Search Documents

By Barbery G., A. Maachar, M. Bourassa

Laboratory testing for flotation circuit design is carried out on a routine basis in a large number of lab- oratories throughout the world. Usually a sample of ore, assumed to be characteristic of the material to be processed in a future plant, having a mass of the order of a few kilograms, is ground in a batch ball or rod mill, in the presence of water and some re- agents (for pH control, etc. .. ); after dilution to the adequate solid concentration, the resulting slurry is transferred into a laboratory batch flotation machine, having a volume which can vary from 0.5 to 8 10 -3m3. Various types of machines are in common use, manufactured by the same companies that market industrial size flotation machines. The operation of flotation in the laboratory is carried out by an experienced technician, who uses parameters such as impeller rotation speed, air flowrate addition, froth height, froth removal rate, in conjonction with reagent addition sequence, to "test" the ore. After flotation, the froth products ("concentrates"), and the solids remaining in the cell are filtered, dried, and analyzed for the various elements of interest. For flotation circuit design, a kinetic test is usually carried out, in which the froth products obtained at various times are collected to assess the time response of the ore in the laboratory machine with the combination of reagents used. Although this description is rather sketchy, it enables to outline some of the major difficulties in using laboratory data for flotation circuit design: 1. ore sample representatively 2. feed preparation procedure (laboratory compared to industrial scale) 3. laboratory procedures (type of ma- chine, type of operation, experimental errors. . . ) 4. flotation machine scale-up 5. flotation kinetic scale-up 6. flotation circuit design using laboratory data These various points will be discussed in the present paper, in order to stress the problem areas as well as possible solutions. ORE SAMPLE REPRESENTATIVITY It has been stated many times that one of the major problem in designing a flotation circuit is the representatively of the sample to be taken. Sampling of an ore body during prospection and evaluation is a specialized field, which has been progress in with the introduction of geostatistics. The application

Jan 1, 1986

By Edward I. Erlich

1984 saw the 30th anniversary of a momentous event in Soviet geology-the discovery of kimberlites in Siberia, an event that vaulted the Soviet Union to second rank among the world's producers of both gem and industrial diamonds. There are many legends associated with this story, legends about those who predicted the discovery and those who achieved it in the field. The story told here unfolded during the field campaigns of the 1940s through 1960s, as witnessed by the authors and their companies of an earlier generation. This story illustrates science, chance, and human emotions at work, resulting in a blend of conviction, courage, bureaucratic sniping, and competition for glory. At the same time, it is an illustration of the workings of the Soviet exploration system. In a broader sense, it is the realization of the Russian image-boundless natural wealth, indomitable ingenuity, and the rigid political economic system that permeates the Russian landscape as well as the people. Most accounts of the Siberian diamond saga begin with statements such as, "This discovery confirmed the predictions of...", or "It was a result of predictions of one of the greatest Soviet geologists, Academician V.S. Sobelov...". These are only part of the truth. It had become apparent even in the 1930s that the Siberian Platform contained one of the Earth's greatest Basaltic provinces, described in a monograph by Sobolev...; and at the end of the thirties, G.G. Moor of the Institute of Arctic Geology found alnoites, similar in many ways to kimberlites. At the same time, the famous polar geologist, N.N. Urvantsev found other kimberlite like rocks in the southern Taymir Peninsula, adjacent to the Siberian Platform. In publications describing these rocks, Moor and Urvantsev mentioned for the first time the possibility of finding diamondiferous kimberlites similar to those in South Africa. Unfortunately, Urvantsev spent little time in the field between terms in concentration camps. Moor was considered by his superiors to be no more than a good descriptive petrographer; they suggested to him that his conclusions should be backed up by more highly regarded specialists. Thereupon, Moor asked Sobolev to coauthor a paper with him and this became the widely quoted prediction about diamonds in Siberia. Another early paper should also be mentioned, an unpublished paper found by M.I. Rabkin in the geological archives of the Norilsk Metallurgical Plant, written by Yu. M. Sheinmann when he worked in the concentration camp there in the late forties. This report placed the probable location of yet-to-be-discovered kimberlites within less than 100 km of their correct location.

Jan 1, 1990

By R. G. Reddy

Iron solubility's in spent pickling (HFHNO3 -H2O) solutions were determined as a function of HF and HNO3 acid concentrations. A chemical analysis of the industrial pickling solutions and sludges was performed. The stable phases observed in the sludges are FeF3.3H2O and (FeCr)F3.3H20. Pure Fe metal, AISI 316 stainless steel and AISI 416 stainless steel were used in this study. The results show, that the solubility of Fe increased as the concentrations of HF increased in the pickling solution at a fixed concentration of HNO3. A reasonable agreement between the experimental solubility data and the theoretical calculated data was obtained. X-ray diffraction analysis showed that the solid solubility product formed in the ternary solution containing pure Fe is mainly, at a high pH value, FeO(OH) compounds and, at a low pH value, Fe F3.3H2O compounds.

Jan 1, 1994

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By V. D. Hanson

When maintenance of a plant or operation is under discussion immediately three "M's", all in short supply, are brought to mind - money, men and markets. This paper will present what currently is being done at our plants and its effect on the 3 "M's". Examination of coal realization figures (F.O.B. Mine) from 1945 to the present reveals the fact that open and free competition can and will meet market conditions. The industry, without benefit of advantages afforded tax and transportation wise to oil and gas, remains the backbone of the energy market of United States. Figure No. 1 shows the realization figures from 1945 through 1962 compared to the hourly earnings. Note that through 1945 to 1948 F.O.B. prices increased $1.93 per ton while hourly earnings increased $.66 per hour. Since 1948 (with the ex¬ception of 1957) F.O.B. prices have declined $.45/ton, while hourly earnings have increased $1.23 per hour. Basically the maintenance men possibly represent the highest increment rate in the overall hourly earning.

Jan 1, 1963

By Donald P. Richards, William M. Greenslade, Daniel E. Albers

INTRODUCTION The application of oil field technology to large diameter hole drilling is beginning to offer a cost effective alternative to conventional shaft sinking methods. The drilling of ventilation and small production shafts are, of course, not new. The major constraint to the drilling of large diameter production shafts has been the inability to drill holes large enough and straight enough to install and operate relatively high volume hoisting equipment. This paper discusses recent advancements in drilling technology as applied specifically to large diameter holes for use in the mining industry. The paper emphasizes the geotechnical and hydrologic considerations in assessing site conditions and their application to drilled shaft technology. The authors worked together on a recent feasibility study for a 6 m (20 ft.) diameter 975 m (3,200 ft.) drilled shaft in New Mexico. Their individual experience in drilling and geotechnical investigations related to shaft sinking is world wide. DRILLING TECHNOLOGY Large diameter hole drilling has been a natural evolvement of oil well rotary drilling techniques. Most problems that were encountered in the rotary drilling of large diameter holes have been

Jan 1, 1981

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

The Mesquite mine is being operated by Gold Fields Operating Co.-Mesquite, a subsidiary of Gold Fields Mining Corp. The mine Is located in southeastern California about 56 km (35 miles) east of the farming community of Brawley, California. The mine has been in commercial production since early 1986 and Is a conventional open pit mine developed on 6.1 m (20 foot) benches. The gold is recovered by heap leach using permanent heaps built in multiple 6.1 m (20 foot) lifts. This year's gold production will be in the range of 5,600 kg (180,000 troy ounces). Current ore production is about 18,140 tonnes (20,000 tons) per day while the total tons mined Is averaging 65,000 tonnes (72,000 tons) per day. The climate at the mine is extremely arid with rainfall of 7.6 cm (3 inches) per year. From early May until late October daytime temperatures generally exceed 37.8 degrees Celsius (100 degrees Fahrenheit) and can be as high as 37.9 degrees Celsius (120 degrees Fahrenheit).

Jan 1, 1989

By W. G. Pariseau

A study of coal pillar strength was done at the Beehive Mine during a three year period, 1974?1977, in a cooperative effort involving the University of Utah, RE/SPEC, Inc., and the American Coal Company (Pariseau et al, 1977). The Beehive Mine is located in the Wasatch Plateau coal field in central Utah near Orangeville, Utah, where mines are developed from outcrops between steep canyon walls with topographic relief of a kilometer or so (3,600 ft). Coal is found in Cretaceous sediments that dip gently to the west. Detailed geology of the Wasatch Plateau is described by Doelling (1972). Mining was done in the Blind Canyon seam. An earlier Deseret Mine worked the Hiawatha seam that is lower in the stratigraphic column by about 36 m (120 ft). Mining progress and ownership changes occurred in time with mine mergers and name changes eventually to the collective Des-Bee-Dove label. At the Beehive Mine, depth varied with topography but was approximately 360 m (1200 ft) on average; seam thickness varied from 1.5 to 6 m (5 to 20 ft) and usually required two passes of the miner. The mine was eventually closed and finally reclaimed in 2003. Semborski and Oakley (2006) present a brief history of the mine and describe the reclamation work in some detail. Figure 1 shows the surface topography in the vicinity of the mine that is in the center of the figure.

Feb 23, 2014

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives (HydroStar® 4208, DXG®-F7, Cyquest® N-900) using a potentiostatic technique. The current-time data obtained at 0.16V vs. SHE was analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A m-2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current-time data from the electrolyte without organic additives indicate progressive nucleation with two-dimensional (2-D) growth under diffusion control. SEM images obtained confirmed progressive nucleation with 2-D growth. 20 mg/L Cl- and 2.5 mg/L organic additives did not change the nucleation and growth mechanism, however the additives increased the number and reduced the size of copper nuclei leading to more uniform coverage of the stainless steel substrate.INTRODUCTION Electrowinning of copper is an important process in the manufacture of high purity copper metal. It is approximated that 20% of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole, and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth, and nature of the initial deposit (Sun and O'Keefe, 1992). Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature, and copper concentration, small amounts of organic smoothing agents (traditionally guar products) are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper dendrites, which leads to improved deposit quality by producing bright, smooth, and dense cathodes."

Jan 1, 2015

By G. L. Myers

The Fortitude skarn near Battle Mountain, NV is currently one of the largest producing gold skarns in the world. It contains about 11 Mt (12 million st) of minable ore grading 5.14 g/t (0.149 oz per st) and is the distal portion of a continuous skarn system in the Copper Canyon area centered on the Eocene Copper Canyon granodiorite porphyry. Calcsilicate compositions, opaque mineralogy, and the high gold grades are atypical of other base metal skarns (iron, Fe; copper, Cu; lead-zinc, Pb-Zn; or tungsten, W). The Copper Canyon skarn is systematically zoned from a garnet (AD 70-100) dominant, pyroxene (HD 20-45) subordinate zone, with major Cu mineralization, adjacent to the intrusive (West ore body), to a pyroxene (HD20-100) dominant, garnet (AD90-100 cores. AD 30-60 rims)subordinate assemblage, with major Au, near the distal marble front (Fortitude ore body). An extensive biotite ± diopsidic pyroxene ± kspar alteration halo surrounds the pyroxene > garnet gold-bearing skarn and represents the early stages of metasomatic alteration. Retrograde alteration is limited in areal extent and intensity, and consists of actinolite, chlorite, quartz, and prehnite. Economic gold mineralization begins in the pyroxene > garnet zone and continues to the marble front, a distance of 1 to 1.5 km (0.6 to 0.9 miles), respectively, from the plutonic contact. The opaque mineralogy in this gold zone includes pyrrhotite, arsenopyrite, marcasite, minor chalcopyrite, galena, sphalerite, argentite, hessite, hedleyite, volnyskite, and native bismuth and gold. The pyrite-pyrrhotite geothermometer yields temperatures that range from 450° C to 300°C (842° F to 582° F) and the electrum-argentite-sphalerite geothermometer yields temperatures which range from 290°C (554° F) at the marble front to about 420°C (788° F) more proximal to the intrusive. Log fS2 calculations from the sulfide assemblages yield values near - 10 with log fO2 values of about -30, in a solution of near neutral pH (5-6). Calculations of metal solubility suggest that the metals were transported as chloride complexes in the proximal skarn but that bisulfide complexes were predominant within the distal gold skarn. Relatively low oxidation states buffered by the carbonaceous to argilliceous, calcareous protolith and subsequent ferrous iron-rich skarn assemblages appear to have increased the gold carrying capacity of this large hydrothermal system.

Jan 1, 1991

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

By Dale S. Preece

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is a research facility located in Southeastern New Mexico. The WIPP is being developed by the U. S. Department of Energy (DOE) to demonstrate the safe storage of defense-related radioactive wastes in bedded salt. Since the WIPP is a research facility. a number of large-scale in situ experiments have been planned and are currently under construction (Munson, 1983). These experiments were designed to study various aspects of nuclear waste storage in bedded salt such as mechanical responses and creep closures of drifts, thermal response due to heated canisters, and thermally-induced fluid migration. One purpose of the WIPP is to develop and demonstrate a general predictive structural analysis capability for a bedded salt repository. One set of experiments, called the Geomechanical Evaluation (Room G), is heavily instrumented to study the creep around several rooms with different configuration. A Layout of the Geomechanical Evaluation room is shown in Figure 1. One portion of it consists of wedge shaped pillar where two drifts intersect at an angle of 7.5 degrees. The pillar can be seen at the bottom of Figure 1. One purpose of the wedge pillar experiment is to study progressive pillar failure in the tip region. Another is to determine how nonuniform pillar thickness affects creep closure of the drifts. An important aspect of the experiments is the correlation between experimental data and corresponding pretest finite element analyses of the site. The finite element simulations serve two purposes. First, the computer simulations aid in understanding the experimental results by providing calculated stress. strain and displacement fields that cannot be measured directly. Second, comparison of calculated and measured drift closures serves as a method for validating or improving the finite element models and the constitutive models employed. The wedge pillar geometry required a 3-D finite element creep calculation. Results from these 3-D calculations will be presented in this paper. A 2-D plane strain double drift model which approximates the wedge pillar geometry at a slice perpendicular to the drift has also been performed and will be compared to the 3-D results in this paper. FINITE ELEMENT COMPUTER PROGRAMS Two finite element computer programs. JAC (Biffle, 1984) and JAC3D (Biffle. 1986), were used. JAC is a 2-D finite element program developed for quasi-static analysis of non-linear solids. It employs the conjugate gradient iterative technique to obtain a solution Spatial integration is performed using a single gauss point in each four node quadrilateral element. An hourglass viscosity technique is used to control the zero energy modes that occur with single point integration. The single point integration combined with the explicit nature of the program and exploitation of CRAY-1 computer architecture results in very efficient execution J4: results were compared to results obtained with eight other 2-D structural creep computer codes in the second WIPP benchmark exercise (Morgan, 1981) JAC3D was derived from JAC to treat 3-D finite element models and has many of the same characteristics including single point integration and hourglass viscosity. These characteristics have made 3-D creep analyses more reasonable by significantly reducing computation time The first exercise of the creep capability

Jan 1, 1986

By K. Marutiram, T. Umadevi, R. Sah, K. Abhishek

Low-grade iron ore received from the West Singhbhum area of Jharkhand state in India was used to develop a beneficiation flow sheet to remove alumina (Al2O3) and silica (SiO2 ) from the ore to get iron (Fe)-rich product for steel plants. Mineral characterization showed that the main mineral constituents present in the head sample are goethite, limonite, hematite, quartz, clay and gibbsite. The head sample contained about 49.2 percent Fe, 8.79 percent alumina and 12.01 percent silica. The received iron ore sample is amenable to upgradation through beneficiation to get pellet grade concentrate. The beneficiation process was established, involving crushing, screening, jigging, spiral separation, size reduction, desliming and magnetic separation. The process showed significant enrichment in Fe values to 63.5 percent Fe in concentrate, from 49.2 percent Fe. From the developed flow sheet, it is possible to obtain pellet grade fines with 63.5 percent Fe, 2.92 percent SiO2 and 2.61 percent Al2O3 with 50.6 percent weight recovery. The overall tailing loss is 49.4 percent with 34.3 percent Fe, 21.28 percent SiO2 and 14.64 percent Al2O3

By Osamu Nishikokura, Jumpei Yamashita, Darrell Liebno, Malcolm Sheehan

"The Eglinton-Scarborough Crosstown Project builds a 19km LRT corridor that includes a 10km underground portion, between Keele Street and Laird Drive. The West Tunnel Contract (ECLC1-15) includes 6.5km of twin EPB TBM bored tunnels with a 5.75m internal diameter precast concrete segment lining (PCTL), between Keele Street and Yonge Street. This paper summarizes the overall scope of work, the technical challenges faced and innovative solutions developed by the contractor during the TBM move across an existing subway tunnel using state of the art high capacity strandjack gantry crane.1. PROJECT OVERVIEW The Greater Toronto and Hamilton Area (GTHA) is Canada’s largest urban region, populated with over 6 million people, and is one of the most rapidly growing regions in North America. One forecast estimates that the population of this region will increase to 8.6 million by the year 2031. In September 2008, Metrolinx, an agency of the Government of Ontario, launched a 25-year regional transportation plan named “The Big Move” to cope with the expected increase in transportation demand. The Eglinton-Scarborough Crosstown, one of the projects included in “The Big Move”, is a light rail transit (LRT) that will run across Toronto in an east-west direction between Mount Dennis and Kennedy along Eglinton Avenue. In October 2012, the West Tunnel Contract of the Crosstown LRT (ECLC1-15) was awarded to Crosstown Transit Constructors (CTC), a joint venture between Obayashi Canada Ltd., Kenny Construction Company, Kenaidan Contracting Ltd. and Technicore Underground Inc. The project includes approximately 6.2 km long twin bored tunnels, 9 cross passages, 1 emergency exit building, 7 sets of station headwalls, and an intermediate pair of extraction and launch shafts. Each of 6.5 km long twin tunnels are divided by the existing subway station into two drives: the first half from the launch shaft LS-1 (west of Keele Station) to the extraction shaft ES-1 (west of Eglinton West Station), and the second half from the launch shaft LS-2 (east of Eglinton West Station) to Yonge Station, as shown in Figure-1. The TBMs are extracted at ES-1 and moved to LS-2 over the existing Yonge-University Subway Line at Eglinton West Station before resumption of tunneling at LS-2."

Jan 1, 2016

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

The Janet Annenberg Hooker Hall of Geology, Gems and Minerals, located in the National Museum of Natural History, Smithsonian Institution, in Washington DC, opened in September, nine years after initial fundraising efforts were begun. The 1,858-m2 (20,000-sq ft), $16-million hall was mostly funded by private groups and individuals, including $1.7 million from 43 National Mining Associa¬tion (NMA) member companies. Companies that contributed more than $100,000 included Cyprus Amax, Phelps Dodge, Asarco, Homestake Mining, BHP, Caterpillar, Cleveland Cliffs, Exxon Coal and Minerals, Freeport-McMoRan, Newmont Mining and Peabody Holdings. The mining industry's contributions funded a walk-through Mine Gallery. It. features diora¬mas of four mines, as well as numerous specimens associated with the mines. The Mine Gal¬lery demonstrates to the public the importance of mining. The hall was named in honor of Hooker. She contributed $5 million in cash plus the Hooker Yellow Starburst Diamonds to the project. The hall is touted by the Smithsonian as the "most comprehensive earth science complex of its kind." It consists of seven galleries, each devoted to different aspects of gems, minerals and rocks. In addition to the Mine Gal¬lery, the hall contains a collection of gemstones and jewelry pieces, an extensive collection of minerals, a gallery devoted to plate tectonics and a gallery devoted to the moon, meteorites and the solar system. The new hall is a complete makeover of the old and outdated Geology Hall. It was built in the 1960s and finally closed to the public in 1995.

Jan 1, 1997

By C. M. Jones

Cyprus Sierrita Corp. has developed a training program that has led to several significant improvements in safety performance and productivity. Truck productivity has increased 6% as measured by truck cycle times. Increased skill levels and awareness on the part of the mine's operators are due to the new training effort. Costs associated with productivity training have been about $185,300. This includes program development and execution costs, as well as lost productivity during the training itself. These costs are offset by $1.9 million in savings attributable to the increased skill levels of technicians due to the training effort. Cyprus Sierrita is a subsidiary of Cyprus Amax of Englewood, CO. The company operates a copper and molybdenum mining and processing facility south of Tucson, AZ, near the town of Green Valley. The Cyprus Sierrita operation produces about 109 kt/a (240 million lbs/ year) of copper, 11.3 kt/a (25 million lbs/year) of molybdenum, 31.1 t/a (1 million oz/year) of silver and 1.8 t/a (4,000 lbs/year) of rhenium. The opera¬tion employs 770 people at the site. About 200 of these employees work in the mine operations. Mining at Sierrita uses standard open-pit techniques. Crews of 43 people rotate on 12-hour shifts. Hourly technicians are nonunion and do not use rigid job classifications to define pay. Rather, the system is designed to pay employees for what they are able to do. Administering this effort requires that training opportunities are provided to those people who desire them. Successful training opportunities al¬low people to gain skills. The more skills an employee can demonstrate, the higher his or her "tech level." A technician's pay is commensurate with his or her tech level. Much of Sierrita's training in past years concentrated on building basic

Jan 1, 1998

By Nora M. Hutt, Kevin A. Morin

Geochemical static tests are a basic component of geochemical assessments and predictions for acidic drainage, and include acid-base accounting and total-metal contents. A key database for such information is the International Static Database (ISD), which currently contains more than 45,000 static-test analyses from over 200 minesites. Such large databases are useful in identifying general trends and, just as important, the percentage of exceptions. General trends and significant exceptions can be seen in the ISD by comparing one parameter against another. This paper shows that bulk neutralization potential (bulk NP) obtained from acid titration is often a good indicator of neutralizing capacity above values of 10 t CaCO3/1000 t. Other types of calculated neutralizing capacity are then compared to bulk NP to determine if they, in fact, reliably represent actual neutralizing capacity and if they can substitute for the more time-consuming and expensive bulk NP. For example, bulk NP correlates better with Carbonate NP (from carbonate analyses) and Total-carbon NP (from total-carbon analyses) than with (Ca+Mg) CaNP (from solid-phase analyses of calcium and magnesium). This means that, in general, (Ca+Mg) CaNP is a less accurate substitute for bulk NP than the other types, and thus requires intensive site-specific justification if a substitution is attempted. This also means that measurement of the frequently less-expensive parameters of total carbon and carbonate can often substitute, within site-specific error bars, for the bulk-NP titration. However, the ISD also shows that non-carbonate minerals make the primary contribution to neutralization in up to 20% of samples, so Carbonate CaNP and Total-carbon CaNP do not always reveal the full neutralizing capacity of a sample.

Jan 1, 2000

By Luis Fernandez-Deza, James Hawn, Dustin Mount, Jean-Marc Wehrli

The RiverRenew Tunnel System project in Alexandria, VA forms part of a CSO scheme aimed at reducing overflows of combined stormwater and sewage into the Potomac River during storm events. A major piece of the project is a 12-foot internal diameter tunnel of approximately 12,000 feet length lined with a single-pass precast concrete segmental liner and excavated by an Earth-Pressure Balanced Shield TBM. The tunnel lies between 120 to 140 feet below grade in the clays of the Upper Potomac Formation with occasional dips of more granular, saturated soils of the Terrace Formation and the Alluvium. The TBM is launched from a figure-8 configuration Pumping/Screening Shaft located within AlexRenew’s operational Water Resource Recovery Facility. This paper discusses the challenges encountered during the launch of the TBM in short mode within a highly congested site and from narrow deep shafts.

Jun 13, 2023