Search Documents

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

Let’s start off with your assessment of the mining industry. Today, the status of the mining industry is stronger than it has been over the previous few years. While mining continues to be a major part of the world’s economic foundation, the industry is gaining strength due to rebounding metals and minerals prices. And now, with these rising prices and the changes the industry instituted during the years when mining-related commodities were selling at low prices, our stronger, more productive and internationally competitive industry should flourish. Mining remains an essential business and the industry is far ahead of the game when it comes to the trend of globalization as a key to sustained growth. Also, the industry continues to realize increased productivity through technological innovations. And an increasing number of countries are moving towards capitalism, which opens doors for exploration and mining within their borders. After looking at all of these factors, I believe that the mining industry will only continue to gain momentum in the future.

Jan 1, 2004

When defining a ?megaproject,? one need only to look at Seattle, WA?s State Route 99 Alaskan Way Viaduct replacement project. This $3.1-billion project is one of the largest of its kind in the world, and includes the use of the world?s largest tunnel boring machine (TBM). However, for as large as the Alaskan Way project is ? especially given the size of the TBM being used ? there are several other megaprojects underway around the world. Each has its own challenges that require innovative design techniques and financing arrangements, as well as variations on established tunneling technologies. So it was that 266 tunneling and underground construction professionals ? owners, contractors and engineers ? convened in Seattle in November for the Cutting Edge Conference on Megaprojects. This was the second joint meeting between the Underground Construction Association of SME and the North American Tunneling Journal. The first joint conference took place in April 2012 in Miami, FL and attracted 238 attendees. A third joint conference, to be held in 2014, is in the planning stage. The key reason Seattle was chosen as the site of the megaprojects conference is the Alaskan Way Viaduct project. Before the conference began, many of the attendees were able to visit the project and get a close look at Bertha, the Hitachi Zosen earth pressure balance TBM that is boring the tunnel. In addition, the conference included an exhibit that attracted 20 industry suppliers, up from 10 the previous year in Miami. The 25 presentations during the two-day conference covered all aspects of the tunneling and underground construction of megaprojects. Topics included the Alaskan Way Viaduct project; considerations for procurement and contracting; political risk, financing and insurance; international megaprojects; risk and risk sharing and project delivery. Each session concluded with panel discussions.

Dec 1, 2013

By F. H. Mertens

The costs of an open-pit operation can be classified according to the following hierarchy : -overall cost of production (per ton of ore) -costs of basic operations and functions -costs of auxiliary operations -costs of machines and equipment -maintenance costs. Production cost is a measure of the open-pit mine performance and should be the final target of the management control. It is also a measure of the share of the mine in the processing stages.

Jan 1, 1990

By Ping Zhang, Xu Ma

Perturbations arising from mining operations significantly affect the stability of rock masses, and the influences aggerates with the rapid increase of mining-operation depths during recent years. The subsurface structures with major discontinuities subject to seismic hazards resulted from the shear-slip behaviors of rock masses. In order to identify the shear-slip regime of discontinuities and calculate seismic moment and seismic energy involved with shear-slip behaviors, we use discrete element modeling to study the shear slip failure along discontinuities in an underground mine. The recorded characteristic and properties of sub-contacts in DEM provide a basis for computing and visualizing the temporal and spatial distribution of seismic moment and seismic energy with mining operations. We computed the seismic energy and seismic moment using the numerical modeling method and the analytic method. We compared the result of summing seismic energy and seismic moment from the subcontacts of numerical models and the result of the analytic method. We confirmed that this tool can be used in comparative analyses. We also found that seismic moment and seismic energy, associated with shear stress drop and shear displacement increase, accumulate in the vicinity of major discontinuities. Mining operations at a greater depth cause greater changes of seismic moment and seismic energy, leading to a higher risk of inducing seismic hazards. Quantifying seismic potential using discrete element modeling can greatly facilitate the investigation of instability of geological discontinuities and thereby can help estimate the potential of seismic hazards.

Jan 21, 2023

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

In recent years, slag, a residue from pyrometallurgical processes, has become more attractive in circular economy frameworks to increase the efficient use of resources throughout the life cycle of steel products and help in the reduction of carbon emissions. Its applicability is strongly dependent on the particle size, and therefore, the optimization of breaking processes should be approached by increasing the knowledge of the dynamics of slag to promote fracture. Increasing the knowledge on themechanical response ofmanganese slag opens up the potential for the development of cost-effective numerical models, e.g., constitutive models based on inverse engineering calibration frameworks or digital twins. In this study, rate-dependent tests of manganese slag have been performed using a split Hopkinson pressure bar device for testing its dynamic mechanical response. In order to obtain information about the crack initiation and fracture process, 2D ultra-high speed imaging was implemented with a sampling frequency of 663,200 fps for diametrically loaded specimens. Full-field deformation measurements using digital image correlation (DIC) techniques showed a staggered fracture process where failure points on mechanical response curves vary due to the internal events happening in the material. Localized frictional occurrences and inertial effects acting inside the pre-cracked matrix have a strong effect on the global mechanical response, and therefore, a great variability of strengths was obtained.

Nov 3, 2023

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without king reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county mad and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Feb 24, 1997

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from prototypes to production-ready applications, the operating performance of the haul road will become critical to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width. This will, therefore, generate potentially significant reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and its associated deterioration rate, is predictable and manageable, based on the materials used to construct the road and the maintenance interventions to be carried out on the road.This article presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined partly from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this article, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images that are analyzed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration.Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management and, although the quality of mine roads have probably"

Jan 1, 2015

By I. Gombköto, G. Földing, G. Mucsi, B. Csoke, J. Faitli, B. Kovács

This paper summarizes the main achievements of our previous project entitled "Development of a technological system producing quality guaranteed fly-ash based binder". Furthermore, this study deals with the laboratory experience of lignite fly ash utilization for two different goals. On the one hand the fly ash was tested as a binder; on the other hand it was investigated as an underground mine backfill material. Considering the first goal, the utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of relationship between the degree of activation of fly ash and the strength of the obtained concrete. The results confirmed that this hydraulic binder is suitable for construction of stabilization and capping layers or base layer. Regarding the backfilling application, this paper presents laboratory experiments, their results including settling tests, hydraulic permeability and strength measurements and dense slurry technology related results.

Jan 1, 2011

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements which appear in the periodic table. The group consists of 15 lanthanide elements along with yttrium and scandium (Table 1). They share many similar properties, which is why they occur together in geological deposits. Although commonly referred to as rare, they are really quite common; the reason they are perceived as rare is because it is not common to find them in commercially viable concentrations. These metals are critical to advanced technology, ranging from smart phones to global positions system (GPS) receivers, medical devices and jet engines. They are critical in green, high-tech and defense industries (Fig.1 and 2). Although there have been increasing efforts to find alternative supplies, these efforts have been complicated by the pollution that rare earth mining and processing creates. To extract rare earths minerals from mined ore is a complicated and costly process. The ore is first mined through normal mining process, the bastnaesite, which generally contains a number of minerals of little value, is first removed through a floatation process. The bastnaesite containing the REEs is further separated into their respective pure forms in a separation plant using acid and various solvent extraction separation steps. Each element has its own unique extraction steps and chemical processes. At times, these elements, in the form of oxides, will require reprocessing to achieve ideal purity. The last steps would be to further process into metals first, then alloys for various applications. The entire process takes approximately 10 days. The mining and processing of REEs, if not carefully controlled, can create environmental hazards. This is one of the reasons the Mountain Pass Mine in California was closed down in the 1980s.

Dec 1, 2013

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

This one day field trip is sponsored by the Denver Region Exploration Geologists? Society, May 14th 2009. The trip highlights major geologic features and some notable uranium occurrences along the north-south mountain-basin boundary southwest of Denver and continuing north to Fort Collins, Colorado. Uranium deposits visited include sandstone?hosted roll front type and polymetallic veins hosted in metamorphic rocks. A replacement ?episyenite? type occurrence is considered via description and hand samples but is not visited owing to logistical constraints. Recovery methods addressed include underground mining and in-situ leach recovery. Samples of Precambrian basement rocks, deposit host rocks, uranium ore samples, and ore polished sections viewed by reflected light microscopy will be available. A road map showing the locations of the stops serves as the front cover of this field guide. The Robinson episyenite-hosted occurrence (not visited) is labeled as Stop 6. A stratigraphic column is provided which shows the position of the host rocks at each stop (Figure 1-1).

Jan 1, 2009

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Paul H. Johnson

Resource Engineering and Development, Inc. is desigining and building a portable 150 to 225 tpd, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, highgrade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on 18 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981