Search Documents

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003

Clean Diesels fuel-borne catalyst, Platinum Plus, helps improve fuel economy for all engines up to 10 percent while reducing particulate emissions by up to 25 percent. When used with a simple diesel oxidation catalyst, particulate emissions can be reduced by 30 to 50 percent. The use of Platinum Plus enhances combustion in the cylinder, burning fuel more completely. This reduces CO2 and other greenhouse gases and lowers total operating costs by improving fuel economy.

Jan 1, 2007

The General Purpose Simulation System (GPSS) is a computer simulation language that has been used for simulations of open pit haulage operations since the 60's. It is easy to learn, simple to use, and has a block-diagram structure that is amenable to load-haul systems. However, due to its lack of flexibility, there are situations where another language should be chosen. This paper reviews the characteristics and capabilities of both GPSS and FORTFAN with regard to open pit shovel and truck simulation. The relative advantages and disadvantages are highlighted and a case study presented along with comparative results from two computer models (one written in GPSS and the other written in FORTRAN).

Jan 1, 1986

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985

By Hassan Madani

Kushk lead-zinc mine is located in central part of IRAN. The mine is owned by Bafgh Mines Co., which is a nationalized company. Exploration results show that ore occurs in the area that extends for 800m length and 180m depth. The approved, probable and possible reserves of the mine is 900,000 tons, 1,120,000, tons and 1,450,000 tons respectively with average grade of 17.7% zinc and 4.3% lead. The total annual output of the mine all was by underground mining, is in the order of 100. 000 tons. The main entry to the mine is via an inclined shaft with a cross-sectional arp of 8 m2, length of 263m which dips at 20°. The ore is mined mostly by sublevel stopinq method. The major difficulty in ventilating the mine was that related to spontaneous combustion of pyrite, which was more serious in some parts of the mine than others. In order to reduce this risk, a new ventilation system for the mine was designed, using 4 exhusting fans.

Jan 1, 1991

By Hiroshi Himura, Shoichi Tsushima, Hiromi Goshima

This paper reports the construction of an environmentally-friendly tunnel in sedimentary soft rock near a residential area. The main tunnel, which will be used as the Onmawashi-Koen (Park) Regulating Reservoir, is a large-scale tunnel with a cross sectional area of 254.0 m2 and a lengthof 577.3 m, excavated using such support as shotcrete, rockbolts and steel H-sections. Since the large main tunnel is excavated in sedimentary soft rock, it is necessary to keep the stability of the tunnel face and the crown and to prevent surface settlement. A top heading with a length of 50 m is therefore driven as a pilot tunnel to observe the ground behavior during excavation, and to obtain information on the geological conditions based on which type of support structure is determined with consideration given to the results of field measurements and numerical analyses.

Jan 1, 2001

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By Jean-Pierre Nossereau, Allen J. Hulshizer

The main thrust of this paper covers the design, installation techniques and experience associated with the installation of eleven 1.5 m (4'-11") and three 2.87 m (9'-5") diameter shafts in 15 to 23 meters (50 to 75 ft) of water over 1.6 Km (a mile) out in the Atlantic Ocean. The approach implemented, permits the use of pre-fabricated shaft linings and incorporates a safe dry-tap method for connecting the offshore shafts to tunnels driven blind from deep land shafts over 4.8 Km (3 miles) away. This tunnel-shaft system is a unique venture employed at the Seabrook Nuclear Power Station to meet plant cooling water requirements.

Jan 1, 1981

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Donald C. Violetta

During 1963 more than 200 million tons of coal was consumed by the public utility industry. Ash residual, from the burning of this coal has caused disposal problems. In order to prevent air pollution, dust collection systems have been installed to suppress the fine ash emitted from boilers before it is discharged into the atmosphere. The collected ash, called fly ash, must be removed from the dust collection facilities and disposed in some manner, usually at a substantial cost to the utility. Many years ago fly ash disposal was not a serious problem because the demand for power was relatively low and coarse coal was burned on stoker type traveling grate machines. The low burning rates utilized on these grates did not produce large quantities of air-borne coal ash while the mechanics of this system of burning resulted in a clinkered residue of cinders. Both of these conditions resulted in the production of only small quantities of fly ash. As the demand for electricity increased, a method of burning pulverized coal was developed and was introduced to the public utility industry in 1918 at Milwaukee, Wisconsin.1 This method of firing was considered a significant advance in steam electric generation as it (1) permitted the use of coals that could not be economically fired by other methods and (2) has generally resulted in improved efficiency, greater generating capacity and lower costs.2 The utilization of larger generating units using pulverized coal substantially increased the quantity of fly ash which resulted in a' more severe disposal problem.

Jan 1, 1966

By William A. Faust

At Gold Fields' Chimney Creek Mine, major reviews of the reclamation and closure plans are done concurrently with the annual mine planning required for budget preparation. This review includes identifying and scheduling reclamation work that can be done within the next few years and development of associated costs. Longer term mine, leach pad and waste dump development are examined to take advantage of any design changes that can reduce ongoing reclamation or closure requirements and reduce costs. The success and cost effectiveness of past efforts are continually evaluated to determine the best methods for reclamation.

Jan 1, 1992

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By D. Elroi

This paper addresses the sharing of 2D and 3D data between GIS and mine planning software. Two-dimensional (2D) data, and now three-dimensional (3D) data as well, can be formatted such that both types of software can use, exchange, and display the same datasets. This increases the ability to share data between such groups as environmental, exploration, and mine planning. It overcomes shortcomings of mine planning software in areas of open database connectivity, spatial analysis, and data input and output. It also helps to overcome shortcomings of GIS software in the areas of geologic modeling, three-dimensional interpolation, and visualization.

Jan 1, 1998

Sedimentation is used to clarify process effluents or to thicken process slurries. The sedimentation cycle of a suspension is presented as a settling curve. This curve is simply a plot of the height of the interface between the settled suspension and clear liquor versus time. Figure 1 shows a series of graduate cylinders which contain a suspension at various stages in its settling cycle. Cylinder 1 shows the suspension completely mixed at time zero. After a brief period of time (see cylinder 2), the suspension is observed to settle from its initial height Ho to height H1, leaving behind a volume of clear (or turbid) liquor, called the supernatant. The interface between the supernatant and suspension is termed the mud line. It is also possible to distinguish at the bottom of the cylinder a layer of sludge representing solids which have settled from the suspension. The interface between it and the suspension is called the sludge line. The sludge line moves upward in the cylinder.

Jan 1, 1992

By B. J. Timmons

Depending upon which of two letters describing the theme of the session I chose to honor, the subject choices because either one or three. They were: "Applied Research and Exploration and Discovery" or "Applied Research in Exploration and Discovery." The final choice; to partially ignore both of them. That minor difference in meaning may be appropriate here, inasmuch as very minor research/exploration differences may also have profound impacts on discovery. To further set the stage, I consider myself an Industrial Minerals geologist, and more specifically primarily associated with basic construction materials crushed stone and sand & gravel. My remarks will apply primarily to those materials. Therefore, when the discussion instructions included emphasis on beneficial aspects (to name a few): "drill target definition; elimination of ore potential; ore forming environments; alteration studies, and isotope analysis," problems became apparent. Evidently, and although this was a form letter, the drafters of that letter had no idea what was involved in research for a construction materials source. My task may be great.

Jan 1, 1995

By Adolf J. Jonaitis

Outokumpu developed TankCell flotation cell technology beginning in 1990, following 35 years of successful flotation cell experience and application. In 1994, Outokumpu proved favorable operating success of 100-m3 (3,500-ft3) TankCells for porphyry copper and zinc flotation. In 1995, evaluation of a 150-m3 TankCell led to the successful application of these large cells in several operations. More than 350 TankCells of 100 m3 and larger in volume have been installed and are in operation. Key features of the Outokumpu TankCell design will be described. In addition, discussion of operating data from various metallic mineral flotation operations worldwide will be presented. Large flotation cell development continues today, with operating cell volumes of up to 160 m3 (5,500 ft3) in operation.

Jan 1, 1999

By Jon C. Yingling

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will be intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder throughflow to avoid production bottlenecks.

Jan 1, 1992

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016