Search Documents

By k. Osei-Boakye

This paper presents the calibration of a real-time aerosol monitor, the TSI DustTrak?, to the NIOSH 5040 method being used by the Mine Safety and Health Administration (MSHA) for compliance enforcement evaluation. The standard NIOSH 5040 instrument for compliance evaluation of diesel particulate matter (DPM) has an inherent time lag of up to two weeks for laboratory processing of sample results. Therefore, providing the underground mines with a means of quantifying DPM conditions in real-time, will enable them to efficiently and effectively manage DPM levels to ensure compliance with the regulated limit.

Jan 1, 2009

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 150 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey (USGS) canvass of producers. Domestic production in 2005 was estimated to be 24.8 Mt (27.3 million st) valued at $176 million. This was based on a preliminary survey of the common clay and shale industry. The leading producer states, in decreasing order by tonnage, were North Carolina, Texas, Alabama, Georgia and Ohio.

Jan 1, 2006

By R. B. Elver

The St Lawrence Seaway, a deep-water canal system between Montreal and Lake Ontario, was opened for navigation on April 25, 1959. Prior to the opening of the new Seaway, small boats known as canalers and a few deep-sea carriers, primarily from Norway since World War II, were the only ships able to journey past Montreal into Lake Ontario through the old Canadian St. Lawrence canal system. Thus it was necessary for many tons of bulk and general cargo to be shipped all-rail to and from Atlantic ports or to be transhipped to and from canalers. With the opening of the new Seaway, large Great Lakes bulk carriers and a much larger percentage of the world's shipping fleet are now able to sail directly from the sea to the heart of industrial North America. In this paper, the historical events leading up to the construction of the Seaway and the physical nature of the Great Lakes transportation system are briefly reviewed. Following this, an attempt is made to evaluate the effects of the new Seaway on Canada's mineral industry. Because the Seaway has been in operation for only one season, this paper must be considered only an interim report. Because of the importance of the Seaway to iron ore, this commodity will be dealt with in detail, although the effect on other mineral commodities such as coal, petroleum, nonferrous ores, iron and steel will be mentioned. At this time the author wishes to thank the various company and government officials who provided both factual information and critical opinions.

Jan 1, 1960

By S. H. Brown

In our work as health physicists*, we do a lot of public speaking and interaction with the public on issues related to development of uranium mining and milling (?uranium recovery?) in the US. Understandingly, the public has important concerns about this. Accordingly, this paper is presented in a ?question and answer? format in which we have tried to capture what are some of the most common concerns we hear from citizens and address them. We have attempted to do so based on the best scientific information we have, representing information well documented in peer-reviewed scientific literature and consensus positions from both national and international scientific standard setting bodies and related committees. We have included some of the more important of these scientifically-based references to support the information provided. Practical space limitations prevent completeness in this regard in some cases. Visit the Health Physics Society?s web site or feel free to contact me directly for additional references, information or detail ? Steve Brown. The health physicist?s primary objective is to manage the beneficial uses of ionizing radiation while protecting workers and the public from potential hazards. For more information on what a health physicist is and on the Health Physics Society, visit the Society?s web site at www.hps.org.

Feb 23, 2014

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By J. Wickens

Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine?s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine?s history, the metallurgical testing, the flowsheet and discusses design considerations. KEY WORDS: process plant, flash flotation, leaching, SMD, stirred media detritor

Feb 27, 2013

By Fitzhugh T. Lee

Results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Paleocene Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit highwalls in the Fort Union Formation within the study area have adequate short-term stability, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and stability conditions could become critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Jan 1, 1977

By K. V. Raj

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in open-pit mines is relatively new. Modeling the actual pit geometry of an open-pit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an open-pit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in open-pit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions, and turbulence modeling parameterization. An appropriate mesh selection is critical. A detail discussion of the meshing of the domain of an open-pit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (?-e), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an open pit and some of the approaches adopted to address these challenges.

Feb 27, 2013

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By W. X. Wang

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification pro-gram for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field. Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1996

By K. Biswas, F. C. Felipe

Paste backfill, because of its colloidal or water-holding properties, does not produce run-off water when placed underground. Paste backfill is generally, prepared from relatively low water content, full mill tailings with a certain proportion of ultra-fine particles and mixed with cement, thus producing early and better strength. Mill plant discharge tailings and other materials available at or near the mine site such as sand, aggregates or waste rock are used as blending materials in the mix design. This study investigates the influence of the above-mentioned blending materials on the mechanical characteristics of paste backfill, as well as the grading, shape, specific surface area, mineralogy and workability of the different mix design.

Jan 1, 2000

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is over-compacted. Research has shown that excessive compaction in replaced growing media is detrimental to establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky has developed test cells on reclaimed sites at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. The impact of organic soil supplements on soil physical properties and tree survival rates is also being evaluated at the site. The organic soil supplements being evaluated include application of hardwood bark and application of straw and mulch. Each test cell has been planted with various species of trees, and for the first two years, data have been collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data are currently being correlated to determine how ripping and the application of organic soil supplements affects the relationship between soil compaction and tree survival rate.

Jan 1, 2002

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By I. G. Gonçalves

For most industrial minerals, the color is directly associated with economic value. In terms of physics, the principal property that defines the term ?color? is the intensity of light reflected (or transmitted) by an object over the visible band, comprehended between 400 and 700 nm. This reflectance spectrum serves as the starting point for a variety of color-describing factors, the most common in the mineral industry being the brightness (TAPPI, 1977 and 1986) and the L*a*b* system (HunterLab, 2008). Quality specifications for mineral products are usually based on these colorimetric parameters. This market is becoming increasingly more selective and demanding over the quality of raw materials and alongside the traditionally controlled characteristics, such as particle size distribution and chemical composition, a trend exists towards the establishment of increasingly more strict specifications for the optical properties of these materials. This is due to the fact that most plants consuming these industrial minerals incorporate them into products in which the visual appearance is controlled. For these plants, most of them being the manufacturers of plastics, paper, paints, and ceramics, variations in the color of mineral materials result in difficulties to achieve the right color in the final product. Therefore, these plants set strict specifications for colorimetric parameters such as whiteness and yellowness, as well as colorimetric coordinates like L*, a*, and b*. For the manufacturer of industrial minerals, this translates into difficulties simply because many of these parameters are usually alien to the tradition of the mining industry. The main quality parameter in the kaolin industry is brightness, which is a weighted average of reflectance values over the range of 400-510 nm (TAPPI, 1977). Due to the lack of a better property, producers tend to use brightness to also assess the quality of the in situ ore and along the processing operations. However, the unprocessed kaolin is often accompanied by ?contaminant? minerals. For Brazilian kaolins, which are the object of this study, the most important contaminants are hematite (Fe2O3), goethite (FeOOH), and anatase (TiO2). Each of these contaminant minerals has a distinct color and behaves differently during the processing of the kaolin ore. Hematite and goethite in particular are particularly strong pigmenting agents and at concentrations as low as 100 ppm they can make the difference between a high-quality white pigment product for paper coating and waste material. As each Fe-bearing contaminant has a different color and responds differently to processing operations (for example, magnetic separation, chemical bleaching, selective flocculation, and/or flotation in the case of kaolin), the in situ brightness tends to show a poor correlation with the brightness of the final product. Brightness measurements are sometimes complemented with X-Ray Fluorescence (XRF) analysis of Fe and Ti, but the total oxide content provided by XRF is also poorly correlated with product quality because Fe may be in the form of goethite, hematite, or inside the crystalline structure of kaolinite. Thus, a more robust technique capable of distinguishing each mineral phase is desirable. Diffuse reflectance spectroscopy has been used to analyze iron oxide/hydroxide content both qualitatively (Torrent and Barrón, 2003; Liu et al., 2011) and quantitatively (Jiet al., 2002 and 2006). These authors correlate slopes and inflection points at characteristic absorption bands with oxide/hydroxide content in natural soils. The approach presented here involves the extensive use of the Kubelka-Munk (K-M) theory, which has been used for color matching (Schabbachet al., 2009 and 2011) and particle size determination (Otsuka, 2004) in a simplified version. Unfortunately, the scattering constant S is very difficult to measure for dry powders, because the equations require a thin layer of material. Attempts have been made (Gonçalves and Petter, 2007, and Gonçalves, 2009) but the experimental errors tend to be high. Thus, this paper aims to develop a tool for the quantification of contaminant minerals in kaolin based on the K-M theory without resorting to measurements over thin layers. This tool is based on a new two-constant approach, which takes into account differences in scattering between materials over the whole measured spectrum. The experimental dataset consists of the reflectance spectra of mixtures between a bleached kaolin and synthetic Fe pigments.

Feb 27, 2013

The Montgary pegmatite is located at Bernic Lake in the southeastern Manitoba pegmatite district. 'It has a complex internal structure with several contrasting mineral assemblages. The pegmatite contains a number of potentially valuable miners including spodumene, amblygonite,. lepidolite, zinnwaidite, pollucite and beryl.. The distribution of each of these within the pegmatite is related to the internal structure and controlled by a specific mineral assemblage. Parts of the pegmatite contain a high concentration of spodumene. The pollucite occurrence is of unique character and is one of the largest known deposits of this mineral. The pegmatite is still-like in attitude with a maximum dip of about 15 degrees. Its contents with the amphibolitic wall rocks are sharp and tourmalinized. Mineral assemblages present include perthite-plagioclase-quartz-muscovite, spodumene-microcline perthite-plagioclase-quartz-muscovite, cleavelandite-lithia micas-quartz, quartz-amblygonite, albite, lepidolite, pollucite, and quartz assemblages. The occurrence and relationships of these are described and possible relationships between attitude and internal structure are discussed. Many features of the pegmatite suggest that the deposit formed by crystallization and differentiation of a pegmatitic fluid in a restricted system. These features are discussed. The nature and occurrence of the pollucite, lepidolite and albite assemblages are such, however that it is difficult to visualize them resulting from such a system. These assemblages may be of later replacement origin. The source of the, late, alkali-rich replacing solutions may be unmixing of soda and the rarer alkalis (lithium, rubidium, caesium) from earlier-formed silicates in a manner analogous to the unmixing of soda feldspar in perthites. Various aspects of this hypothesis are examined.

Jan 1, 1959

By V. E. Housman

EPA's Office of Solid Waste (OSW) is developing a program, under Subtitle D of the Resource Conservation and Recovery Act (RCRA) to regulate the management of non-coal mining wastes. In May 1988. OSW produced a "Strawman", which is a working document that is precursor to a proposed rule. OSW has been working closely with environmental groups, industry, and States to solicit comments and feedback on the mining waste program. OSW currently plans to release a second "Strawman" in early 1990. A proposed rule is tentatively scheduled to be published in the spring of 1991.

Jan 1, 1990