Search Documents

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,' the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill's Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

By James E. Brewer

Procedure for approval by the U. S. Army Corps of Engineers of a new source of aggregate is in three phases. Phase 1 consists of an investigation of a quarry or proposed quarry by district geologist and laboratory geologist and/or petrographer. The quarry face or suitable outcrop is logged in detail or, if exposures are poor, cores may be taken to determine whether further investigations are warranted. Phase 2 consists of thorough laboratory testing. Cores and crushed material are subjected to a number of acceptance and quality tests for soundness, absorption, abrasion, reactivity, and other properties. Petrographic analysis is also made. Phase 3 is a physical and economic study of the site and involves determining quantity of stone avail- available, amount-and character of overburden, condition of haul roads and distance to rail shipping point, plant flow sheets and capacity, aggregate sizes produced, and approximate price of material at plant.

Jan 1, 1966

By John F. Clarkson

White Pine Copper Company built and operated, from August, 1962 through May, 1963, a pilot plant to recover copper using a cyanide percolation leach of the sand fraction (+400 mesh) of the mill tailings (1, 2, 3). The pilot plant runs were metallurgically successful and preliminary engineering studies for a full scale operation were completed under contract by an outside engineering firm. Unfortunately, the net return projected at that time did not justify the proposed capital' investment. In the summer of 1973 the project was revived. The rise in selling price of copper over the previous ten years, compared to the projected operating cost of the leach plant, increased the calculated net return on investment with the most recent figures showing a 30% DCF. Basically, the reason for this favorable shift in profitability was that the cost for many of the reagents did not go up as fast in the previous ten years as did the selling price of copper. Using the Chemical Marketing Reporter costs, NaCN sold for 18.3¢/lb in 1963 and 20.75¢/lb in August, 1973. During this same period H2S04 went from $23.50 per ton to $35.90 per ton. In comparison, producer's prices for electrolytic copper were 31¢/lb in 1963 and 619 in 1973. Thus the price of copper went up 97% while the two reagents only increased 13% and 53%, respectively. The capital investment also escalated but, again, not to the same extent as the selling price of copper. These price differences no longer are valid' but they did provide justification for reexamining the project.

Jan 1, 1975

By Nomuqhele N. Nkosi, Yasuo Yabe, Musa D. Manzi, Raymond J. Durrheim, Siyanda B. Mngadi

This study examined rock failure in brittle rocks hosting the deep gold-bearing ore bodies on scales between millimeters and kilometres. This research study is part of the International Continental scientific Drilling Program (ICDP) project, “Drilling into Seismogenic Zones of M2.0-M5.5 earthquakes in deep South African gold mines” (DSeis). The broader ICDP-DSeis project aims include the examination of the extent of damage, the stress state around the fringes of the earthquake, and the potential existence of living organisms associated with deep-level earthquakes. Nevertheless, this study focused on two seismogenic zones – the Cooke 4 mine and Moab Khotsong mine. At Cooke 4 mine, the study examined the evolution of mining-induced fractures (M1-4) occurring ahead of the stope face during the extraction of the remnant shaft pillar. These fractures were monitored and delineated by a dense array of acoustic emission sensors that allowed hypocentres to be located with decimeter accuracy. Using this acoustic emission data, the DSeis team drilled and recovered the fractures, rock breccia and gouge using a sophisticated triple-tube drilling rig.

Apr 26, 2022

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By Pierre Ollivier, Dominique Morin

A general study of gold refractory arsenopyrite pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 1 unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery, furthermore, the arsenite and ferrous produced in solution have to he oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimisation study calculation for scaling-up the design and power requirements of an industrial installation, For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution, In that conditions the power cost is quite marginal, actually it is significant for the treatment of pure pyrite.

Jan 1, 1990

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By Karin Bäppler

Hydropower produces almost two-thirds of the world’s renewable electricity generation and delivers a major contribution on the ambition of the Paris Agreement and Sustainable Development Goals (SDG) with a range of benefits to society and environment. These include clean and flexible generation and storage in addition to reduced dependence on fossil fuels and avoidance of pollutants. The Limberg III PSP is one of the European projects that addresses the implementation of the UN SDGs. The challenge of the project is the construction of a 770 m long pressure shaft to be excavated with a TBM at an inclination of 42°.

Jun 13, 2023

By James M. Prudden, E. P. Jucevic

The Divide mining district occupies the center of a Tertiary caldera hosting the famous Divide silver lode and the crosscutting Gold Mountain mines. The northwest-southeast trending silver lode hosted ore with typically a 100:1 silver:gold ratio, high molybdenum content and argillic alteration dated at 16.5 m.y. within the Fraction Tuff. The east-west trending Oddie Rhyolite flow dome at Gold Mountain experienced possibly several periods of resurgence with repetitive silicification, brecciation and attendant precious metal deposition forming stockwork type mineralization. Silver-gold ratios average 10:1 for the mineralization phase of this 16.4 m.y. intrusive event. Similar chalcedonic mineralization registering a 3:1 silver:gold ratio cements conformable breccias within the Oddie Rhyolite basal flows unconformably overlying the Siebert Tuff on the northern flanks of Gold Mountain. Gray and red chalcedonic breccia matrix in the King Tonopah member of the Fraction Tuff contains a 50:1 silver :gold ratio.

Jan 1, 1990

By E. Yigit

Hydrometallurgical production of zinc from concentrates is generally carried out by H2SO4 leaching. For the smooth operation of this process, some harmful components must be removed from the leach solution before the electrolysis stage; MgO is one of these compounds. Zinc concentrate samples from the Mount Isa mines were used in leaching tests. Leaching tests with an aqueous solution of H2SO4 and SO2 gas were carried out at various temperatures, pH levels and leaching durations. While duration and the pH value of the solution were effective parameters in H2SO4 leaching, temperature and pH were more effective in SO2 leaching for the removal of MgCO3 and CaCO3. Removal of MgCO3 and CaCO3 was generally achieved at low pH values. The results show that SO2 gas can be a good alternative to sulfuric acid in the leaching of MgCO3 and CaCO3

Jan 1, 2010

As noted by D.W. Fuerstenau in his Plenary Lecture at the Conference on Extractive Metallurgy of Gold and Base Metals, Kalgoorlie, Australia, "Com¬minution of solids is surely one of the oldest technologies that, even in this day and age of DNAs, chips and space exploration, continues to challenge our scientific acumen and engineering ingenuity." Thus, the fundamentals of comminution continue to receive a great deal of attention in the literature. This was particularly true in 1992 with the publication of the proceedings from the SME-sponsored symposium, Comminution Theory and Practice. Papers covering topics ranging from liberation to comminution fundamentals to novel size reduction techniques are included in this review. Liberation Liberation continued to be a prime area of research interest, not only in terms of liberation modeling, but also in understanding the basic mechanisms involved in mineral liberation. King (Comminution - Theory and Practice, pp. 3-15) described a method for determining the interphase area between mineral grains. He showed how the mea¬surement of interphase area before and after comminution could be used to determine the presence or absence of intergranular fracture. Lin, Miller and Cortes (Kona, Vol. 7) discussed the use of computed tomography (CT) as a nondestructive means of investigating three-dimensional particle composition. The use of this technique in constructing coal washability curves from CT data was presented.

Jan 1, 1993

By T. G. Carnahan

The U.S. Department of the Interior, Bureau of Mines, performed a laboratory-scale investigation of technique for recovering silver from pregnant solutions generated in the hydrometallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This provides a means for recovery and simplified reduction of accessory silver to metal from ions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to-92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By Silvano Perla

Peabody Western Coal Co. operates two mines in northern Arizona. The Black Mesa and Kayenta coal mines are unique for several reasons. They both have only two customers: Southern California Edison’s Mohave generating station near Laughlin, NV and the Navajo generating station near Page, AZ. Both mines are close together. Between the two, they ship nearly 11 Mt/a (12 million stpy) of coal. Material is shipped to the power stations in two ways. This first is a 440- km-long (273-mile-long) underground slurry pipeline, the longest in the world. The second is an 11 -km-long (17-mile- long) long conveyor to four storage silos. Product is then shipped by train from the storage silos to the plant sites. Another factor makes these mines unusual. They are both situated in the middle of the 68,795km2 (17 million- acre) Navajo Reservation, home to the Navajo Nation and Hopi Tribe members. Nearly 90% of the Black Mesa and Kayentamines’ 850 employees are tribe members. Peabody Western Coal is the United States’ largest private employer of Native Americans.

Jan 1, 1995

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By AJIT SWAIN, SUNATI MOHANTY

The ability to predict the dewatering performance of an industrial hydrocyclone from a laboratory-model hydrocyclone is of great importance. In this study, laboratory-scale hydrocyclone experiments were conducted using silica sand samples at 10 percent solid concentration for dewatering with Mozley hydrocyclones with diameters of 2 in. and 4 in. The objective is to predict the design parameters for an industrial dewatering cyclone to achieve higher solid concentration in the underflow. A model was developed based on the Nageswararao hydrocyclone model with the help of a commercial simulator for a hydrocyclone operating at 100 t/h and 20 percent solid concentration to achieve 80 percent solid recovery at 45 percent solid concentration in the underflow.

Mar 1, 2023

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974