secondary explosion which releases a considerable volume of sulphur dioxide and possibly other sulphur gases. The consequent pressure, heat and toxic gases can result in loss of life, significant damage to equipment and loss of production. These losses are expensive and should be prevented. Explosions of this type have occurred at the H-W mine of Westmin Resources mainly in the development headings and cut and fill stapes. This paper presents the results of a study conducted at the H-W mine to compare dust sampling methods for explosivity tests. The associated benefits and pitfalls of each sampling technique are examined. The investigative work conducted to develop and test preventive and control methods against sulphide dust ignitions is also discussed. The techniques which will minimize the risk of sulphide dust ignition in metalliferous mines are outlined. A review of current preventive and control measures practised at the H-W mine is also presented.

Jan 1, 1989

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016

By H. Ehnes

"“Industry 4.0” – “Mining 4.0” - perhaps you have already heard of these terms? These keywords signify the next stage of industrial production. The internet and production technologies are growing closer together. Machines can communicate with one another, wherever they may happen to be located. The “Internet of Things” is the appropriate term. But what does SAFETY 7.0 mean? It is both brand new and traditional at the same time. It also has to do with the success of companies, with efficient production. And yet there is a great deal more at stake. It has to do with our lives and our safety – the supreme commodity in this world. What exactly SAFETY 7.0 means, what the number 0 stands for and the meaning of the number 7, and what this all has to do with mining will be explained in the following article. Mining is a fascinating undertaking. Mining is indispensable for a country’s economic development, whatever that may concern: infrastructure, energy supplies or raw materials for industrial production. Mining has brought forth many technological developments and innovations that can currently be found in our daily lives. Mining is impressive, grandiose and repeatedly fascinates mankind with its immense dimensions. Miners throughout the world still work hard and, for this reason, are bound to one another in a special way. In mining, every man looks out for the other; you have to be able to rely on each other. That creates a strong bond. The other side of the coin is that mining and disasters belong to normality in the media and thus also in our perception. Accidents at work and even catastrophes occur in mining, quarries, or raw material operations almost on a daily basis somewhere in the world. They are often associated with extremely serious injuries, or even a fatal outcome, for the miners affected and, in turn, dramatic consequences for the families of those involved. It could be in China, India, Russia, or somewhere in Africa, Asia or America – it mostly does not happen in front of our door or in our neighbour- hood. Perhaps because of this in the daily concert of negative headlines, we do not register these catastrophes any more in our minds. We write them off under the heading “Nothing special”, since there are, day in day out, more terrible news items about wars, civil wars, famines, or ecological disasters. Things only really change if there is a dramatic number of deaths or when we are personally affected, close by in the vicinity, or can witness the rescue action live. In Europe, these three mining disasters in particular have recently generated media resonance:"

Jan 1, 2016

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By P. D. Nora, M. G. Ranade

A statistically designed pot grate-kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables - bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate - were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a plant trial. The target firing temperature at the Empire plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets.

Jan 1, 1987