Search Documents

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy's Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation's coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976

The introduction of nitro-carbo-nitrate (NCN) blasting agents has been one of the most significant innovations in the explosive industry in the last twenty years. The most commonly used blasting agent is a rather narrowly proportioned mixture by weight of 94% ammonium nitrate (AN) and 6% No. 2 diesel fuel oil (FO) that is generally designated as ANFO. Other formulations have been developed but none of these have been as extensively used as ANFO. The relative safety of the nitro-carbo-nitrate (NCN) blasting agents almost immediately suggested bulk loading techniques to obtain economies in materials handling. The first attempt at bulk handling was to pneumatically load boreholes with ANFO. When the initial experiments were made in 1957, it was apparent that there were three problem areas which needed study to minimize potential hazards. These were: 1. Static Electricity 2. Fumes 3. Safe Handling Procedures Since those early days, considerable work has been performed in evaluating these problem areas and in arriving at procedures and recommendations that would provide the required safety. Despite the relative insensitivity of ANFO type products, all normal practices for the safe handling of explosives should be obselved. Smoking should not be tolerated in the vicinity of blasting agents and misfires should be handled in the same manner as a misfire with a dynamite charge. The purpose of this Technical Report is to discuss the problems of static electricity and fumes and the solutions that have been developed. Safe handling procedures have been discussed by the Bureau of Mines and are specified by various state and local regulations. Since regulations vary from state to state, the local, applicable regulations must be followed within the area of their jurisdiction. General information is contained in a U. S. Bureau of Mines report, IC 8179, "Safety Recommendations for Sensitized Ammonium Nitrate Blasting Agents" (1963).

Jan 1, 1973

By W. A. Hustrulid

Introduction A problem that has faced mining engineers and mining geologists for many years is how to best explore a particular prospect so that the basic decision as to whether the material present is ore or only high-grade rock can be made with some confidence. It is obvious that one could not begin a large scale mining program on the basis of tests made on a few hand samples. On the other hand, one could not be 100 percent certain as to the average grade or tonnage before beginning development, as this would require the orebody to be mined out in the sampling process. The basic objectives of the exploration program can be stated as (1) to reduce mining risk; (2) to lessen the cost of development; and (3) to increase the profits of mining. The exploration program should be terminated when these objectives are no longer being met. The construction of tunnels is a specific mining operation. In the exploration program one should gather the data needed to determine (1) the type of excavation technique(s) to be used; and (2) the rate of advance that might be expected. As in the evaluation of an orebody, with the data collected it should be possible to estimate mining costs and project life. Unfortunately, at the present time, it is not possible to do this at least when dealing with medium to hard rock types. The reason for this, it is felt, is basically the inability to identify what specific rock mass properties are of use in tunnel design and to specify how these may be obtained in an exploration program. In short, the exploration program should be designed to give information regarding both the volume (length) and 'grade' (in

Jan 1, 1997

By J. Killian, S. Cox

Many questions exist within the geotechnical industry as to the applicability of Strength Reduction Factor (SRF) values to the design acceptance criteria (DAC) of mining operations. There are many factors that contribute to changes in the SRF estimate, some of which are numerical (e.g. dilation angle) and some of which are geometric (e.g. model grid size)[1]. Numerous studies have confirmed equivalent values of SRF and FOS are found for soil slopes of limited height as presented in, [2] and [3]. However, significant deviation of the SRF value was observed for highly cohesive materials (rock slopes) of heights typically encountered in mining, [4]. This paper builds on the work presented in [4], providing a more rigorous examination of the modeling parameters that control the SRF estimate. The failure mechanism assumed for this study was a simple circular shear surface in a uniform material. Both LEM and numerical methods are suited well for analysis of this failure mechanism. A parametric study was completed to evaluate and test the relationships of key numerical variables that affect the estimated value of the SRF using Itasca’s Fast Lagrangian Analysis of Continua (FLACTM) software. The effect of groundwater has been tested and may be significant but is not presented as part of this body of work for brevity and simplicity of presentation.

Mar 2, 2022

By Jaril B. Lavrencic

The unique and irregulator distribution of working places in a mine always poses the two questions: - which and how much production equipment is to be used, - what production can be expected. Since the development of analytical methods would be impractical for such cases, a lot of computer programs has emerged in recent years trying to simulate the productiom process and thus find the best answer. The usege of a simulator has its dark side well felt by the author(s) of such a program: the credibility and the confidence of the customer. Using the simulator means to respect and to incorporate all the restrictions imposed by the narow underground space, methods of production, safety regulations etc., which can turn out to become a major programming effort. If the program is not properly structured, it will be used for a single special' case only, and never again. In this paper the structure and internal mechanism of the simulator is described for which the author believes that can easily be adapted to conditions of various underground and open pit mines. MINSIM tries to reach the following rather ambitious goals: 1) Estimation of the production before opening the mine, or a part of the mine. 2) Training the personnel to make decisions. 3) Making the daily time schedules for the entire fleet of the equipment units.

Jan 1, 1989

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By Kenneth V. Luza

Underclays are associated with coals found in eastern Oklahoma. These coals are of bituminous rank and are in beds of Middle and Late Pennsylvanian age. They occur in an area of about 8,000 mi2, within the southern part of the Western Interior Coal Region. The rocks of the area consist of a thick series of sandstones, shales, underclays, coals, and limestones. There are more than 40 beds of bituminous coal in the state, but only 12 of these have been mined over large areas. The 12 are, from oldest to youngest: the lower Hartshorne, upper Hartshorne, McAlester (Stigler), upper McAlester, Cavanal, Rowe, Secor, Weir-Pittsburg, Mineral, Croweburg, Iron Post, and Dawson coals. None of the underclay associated with these coal beds is known to have been exploited commercially. Nine samples of underclay from beneath the Croweburg coal were collected over a wide area in the eastern Oklahoma coal field for evaluation. The underclays are usually shades of gray with brown or orange iron-oxide staining. Although soft and plastic in some places, they are generally hard and slickensided, and contain abundant carbonized plant fragments. Bulk chemical analyses, clay mineral identification, and ceramic tests were performed on each underclay sample. The dominant clay minerals are illite and kaolinite with some mixed-layer clays. Silica (Si02) ranges from 45.96% to 59.03% and alumina (Al2O3) varies from 14.98% to 23.60%. The U.S. Bureau of Mines Tuscaloosa Re- search Center conducted the ceramic evaluations. Samples were slow fired from 1,000°C to 1,250°C in 50°C intervals. Bulk density, color, percent linear shrinkage, and percent absorption were determined for each slow fire test. All Croweburg underclay samples are best suited for building brick.

Jan 1, 1999

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By S. R. S. Sastri, D. K. Senguta, S. K. Bhaumik, G. V. Rao

The amenability of a calcite-bearing ore to the reduction of silica to below 0.2% by physical beneficiation was studied. The objective was to use the ore as a raw material for seawater magnesia production. The ore contains complex gangue minerals such as diopside, forsterite, phlogopite, clinohumite, graphite and quartz. These contribute to around 25% acid insolubles with 6% SiO2. Reverse-flotation studies using various cationic collectors with tannin as a depressant indicated the possibility of reducing the acid insolubles to around 5%. Direct flotation of calcite with anionic sodium oleate in the presence of sodium silicate and lactic acid as a depressant indicated the possibility of reducing the acid insolubles to below 3% and the SiO2 to from 0.2% to 0.3%. Lactic acid was found to be an effective depressant of the complex gangue minerals in the ore.

Jan 1, 2000

By William C. Cooley

Modern tunnel boring machines are subject to excessive cutter wear and bearing failures when used in hard and abrasive rock. In very hard rock, the high cost of cutter and bearing replacement, combined with slower excavation progress, make it more economical to drive tunnels by conventional drill and blast methods. The use of high pressure water jets to break rock provides a promising alternative. Experimental data indicate that the specific energy (the energy expended per unit volume of rock broken) decreases as the water jet pressure increases. Continuous jets are generally limited to pressures below 100,000 psi, whereas pulsed jets from a water cannon can attain much higher pressures. Therefore, the Federal Railroad Administration of the U. S. Department of Transportation has sponsored the design (Ref. 1 & 2) and the fabrication and testing (Ref. 3 & 4) of a water cannon to determine its effectiveness in rock disintegration at very high pressures. This paper reports the results of laboratory tests with pulsed jets against large rock samples at pressures of 125,000 to 650,000 psi and field tests against dolomitic limestone and granitic gneiss at pressures near 450,000 psi. Although initial tests were made with a small nozzle, operating at off-design conditions (Ref. 4), this paper only covers results with the full-size nozzle, including 55 laboratory test shots and 67 field test shots.

Jan 1, 1974

By Steven Hart, Graeme Hill

Boddington Gold Mine is situated 130km South-east of Perth, WA. The operation is managed by Worsley Alumina Pty Ltd. The Direct Leach plant was commissioned in mid 1986 at a rate of 3 million tonnes per annum. The plant was upgraded to 4.5 mtpa in 1988 and almost immediately to 6mtpa in 1989. Subsequent debottlenecking resulted in further increases in throughput up to 7mtpa by 1991. The SupergenelBasement Plant was constructed in 1990 and commissioned in early 1991. It was designed to process both copper-gold-silver anomalies within the laterite gold orebody and future hard rock ores. The Supergene plant incorporated control potential s­ulphidisation (CPS) and flotation ahead of CIL to remove a host of copper minerals. It operated in that configuration for 2 years at rates up to 350,000 tpa and average grades of 6.0 git gold and 1.2% copper. Gold recovery averaged 90.7% and copper recovery averaged 80.0% before the flotation circuit was decommissioned in March 1993. Quartz hosted high grade, free milling oxide and basement ores were discovered at the northern end of the orebody in 1990 and now comprise the major feed source to the basement plant. Oxide ores are currently milled at a rate of 550,000 tpa, while basement ores are milled at a 420,000 tpa rate. Metallurgical testwork during the feasibility stages indicated that up to 30% of gold in plant feed could be recovered by gravity separation methods. It was also highlighted that signifi­cant improvements in overall plant recovery and reduced operating costs would be achieved by maximising gravity gold recovery ahead of cyanidation. To achieve this, rec;iesign and upgrade of the gravity circuit was necessary.

Jan 1, 1995

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By J. J. Scott, G. H. Bennett

INTRODUCTION Friction Rock Stabilizers, commonly called Split Sets,tm* have been under development since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977 and, to date, over five million units have been marketed to metal mines. The present rate of useage is near 3 1/2 million units per year which is approximately 50 per cent of all roof fixtures used in the United States metal mining industry. Mr. Richard Hoppe, Senior Editor of Engineering & Mining Journal, in an article of the February, 1979, issue, entitled "Winning the Battle Against Bad Ground", said, "In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J. Scott and developed by Ingersoll-Rand Co." This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of the Friction Stabilizer system. SPLIT SET STABILIZERS The Split Set System is a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: *Trade Mark of Ingersoll-Rand Co.

Jan 1, 1979

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

By Kenneth N. Han, Jianshe Liu

Various techniques used in the removal of metal ions from effluent streams have been reviewed. These techniques include recovery of metals by biological treatment, chelating agents, adsorption, ion- exchange and chemical precipitation. The main thrust of this paper however, is concerned with the removal of cadmium and zinc ions from the solution by adsorption utilizing liquid fluidized beds. The bed particles used were silica of 150x200 mesh. The range of the concentration of these ions studied was 10-3 to 10-5 M. Important variables examined included flow rate, concentration of metal ions and amount of bed particles. A mathematical model describing the concentration profile of metal ions in the axial direction in liquid fluidized beds has been developed. The equation of continuity was solved numerically and the results were used to predict the recovery of metal ions in fluidized beds.

Jan 1, 1992