Search Documents

By S. L. Zhu, Brij M. Moudgil, J. L. Pinault

Prompt neutron activation probe (PNAP) was evaluated to determine chemical composition of phosphate rock slurry in-situ. The technique was able to precisely analyze Ca, Si and H using a 252Cf source. Direct measurement of P and Mg was not accurate due to interference by the rare earth elements associated with the Florida Phosphate Rock. The solids loading, particle size distribution and flotation reagents present in the slurry had no significant effect on the accuracy of the measurements. The technique was found to be reliable also under industrial conditions.

Jan 1, 1993

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By P. Tsang, S. S. Peng

Mine floor failures, such as floor heave and floor buckling, occur frequently in underground coal mines where soft mine floor exists. The types of failure can usually be classified into two categories; shear punching failure and tensile failure. A model based on the Winkler's elastic foundation is proposed in this paper for floor stability analysis. The model considers material properties of floor strata, in-situ horizontal stress, pillar size, entry width, and configuration of multiple-entry system and predicts stress conditions in the mine floor based on given in-situ mining and geological conditions, as well as deformation of the mine floor. This information is used to predict possible failures of mine floor by comparing the strength of mine floor with its stress condition. The validity of the model is verified by in-situ data described in this paper.

Jan 1, 1992

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By Joseph Cervik

Methane drainage methods can be broadly classified as surface or underground. Surface methods make use of vertical and slant holes. The underground method discussed in the present paper involves horizontal drilling from shaft bottoms and from locations along the periphery of mines. Every foot of hole drilled in coal from under- ground locations is productive and gas flows increase as hole length increases. Therefore, underground techniques have a great potential for producing large-volume flows of methane. Pumps to dewater the horizontal holes are not necessary because gas pressure forces the water out of the hole. Methane can be recovered through the use of a simple and inexpensive gas-water separator. Hydraulic fracturing, which has been used successfully to stimulate gas flows from vertical holes, has not proved practical in the case of horizontal holes.

Jan 1, 1980

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By Stanley W. Ivosevic, Mark E. Emerson

Introduction Metals exploration activity is moderately intense in the US despite the 1981-82 recession in the mining industry. Although exploration expenditures are significantly less than the 1981 peak, quality and goal orientation of current exploration are high. Major foreign and domestic mining companies as well as nonmetal companies had been attracted to invest in minerals in the US. Its capital markets, political stability, and open-door policy are attractive for hard mineral explo¬ration, particularly in the West. The approach was to either acquire fully or partially developed ore bodies through merger and acquisition, or to fund large scale exploration programs in search of bulk-tonnage deposits. The acquisition avenue has not proved the panacea envisioned for overcoming lack of substantive mineral development. Nor has the decentralized approach to exploration that was adopted proven cost-effective. The emphasis on gold, to the exclusion of all other commodities, raises questions regarding the direction of exploration in the US for the rest of the 1980s. Overview More than 300 companies are active in metals exploration in the US. These range from established, well-known domestic and foreign corporations to hurriedly incorporated, unknown companies financed by having promoted mineral prospects or occurrences of questionable quality. Junior companies tend to be oriented toward property entrepreneurship, rather than the development of minerals resources. These companies have helped maintain mineral lands from prospect to production by holding blocks of property intact during periods of exploration inactivity. This was done through promotional efforts, even though few properties that attracted major venturers proved to have real merit. Exploration objectives of senior and junior exploration companies currently embrace only a few commodities. Arranged in approximate descending order of priority, these are: precious metals; base metals in monometallic or polymetallic deposits; strategic metals, such as tungsten, tantalum, and tin; unconventional commodities, such as diamonds; ferrous metals; and commodities such as beryl, zeolites, and barite. Prospectors are important in searching for these targets. In the US, where they have been financed by major and junior companies, prospectors have proven a useful and low-cost means of locating gold prospects (e.g. the Alligator Ridge property in Nevada). The tenacity and persistence of independent prospectors have been factors in discovering properties rejected or overlooked by professional geologists (e.g. Lornex mine in British Columbia). This has been realized by the provincial government that grubstakes bona fide prospectors. Exploration interest in commodities has always been cyclic with price. Gold is one of the few metals that has experienced a price increase of such magnitude to warrant attention. The potential for realizing adequate operating margins for the Nevada open-pit "no-see-um" gold deposits is great. The present declining gold price, however, may indicate that this emphasis on gold, to the exclusion of other commodities, is shortsighted. Mining companies have been the last to react to price increases, opening new mines based on unrealistic market expectations. A scenario could develop where plummeting gold prices bring recession to the gold industry, as lately occurred in uranium, molybdenum, and copper. US Exploration Climate The US is attractive for exploration due to its strong mineral po-

Jan 4, 1984

By Jan M. Mutmansky, David R. Kalasky

Computer simulation continues to be one of the most successful analytical applications of computers in the mining and mineral processing industries throughout the world. Through simulation, managers and engineers can explore the impact of new technologies, equipment designs, plans and operating strategies to improve their operations. It is not uncommon for a single simulation application to provide a quick payback of analysis expenses (within weeks or months) yielding long-term financial and operational dividends. The paper will present a summary of the types of software systems that are available for use on PCs and other computer systems. Support software for curve fitting, statistical analysis, and optimization of simulation models will also be presented. Methods of leveraging simulation efforts through networking and coupling of software systems will be discussed. Finally, the trends in simulation in the mineral industries will be analyzed. Areas of strength and weakness of simulation will be discussed along with the usefulness of commercial general-purpose and custom-writ- ten simulation packages. The future possibilities for simulation in the mineral industries will be outlined and predictions on trends for the future will be presented.

Jan 1, 1996

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By J. Finch, W. Petruk, R. G. Pinard

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections to characterize a mill product and determine the apparent mineral liberation. It was found that a representative polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly, individual screened fractions are not representative of the sample because minerals are partitioned during screening, and the quantities of soft brittle minerals are increased in fine grained fractions, whereas the quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (one Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analyzing each fraction and combining the data. Somewhat less accurate data would be obtained by analyzing a series of screened fractions that have a wider size range of particles (five Tyler size ranges).

Jan 1, 1987

By Christopher E. Johansson, William J. Kohr, John W. Shield

Heap biooxidation is an economical means to treat refractory sulfidic ores. However, air flow limitations are a major obstacle in commercialization of this technology. Geobiotics, Inc. has developed a new process for heap biooxidation of sulfide ores that renders the ore more susceptible to bacterial oxidation. In this process, air and liquid flows in the heap are greatly improved by first removing clays and other fine particles from the ore. Gold bearing sulfides are recovered from the removed fines and separately biooxidized. Column biooxidations were conducted on two refractory sulfidic ores from which the fines had been removed in order to improve air flow through the column. Gold recoveries increased from 46% to 90% for a mill grade ore and from 52% to 80% for a low grade ore after biooxidation. Fines and clays in these ores had precluded whole ore heap biooxidation from occurring. This new process addresses the most significant problem of large scale heap biooxidation.

Jan 1, 1996

By M. Saunders Macdonald

A number of open pit gold mines in Nevada extract ore from areas below natural groundwater elevations, necessitating dewatering and some method of disposal of the extracted water. These open pits extend well below the water table, with associated dewatering volumes greater than 10,000 gpm. Some mines, with large volumes of dewatering water to manage, have constructed re-infiltration basins to re-introduce dewatering water to the groundwater system some distance from the pits. This paper presents an overview of the state of the art of re-infiltration projects, including the permit process for such projects in Nevada, and the necessary engineering considerations.

Jan 1, 1996

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008

By B. Govindarajan, T. C. Rao, J. P. Barnwal

A simple modelling methodology has been proposed to predict the performance of industrial coal flotation circuit based on the observations made on the actual performance. The solid content in the tailings of the coal flotation circuit has been identified as a lode-star to predict the performance in terms of yield and ash content of the concentrate. The modelling parameters are directly measurable.

Jan 1, 1995

By A. B. Szwilski

The mineability and coal processing costs are influenced largely by the structural and physical properties of the coal seam. The mining process involves coal cutting, pillar support, crushing, and floating. A correlation between the rank, ash content, and coal strength/stiffness is discussed. The coefficient of variability of rebound tests on the face of various coal seams are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1988

By H. B. Oblad

The WEMCO® SmartCell™ flotation machine is a continuously-stirred tank reactor in which solids are suspended in water and are contacted with air. The reaction is particle flotation resulting in the separation of valuable material from gangue. The effects of several operating variables on the flows of water and air and on motor power were measured. A miniature magnetic flowmeter was installed in the draft tube that allowed measurement of the water flows into the rotor. This work has led to a better understanding of machine function which will lead to improved performance and better operation. General equations for optimization, design, and scale-up were inferred.

Jan 1, 2002

By Dennis A. Beiter, William J. Francart

Barometric pressure changes have been an important consideration in the sealing of mines, especially in the case of mine fires. These changes are caused by storm fronts and regularly, on a daily basis, by atmospheric heating and cooling. In many cases, anticipation of these fluctuations in a mine sealing operation or recovery can be an important consideration when scheduling activities. The barometric pressure changes create pressure differentials across sealed areas, inducing airflows which may create explosive mixtures of mine gasses, cause intensification of fires, and create irrespirable atmospheres outby seals. These effects of barometric pressure fluctuations on mine fire sealing and recovery operations are discussed. Data available from the National Weather Service is also discussed as a tool for predicting barometric pressure changes.

Jan 1, 1997

By Clifford J. Lewis

The role of calcareous minerals in that area of the environmental improvement program involving the control or elimination of sulfur oxide emissions is discussed, and a new concept in gas scrubbing, rendering possible the use of calcareous rocks more extensively for this purpose, is presented. Calcareous rocks are defined as the more common limestones, consisting essentially of calcium carbonate and magnesium carbonate. The effect of magnesium carbonate on the reaction rate of limestones and lime toward sulfur oxides in aqueous scrubbing systems is pointed out. The relative economics of lime- stone versus lime as aqueous scrubbing reagents for sulfur dioxide are indicated.

Jan 1, 1974

By S. K. Kawatra, T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and the recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically constructed very tall (30 to 40 ft) to limit the effects of back mixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug flow. In this work, horizontal baffles were shown to improve the performance of a 6 -ft laboratory-scale flotation column treating a poorly floatable coal. Tests with variations in the baffle positions showed that baffles are needed both above and below the feed inlet to achieve the greatest benefit. Tracer tests with a fluorescent dye in water showed that baffles reduce the amount of feed water entrained in the froth at any given coal recovery.

Jan 1, 1996