Search Documents

By Cleophus Short

[Of the many occupations in and about the coal mines, those of the haulage crews are among the most hazardous. Statistics ship that the second greatest number of fatalities about the coal mines occur during haulage ion and through the use or misuse of haulage equipment. During the five year period between January 1, 1957 and January 1, 1962, the m stone mine had a. Sack haulage frequency of 4098 and mined 3, 541,939 toads per haulage fatality. Coal mire haulage is similar in respects to railroading. We gee very serious consideration to the instillation of tack and to the selection of the haulage crews. In doing this, we are attempting to have our coal mine haulage as. Safe as that of the railroads.]

Jan 1, 1963

The Gosowong epithermal quartz-adularia vein, in the Halmahera magmatic arc, is a new discovery in an area of primary tropical rain forest with no history of gold mining or mineralization. The newly recognized mineral district also contains a number of other epithermal vein systems, two centres of porphyry Cu-Au mineralization, and a number of argillic and advanced argillic alteration zones that may be related to underlying mineralization. Gosowong was discovered and tested through the application of basic exploration techniques including drainage sampling, soil sampling, trenching, magnetics, IP, and diamond drilling. Lapse time from the initial reconnaissance discovery of a stream sediment anomaly to the release of inferred resource estimates of approximately 1.0m ounces was just over 3 years.

Jan 1, 1997

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

Lingering effects of the 1990 oil shock that included overbuilding and corporate and individual financial distress caused the Gross Domestic Product to fall slightly to $5.67 billion (US billion = l09). With 254 million people - 697,000 in mining and petroleum - the US has more than 100 million dwelling units and 190 million licensed motor vehicles. New private housing starts fell 15% to one million units. New car production fell 11 % to 5.4 million units. Truck and bus production fell 8% to 3.4 million units. The inflation rate was 3%, while the prime rate of interest was 8.5%. The Producer Price Index (1982 = 100) changed as follows: -fuels and related products and power down 1% to 8l, • metals and metal products down 2% to 120, • chemicals and allied products up 2% to 126, and • non-metallic mineral products up to 2% to 117. Energy Imports of crude and refined petroleum, costing $50 billion, fell 5% to 2.8 billion bbl. Domestic petroleum production rose 1% to 3.6 billion bbl. Petroleum supplied about 39% of US energy, natural gas 24% and coal 22%. The National Energy Strategy was announced in February 1991. Its purpose is to encourage domestic production of fossil fuels and nuclear and renewable energy and to stimulate efficiencies in use. Congress continued to debate the strategy and took no action. Coal production fell 3% to 902 Mt (994 million st). About 60% of that came from surface operations. Seventy-eight percent of the total was used to generate electricity and 3% was coked.

Jan 1, 1992

By J. H. Lalor

The Olympic Dam deposit was discovered in July 1975 with the intersection of 38 m (125 ft) of 1.05% copper in diamond drill hole RD 1. A further eight holes were drilled with only marginal encouragement to November 1976 when RD 10 cored 170 m (558 ft) at 2.12% copper and an economic discovery was confirmed. The discovery of Olympic Dam is an excellent example of the application of broad-scale scientifically based conceptual studies to area selection combined with the backing of an exploration management willing to support its exploration scientists in testing their ideas with stratigraphic drilling. It also illustrates the persistence required in mineral exploration. The project began in 1969-1972 with the development of a conceptual model for the formation of sediment-hosted copper deposits. This model suggested that the alteration of continental-type basaltic rocks could release copper into solution from which it could be concentrated in favorable stratigraphic positions. In mid-1972, this concept was applied to a review of the Proterozoic and Lower Paleozoic rocks in South Australia aimed at defining targets for stratigraphic copper deposits.

Jan 1, 1991

By C. I. Basilio

The adsorption of dialkyl di-and mono-thio-phosphinates on gold, silver and gold-silver alloys has been studied in the present work. These reagents, which are selective collectors for sulfide flotation, have been found to improve precious metals recovery from ores. Voltammetric studies have indicated that dithiophosphinate adsorbs on gold at much higher potentials than on silver, while monothiophosphinate adsorbs only on silver. However, both adsorb on gold-silver alloys with the adsorption potential decreasing with increasing silver content. Using FTIR spectroscopic measurements, the surface species formed during the interactions of these collectors have been identified. The results of the electrochemical and spectroscopic measurements have been compared with the contact angle data obtained at controlled potential conditions.

Jan 1, 1992

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By David R. Crouthamel, Francis L. Fong, Troy L. Page

This paper focuses on the results and the performance of the grouting program as a means to control groundwater infiltration during the excavation of the 7.7 km (25,160 lf.), 3.5m (11 ft. - 7 in.) diameter Inter-Island Tunnel beneath Boston Harbor in Massachusetts. Two major operations of grouting were performed - water cutoff grouting behind the tunnel heading after excavation and face grouting ahead of the Tunnel Boring Machine (TBM) operation. An array of products from cementitious to chemical grouts and various grouting procedures and equipment were employed to evaluate their effectiveness in controlling the water in-flows. Evaluation of the overall performance of each of the grouting rations, overall costs and comparison of face grouting versus post excavation grouting is made.

Jan 1, 1997

By Harrie van Dijk

Feeding laterite nickel slurry into high pressure acid­leach (HPAL) autoclaves in an aggressive environment with slurries heated up to 200°C requires a special pump design. For decades the GEHO piston diaphragm pumps have been used for autoclave feeding at gold ore pressure oxidation plants with slurries up to l 77°C. Lessons learned from these installations have been instrumental in designing second generation feed pumps for processing laterite nickel with operating temperatures of 200°C and a flow rate of 400 m3/h. The Australian nickel industry is using momentarily 8 GEHO positive displacement piston diaphragm pumps. For this application six GEHO ZPM 900 "dropleg" pumps have been supplied to the Murrin Murrin project and two to Bulong.

Jan 1, 2000

By Karel Rössler, Petr Vítek

"The Ejpovice tunnels in Czech Republic were built by EPBM in soft Clyashale, and in weathered profile with low soil overburden. The segmented liner at the cross-passage openings required support, which would not interfere with the EPBM clearance envelope during the scheduled pull back of the EPBM through both tunnel tubes. For that reason support frames or radial bolting could not be used. Steel rods inserted into the neighboring segments during the ring assembly, and later grouted were tested and realized as an innovative solution. The paper presents practical experience gained with the segmented liner support during cross-passages construction. INTRODUCTION An innovative solution using the grouted dowels was developed and realized for sixteen cross-passage openings of the twin Ejpovice Tunnels, whose construction was part of the railway track Rokycany – Plzen modernization. The following paper described practical experience gained with the innovative support of cross-passage openings, which was realized by short steel dowels grouted within the segments of the EPBM segmented liner. The paper is a continuation of the paper published in WTC 2015, which described the design aspects of the grouted dowels support, while the following paper concentrated on the production, and the performance of the dowel support observed during the breakout for the cross-passages openings. The connection by grouted dowels was patented by Metrostav, a.s. Company THE EJPOVICE TUNNELS CONSTRUCTION The Ejpovice tunnels construction started in 2013. The start of the high speed train operation through the tunnels was planned for 2018. The project was funded by the state government with the support of European Union funds of up to 70%.The tunnels were excavated with one EPBM (Earth Pressure Balanced Machine) with the external diameter of 9.89 m. The segmental liner inner diameter was 8.7 m, and thickness of 0.4 m. First, the South tunnel tube was excavated from the East portal, then the EPBM was pulled back through the South tunnel, and the excavation was started from the same portal for the North tube. After the South tube was freed from the EPBM excavation operations the cross-passage construction started. Due to the short time schedule, in the North tube the cross-passage construction started while the tunnel was still under construction. Therefore, the cross-passage construction was performed concurrently with the segments transportation, and with the EPBM pull-back through the tunnel. There were 8 cross-passages along the tunnels with a maximum distance of about 500 m, Fig.1."

Jan 1, 2016

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By Muhammad Kamran, NIAZ MUHAMMAD SHAHANI

This study elucidates a new idea to predict mine fire levels by employing several machine learning techniques. A total of 120 patterns of various mine fire influencing parameters, such as oxygen, nitrogen, carbon monoxide, and temperature, were compiled from the Adularya coal mine in Turkey. Techniques like t-distributed stochastic neighbor embedding (t-SNE) and k-means clustering were used to process the data, and support vector classification (SVC) was executed to predict various levels of the mine fire. The results revealed that the proposed model has higher credibility to predict the various levels of underground mine fires.

Feb 14, 2022

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1.0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of S02 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By Terry S. Maley

With some exceptions, minerals may be acquired on the unappropriated public lands by one of three methods: (1) mining claim location under the General Mining Law of 1872; (2) mineral lease under the Mineral Leasing Act of 1920; and (3) sale contract under the Mineral Materials Act of 1947. Leasable minerals such as oil, gas, coal and phosphate are specifically designated as leasable in the Mineral Leasing Act so the method of acquisition is clear. As a general rule, metallic minerals are acquired by mining claim location. However the nonmetallic minerals, most of which are industrial minerals or gemstones, present a more difficult problem. These minerals are acquired either by mining claim or a sale contract depending on their chemical composition, physical properties and the use to which they are put. The Act of July 23, 1955 (30 U.S.C. 61 1) provided that uncommon varieties of sand, stone, gravel, pumice, pumicite or cinders are locatable; whereas, common varieties of such minerals may only be acquired by a contract of sale. The widespread location of mining claims to appropriate such deposits has caused many land management problems. Federal court and Interior decisions offer the most useful guidelines in determining the most appropriate method of acquisition.

Jan 1, 1991