Search Documents

By John Matthews

During 1982 and 1983, it became increasingly clear that North River No. 1 Mine would have to buy a set of replacement longwall shields. Despite extensive efforts to make improvements, the shields that were in place at that time were incapable of holding the roof. North River Energy had limited experience in specifying and acquiring longwall roof supports, but a great deal of experience with our conditions and needs. We there- fore compiled a shield evaluation method that uniquely responded to our situation. The resulting system emphasized teamwork among operating, maintenance and engineering personnel. The charge from management was threefold: select shields to support maximum expected loads, optimize face operations, and pay attention to detail. Final selection was made objectively, based on all available information. We chose a 5516 KN (620 tons) support with a minimum yield load density of 760 KN/m2 (7.9 tons/ft2). This paper reviews our process of specification, design, prototype testing, and fabrication, and offers some relevant suggestions.

Jan 1, 1986

By Jacob L. Mathis, Todd Tharpe, Jonathan Steflik, R. M. True

In June 2022, Louisville MSD completed a 6.5 km (4-mile), 6.1 m (20-foot) finisheddiameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. During construction, the Ohio River Tunnel alignment was expanded 2.4 km (1.5 miles) into areas where natural gas was detected. Without delaying construction, the project team developed and implemented a natural gas risk mitigation strategy to safely excavate the tunnel via TBM and install concrete lining. The risk mitigation strategy included the installation of gas-vent borings, increased tunnel ventilation, retrofitting tunneling equipment for “gassy” operations, and modifying the project specific HASP.

Jun 13, 2023

By E. Arioglu

Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence (?Smax) induced by chain pillar convergence has been related to a parameter (h/I -p) by linear regression. (Notations are expressed in this discussion's Fig. I (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goaf may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between ?Smax/m vs. h/1-p. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data.

Jan 1, 1992

By R. N. Gow

EH-pH diagrams are useful tools in understanding how mineral surfaces react in solution and particularly how aqueous conditions can be changed to enhance mineral leaching processes. However, successful application of these diagrams requires several things be kept in mind to prevent what others have termed ?gross errors? in their calculation and use. The aqueous Cu-S system is used as the basis for explaining the mass-balanced method of calculating EH-pH diagrams with the thermodynamic equilibrium software, STABCAL. This includes a breakdown of the Gibbs? Phase Rule and how it is employed in STABCAL to modify the diagrams. This methodology was then applied to the aqueous Cu-As-S system and resulting diagrams are compared against examples of those generated using the predominant-ion method. The resulting mass-balanced diagram for enargite (Cu3AsS4) is noted to compare well with spectroelectrochemical measurements using Raman spectroscopy and cyclic voltammetry.

Feb 23, 2014

By Rodger C. Smith

The topic chat has been assigned to me ?Economic and Political Climate of the Potash Industry? is a function of two basic facts: 1. Potassium is absolutely essential to plant and animal growth. Along with nitrogen and phosphorus it is one of three major plant nutrients, the three nutrients required in largest quantities for plant growth. 2. United States is unequivocally an "have not" nation with regard to potassium. Quantity of potassium ores is limited and, more disturbing, the cost of production at all U.S. potash mines is marginal in comparison with the major producing countries, i.e. Canada and U.S.S.R.

Jan 1, 1983

By K. A. Natarajan, K. Karthiga Devi

"A biodegradable flocculant was produced during growth of Bacillus megaterium. The major component of the bioflocculant was found to be a polysaccharide composed of some proteins. Fourier transform infrared (FTIR) spectra analysis revealed the presence of carboxyl and hydroxyl groups in the bioflocculant, and thermal characterization by differential scanning calorimetry (DSC) showed the transition and crystalline melting point at 90-105°C. The effects of bioflocculant dosage and pH on the flocculation of mineral suspensions were evaluated. The bioflocculant exhibited good flocculating capability on mineral suspensions and achieved flocculating efficiencies of 90 percent for kaolinite and 85 percent for hematite suspensions at a dosage of only 5 mL/L. The maximum arsenite removal was found to be 90 percent at a bioflocculant dosage of 2 g/L, which is better than traditional chemical flocculants. This study demonstrates that microbial bioflocculants have potential for application in environmental cleanup, such as in the flocculation of mineral fines and in the remediation of solutions that contain toxic heavy metals.IntroductionBioflocculants are biopolymers produced by microorganisms during their growths. The predominant components of a bioflocculant are extracellular polymeric substances such as glycoprotein, protein, cellulose and nucleic acid (Salehizadeh and Shojaosadati, 2001). Bioflocculants have gained much wider attention due to their biodegradability and safety. In recent years, the study of bioflocculants has attracted wide attention. Bioflocculants can be nontoxic, harmless and eco-friendly. Normally, they exhibit different functional properties, serving as stabilizer, dispersant or thickener. Among these properties, flocculation is of major interest. For example, Phormidium sp. strain J-1, isolated from a drainage channel, exhibited excellent flocculation activity for bentonite particles in liquid suspension (Fattom and Shilo, 1984). A protein bioflocculant produced by Rhodococcus erythropolis could efficiently flocculate suspended solids while losing their flocculating activity by enzymatic digestion (Kurane et al., 1994, Takeda et al., 1991). Klebsiella sp. strain S11 screened from activated sludge was unable to flocculate without the addition of calcium chloride (Dermlim et al., 1999)."

Jan 1, 2015

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using either a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion, and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent.

Jan 1, 1990

In 1993, the United States' economy grew at a rate of about 3%. The Gross Domestic Product rose to $6.4 trillion. With more than 258 million people - 599,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose 7% to 1.3 million units, new car production fell 3% to 5.5 million units and truck and bus production rose 21 % to 4.9 million units. The rate of inflation was under 3% and the prime rate of interest 6%. The Producer Price Index (1982 = 100) was unchanged from 1992 for fuels and re¬lated products and power at 80 and met¬als and metal products at 119, while chemicals and allied products rose 2% to 128 and non-metallic mineral prod¬ucts rose 2% to 120. The merchandise trade deficit rose 27% to $116 billion.

Jan 1, 1994

By Joel L. Morrison

The preparation of coal-water slurry fuel (CWSF) has the potential to be a commercially viable technology for the coal industry. The technology base required to prepare stable CWSF using grinding circuits has been developed over the past decade and is now being applied to the preparation of CWSF from wet coal fines which are generated during coal beneficiation. When preparing CWSF, the optimum CWSF formulation must be determined to ensure that the fuel will be stable while having acceptable atomization and combustion properties, and the production run must be monitored closely to ensure that the CWSF quality is maintained. This paper describes the CWSF formulation process, CWSF preparation circuits, and some of typical problems encountered in, and solutions to, the transportation and storage of CWSF.

Jan 1, 1993

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By Robert S. Hendricks

The paper describes the design and operation of a Shaft Boring Machine (SBM). The machine has been developed by The Robbins Company. It is anticipated that the prototype, which will bore shafts in the 6.1 to 7.3 m (20 to 24 ft) size range, will be placed in operation during 1985. This pioneering application of rapid excavation technology is expected to lead to significant improvements in the cost and speed of shaft construction. The technical and economic factors which have limited the employment of Shaft Drilling and which caused unsatisfactory results with earlier attempts at Shaft Boring are reviewed. The design criteria adapted to overcome these problems are discussed. Cost and performance estimates are presented and are compared to conventional sinking methods. Factors that influence the application of the SBM to specific projects are reviewed.

Jan 1, 1985

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By D. L. McCain

The movement of solids by pipeline is an art dating back well over 100 years as evidenced by many references in the literature. Even though all of the early pipeline transport systems were based on trial and error and relied mainly upon the designer's experience, hydraulic transport offered distinct advantages in convenience or cost for the chemical, mining, and civil engineering industries. It became well established for in-plant process lines, dredging, waste disposal, and other uses almost exclusively for short distances. During more recent times, much research work has been done in an attempt to understand the underlying principles involved in transporting solids in a fluid. Design criteria for pumping slurries have evolved to the point where pipelines designed for distances of several miles to several hundred miles can be accomplished successfully. Consolidation Coal Company designed and built a 10-inch diameter 108-mile long line1 for transporting coal in the 1950's and operated it from 1957 to 1963 when it was placed in mothballs because of falling freight rates for rail shipment. More recently, the 273-mile Black Mesa Pipeline2 was built and is operating. There are other examples of long distance pipelines,3 but all are for specially prepared fine slurries which allow the pipeline to be operated more economically.

Jan 1, 1975

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By H. Sevim

Belt network simulators developed in the last two decades are reviewed. Critical parameters in belt network design are identified, and the capabilities of belt simulators in providing values of these parameters are investigated. An alternative design model that optimizes values of the critical parameters is introduced. To illustrate the capabilities of the alternative model, a real life case is treated and the outcomes are discussed.

Jan 1, 1990

By Michael Roach

"There’s a bit of confusion and misinformation in the tunneling and underground construction industry regarding contractor joint ventures. If it was all so clear I would not have been "asked" to write this article. For those of us on the contractors’ side of the fence, joint venture business relationships have been a part of life for a long time. But even for contractors, there can be a bit of confusion, and it normally begins on bid day.How often have you received bid results and wondered (out loud, usually), "Who the hell are the Lake Mead Intake Constructors"? or the "Regional Connector Constructors"? Once you get past the name, you see that there is nothing behind Oz’s curtain other than a couple of contractors bidding and building work in an attempt to make a profit. So take a few minutes to read the rest of this, and I’ll do my best to dispel a few mythWhat is a joint venture?In some form or fashion, joint ventures are as old as industry itself. In the United States, some of the earliest (and largest) joint ventures involved the railroads and oil companies in the late 1800s. In the United States’ underground construction industry, joint venture names such as, Healy-Greenfield, Green and Winston, Gates & Fox and Walsh, Shea-Ball, Kenny-Paschen and S&M-Traylor bring back memories of successful joint ventures that operated over many projects.There are nearly as many definitions for joint ventures (JVs) as there are attorneys. A short and simple definition is, "an association of two or more companies engaged in a singular, for-profit business enterprise without actual partnership or incorporation." That’s it. Two or more contractors decide to partner up for one or more projects. One benefit of the JV relationship is that the partners typically do not need to file incorporation documents, or articles of organization within the state where they intend to operate. So it is a relatively easy business arrangement to pull together. Other benefits of the JV arrangement include: • Oportunities to gain new expertise and capacity.• The ability for firms to move into new geographic markets.• JV agreements are not long-term commitments.• Sharing of financial support for a project.• Sharing of financial risks within a project. between the partners.• Can complicate dispute resolutions with the owner and between partners"

Jan 1, 2014