Search Documents

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By YONGQIONG YANG, Ning Wang, CHONGGUANG LUO, LI ZHU, Hanjie Wen, SHENGJIANG DU, Hannian Gu

Niobium in kaolin clay from the Late Permian sequences was reported in the range of several hundreds of micrograms per gram and was considered as a potential resource for its high concentrations and large areal distribution. Ti-bearing minerals associated with kaolin clay were identified as the main host phase for niobium in some case studies. However, the correlation between the concentration of niobium and titanium is poor, and the types of Ti-bearing minerals and modes of occurrence of niobium are not clear. Typical kaolin clay samples from the Late Permian sequences from southwest China were characterized, and the final products derived from kaolin clay sample were investigated using XRF, ICP-MS, XRD, SEM, and TEM (EDS). The results reveal that there were three types of TiO2 mineral phases in the clay samples: (a) massive TiO2 minerals and (b) aggregates of nano TiO2 minerals did not contain niobium while (c) granular TiO2 minerals were the source of niobium from the EDS analysis. The granular TiO2 minerals included anatase and rutile, both of which were the sources of niobium in kaolin clay in the current study. The findings are of great theoretical implication for source and origin study of Ti-bearing minerals and guidance for separation and recovery of niobium from kaolin clay.

Nov 30, 2020

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By J. G. Clevenger

Introduction Computer-based haul truck dispatching has been operational at Tyrone since May, 1980. The system, known as Dispatch, has accomplished significant productivity gains compared with the former method of manual radio dispatching. These gains translate into a reduction in equipment requirements or an increase in production. An operational mine may choose to increase production or reduce the number of equipment shifts operated, resulting in substantial operating savings. Dispatch Description The core of Dispatch is a VAX 11/780 computer. Originally purchased with 512 kbytes of memory, the system is now upgraded to 3.75 Mbytes to accommodate users from all areas of the operation. Dispatch alone requires 200 kbytes of locked-in memory, with an additional 300 kbytes of memory available on a top priority basis. The computer, located in the Tyrone Branch general office building, is connected by under-ground cables to the dispatch tower, 3.2 km (2 miles) from the general office. Four two-paired lines are used to drive two cathode ray tubes, a printer, and the Dispatch master panel. One CRT continuously displays pertinent pit information for the dispatcher's use. Routinely displayed transactions include truck assignments, changes in shovel material type, truck and shovel breakdowns and delays, and changes in truck, shovel, or dump status. Er¬ror detection capabilities include late arrival and improper input from the field panels. The second display terminal is used for utility reporting and input functions. Status reports are displayed for availability, position, and material type being handled by any given truck or shovel. Fuel reports are available indicating the time last fueled, quantity of fuel delivered, and the time spent fueling. A truck factor utility reports relative performance to other trucks and a shovel utility reports efficiencies in tons per shovel shift. Instantaneous shift reports and mine status reports are available. Inputs such as lineups, operator changes, new travel times, shovel bias, tie down times, and lunch times are all handled with the utility display terminal. The printer records a hard copy of operating truck locations and production from the beginning of each shift. If there is a system malfunction, the printer copy is readily available to the foreman for radio dispatching. The Dispatch master panel is a microprocessor-based panel that allows the dispatcher to override any computer-assigned transaction. Classification of "bad order" conditions and acceptance of certain field messages is entered through the master panel. This panel communicates with all truck and shovel field panels via UH radio frequency through a repeater tower located on a high ridge contiguous to the mining area. Each truck and shovel field panel unit transmits a coded signal that is identified by the computer. A typical communication sequence between field panels and the computer for one complete truck cycle is: • The truck panel LED display indicates the shovel number to which it is assigned. The truck arrives at its assigned shovel and the operator presses the "Arrive" button on the truck panel. As the computer receives the "Arrive" message, it concludes the return (empty) travel time and begins accumulating idle time before loading. • When the first dipper of muck is placed into the bed of the truck, the operator presses the "Load" button. The computer concludes the truck idle time accumulation and begins the loading time calculation. • When the truck is loaded, the shovel operator presses the "OK"

Jan 9, 1983

By Georges Cote, Ehsan Alavi, Eren Kusdogan

The City of Toronto's Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors (NTC) ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. 120 m of Starter tunnel and 70 m of Tail tunnel were excavated with roadheaders to help with the launch of the TBM and as part of the contract base scope work. JayDee Canada in Collaboration with Everest Equipment Co. developed an innovative approach to design and build a stand-alone Ring Machine Erector nicknamed Enterprise to erect precast segmental lining in Starter and Tail tunnels in lieu of Cast-In- Place concrete. This paper describes the design and provides feedback on the innovative procedure used to install the rings.

Jun 23, 2024

By Luis Yacher

CONTAC Engineers is a Chilean based company which works on process control and automation, principally for the minning industry. Jointly with other local and international engineering firms, CONTAC has participated in most of the last expansion and modernization plans being carried out at the Chilean pinning industry. At presente, CONTAC is involved on a research and development plan for the design and implementation of new instrument and process control procedures for mineral process automation. One of these efforts is the design of an ore size analyzer for coarse ore being transported over a conveyor belt. A feasibility and prototype study was made at a SAG Mill Plant and currently a high resolution, high speed analyzer is being developed. It will became available on early 1986.

Jan 1, 1986

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By Hojong Kim, Isehaq Al-Nafai, Kwadwo Osseo-Asare

The standard Gibbs free energy of formation (ΔGo f, 298) of bastnasite, (Ce, La, Nd, Pr)FCO3, was estimated using four different methods. The obtained average values were − 1589.5 kJ/mol for CeFCO3, − 1599.5 kJ/mol for LaFCO3, − 1589.1 kJ/mol for NdFCO3, and − 1595.4 kJ/mol for PrFCO3. The value for cerium bastnasite, CeFCO3, was used to construct a potential vs. pH (Eh-pH) diagram to investigate the stability relations of cerium bastnasite. The diagram shows that CeFCO3 is stable in neutral to basic conditions (pH ~ 6.5–11).

By M. Stefanakis, M. Errington, A. Kontopoulos, J. M. Prevosteau, K. Adam

The Olympias arsenical pyrite concentrate assaying 25 g/t Au, 40% S, 40% Fe and 12% As is highly refractory in nature; an oxidation pretreatment step is required to liberate gold and render it amenable to cyanidation. In the present study mineralogical analysis techniques including Image Analysis, SEM, EPMA, SIMS, Mossbauer, ICP/MS, etc., have been employed in order to investigate the mode of gold occurrence within the Olympias pyrites. Bacterial oxidation was used as a case pretreatment route and bacterially leached products were examined under SEM. The mineralogical observations and the relevant metallurgical and cyanidation test data were combined to establish a correlation between the mineralogical characteristics of the raw and oxidised products and conditions prevailing over the oxidative pretreatment step and the gold liberation achieved.

Jan 1, 1990

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau's coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964

By F. G. Miller

It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur, make up almost all of the total sulfur and occur in varying amounts in different coals and can vary greatly in coal of the same seam Pyritic sulfurs of 20% to 80% of the total sulfur have been reported Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and Jones (1) state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal, to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing a process, which can effectively produce in the fine fractions the efficiency of heavy media devices in the coarse.

Jan 1, 1963

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By Michel Grenier, Mahendra Gangal

Two methods used to measure the exposure of mine workers to diesel exhaust particulate were compared. One method was developed by the U.S. Bureau of Mines and the University of Minnesota's Particle Technology Laboratory. The method which was originally developed for use in coal mines is a size selective sampling technique. The other method uses an “ashing" approach to assess the exposure to diesel particulate. This second method is based on the principles of sampling according to the ACGIH respirable dust sampling criteria and the use of a silver membrane filter as collection substrate. Because a silver membrane filter is used, both respirable combustible dust (diesel particulate) and respirable silica can be measured from one sample. The comparison study took place in a Canadian lead-zinc mine during tests which were primarily designed to evaluate the gaseous and particulate emissions characteristics of new diesel engine technology. The study has shown that under the test conditions encountered, some differences were observed between the results as obtained by the two methods. These differences seem to depend on the characteristics of the respirable dust found in the work- place, i.e., size and composition. The impact, on sampling and analysis of diesel particulate, of the proposed guideline (ACGIH) for a TLV® of 0.15 mq/m3 is discussed briefly.

Jan 1, 1997

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By Henry N. McCarl

From the earliest use of crushed and broken stone as landfill for eroded gullies in trails and roads, to the mixing of sand and gravel with cement to make concrete, men and women have found mineral aggregates to be useful materials in satisfying human wants. Crushed stone, sand and gravel, volcanic cinders, pumice, manufactured lightweight aggregates, slag, cinders, expanded perlite and vermiculite, and a great array of recycled materials such as grog (broken or crushed brick) and fly ash have served as mineral aggregates. These materials have provided bulk and strength in portland cement concrete, bituminous concrete, road base, fill, concrete block, and plaster and stucco finishes. Mineral aggregates provide many special characteristics such as compressive and tensile strength, surface textures, weight and density, thermal and acoustical insulation, abrasion resistance, and impermeability to various concrete products and mixes. While most materials used as mineral aggregates are consumed on the basis of their low unit values, the large volumes extracted in the United States each year make them one of the most valuable mineral resources in current production. In 1960, US production of construction aggregate was just over a billion tons per year (Meyer and Zelnick, 1991). Two decades of accelerated interstate highway, residential, and commercial construction brought the total annual production of mineral aggregates to roughly 1.4 Gtpy by 1970 and just over 1.6 Gtpy by the late 1970s. General economic and related construction slowdowns in the early 1980s saw annual US production of aggregates fall to below 1.1 Gt in 1982, and then rise to just over 1.7 Gtpy in 1990, a new peak in mineral aggregate production and use. Per capita annual consumption of mineral aggregates was approximately 5.68 t/capita in 1960, 6.89 t/capita in 1970, rose to a high of 7.25 t/capita in 1979, and has since settled to just under 7 tpy for every man, woman, and child counted in the United States Census of 1990. The value of these materials came to approximately $9 billion in 1990. During the period 1960-1990, roughly half of all mineral aggregates were used in the construction of residential, commercial, and industrial structures, and the remainder was consumed in highways, bridges, and other transportation facilities such as railway roadbeds, airports, and water-related projects (Meyer and Zelnick, 1991). During the period 1988-1992, public works (highways, waterway projects, road maintenance, etc.) represented closer to 60% of annual mineral aggregate demand with residential and non-residential construction approximately 40%. The growing market share of public works projects has been mostly due to the dramatic slowdown in residential, commercial, and industrial construction during the 1988-1992 period.

Jan 1, 1994

By Gunder Homstvedt

The paper presents a new method for boring of blind inclined shafts. The machine, called BorPak, developed by The Robbins Company, operates similar to a mini TBM. It is a remote operated, self propelled drilling machine mounted on a crawler for high mobility and launched out of a starting tube for quick collaring. A short history of the operation of the prototype in Scandinavia and Canada is included in the paper. The BorPak is capable of boring raises at angles from 30° to 900 from horizontal in sizes ranging from 1.2m-2m diameter without the use of drill pipe. The BorPak represents an innovative tool for improved performance, reduced costs and creating a safer working environment.

Jan 1, 1993

By John R. Hawley

Ontario, one of the richest mining districts in the world, is a natural storehouse for much of the earth's fresh water supply. Covering over 344,000 square miles, the surface of this Canadian Province is dotted with 250,000 fresh water lakes and is laced with uncounted thousands of fresh water rivers and streams. The southern portion of the Province, for the most part, is flat or lazily rolling farmland. This is where most of the people in Ontario live. Although it is not a major mining area, southern Ontario does possess important deposits of salt, oil, gas and gypsum. Most of these deposits are being actively worked. Toronto, the capital city of Ontario, lies deep in the southern region. Here the climate is mild and the winters are short. The total annual precipitation consists of 27 inches of rain and 65 inches of snow. Most of the major mining companies that do business in Canada have made Toronto their Canadian headquarters. There are two reasons for this. The first, of course, is money. Toronto is the gathering place of many well- known financial institutions. The second is access. Toronto lies within a few hundred miles of some of the most spectacular mining enterprises that exist in the world.

Jan 1, 1973

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017