Search Documents

By William C. Howe

This paper describes the technical status of the atmospheric pressure fluidized bed combustion (AFBC) process for utility steam generation. Major areas where AFBC development work is needed are discussed. Various approaches to solving these key issues are identified and the ongoing research and development programs addressing the key development areas are described. Other significant programs pertaining to the development of AFBC for utility steam generation are also discussed and needs for future work identified.

Jan 1, 1978

By David M. Sullivan

Jim Walter Resources, Inc., (JWR) a division of Jim Walter Corporation, has 5 underground coal mines in Central Alabama varying in depths from 400-2500 feet. Gas Chromatography plays a vital role in safety and production at each mine. Chromatographic data is used to monitor working areas for safety and proper ventilation and to control the quality of extracted methane for sales purposes. Instruments have a1 so been employed during mine rescue operations. JWR's first Gas Chromatograph (GC) was installed in April 1984 to monitor gob gas taken from longwall gob areas and sold based upon BTU value. The GC allows maximum extraction rate of the gas within the quality guidelines. By late 1985, another system was purchased and both units were upgraded to perform an analysis of indicator gases which may appear during mine emergencies. Each unit has the ability to detect and measure the following gases at almost any level ; Oxygen (021, Nitrogen (N2), Methane (CH4), Carbon Dioxide (C02), Hydrogen (HZ), Carbon Monoxide (CO) , Ethylene (C2H4), Ethane (C2H61, Acetylene (C2H2) and a composite of hydrocarbon threes and above (C3+). The analytical run is accomplished in less than ten minutes and is completely automated. This report will introduce Gas Chromatography as applied by Jim Walter Resources for the analysis of underground mine air.

Jan 1, 1987

By William Gleason

"Once the primary fuel source for the United States and the economic backbone for communities from Appalachia to Wyoming, coal has been on a steady decline since the mid 1990s, and is now at the center of political debate in the United States.The political spectrum of the United States is divided on the future of coal and its place in the energy sector. The coal mining industry and the communities that rely on coal have increasingly been pitted against forces that wish to regulate coal to the history books.In 2008, President Obama launched what many have called his war on coal, and during his eight years in office, he pushed through numerous pieces of regulations and legislation and that he said were aimed at reducing carbon emissions, but that others viewed as direct assaults on the domestic coal industry. Obama led the United States delegation to Paris to sign the Paris Accord in 2016, a 196-country agreement pledging that the United States would do its part to reduce carbon emissions. His administration also instituted clean air, power and water regulations that added extra environmental burdens to many industries, but perhaps none more so than the coal industry.In this month’s lead feature, “A study of U.S. coal mine closures since 1994” (page 18), the impact of the war on coal, and other factors, can be seen in text and figures. Author Jacob Brinkman and coauthors Jay Schafler and Catherine Johnson scoured the data of the U.S. Energy Information Administration (EIA) and the U.S. Mine Safety and Health Administration (MSHA) to show how coal production and mines have been impacted since 1994 and how the years 1994 to 2000 and 2008 to 2016 were particularly hard on the industry.For example, in 1994 there were 2,354 coal mines in the United States. Currently, there are 1,035 mines in operation.In 2016, then candidate Donald Trump promised to end the war on coal and to put coal miners back to work. In 2017, President Trump has followed up on those promises. He announced plans to withdraw the United States from the Paris Accord, signed an executive order designed to undo the Clean Power Plan put in place by President Obama, halted the research on the health effects of mountaintop removal coal mining, directed the U.S. Environmental Protection Agency (EPA) to revise the guidelines of waste water from power plants and has touted that more than 1,000 coal miners have returned to work since he was elected."

Jan 9, 2017

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur at around 1.5 per year between 2009 and 2021. To date, a standard methodology for the design of coal rib supports that can accommodate the wide range of unique conditions found in coal mines in the USA has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems’ effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff is proposed, beyond which the addition of primary support cannot stabilize the failed rib structure.

Aug 5, 2023

By E. M. Frizzell

Decisions affecting ground control design require detailed knowledge of roof rock geology. This is especially true when weak roof materials and anomalies create hazardous conditions and. if not properly supported, result in roof falls. The U.S. Bureau of Mines has developed a system to evaluate geological conditions by using a roof drill that will provide an estimate of the compressive strength of the roof rock in real time. Through the use of sensors and a microcomputer on the roof drill critical drilling parameters can be interpreted and analyzed almost instantaneously, making it possible to inform an operator of hazardous roof conditions such as voids and changes in strata during the drilling process. Geotechnical data can be downloaded to a portable semiconductor memory device, which is brought to the surface so that data can be directly accessed with a personal computer for further analysis. Results from field tests are presented.

Jan 1, 1992

The selected list of sources of information on geology and mining in this section is provided to facilitate locating the major governmental and private entities in position to furnish such information, including societies and institutes; colleges, universities and technical schools; and magazines, yearbooks and mine directories, plus a number of general texts. In the case of publications, it should be noted that, in addition to those listed, most of the governmental and private organizations publish a wide variety of reports, bulletins, monographs, surveys and the like, including, in the case of governmental agencies, production statistics. The names of the mining schools and colleges in the following, with some exceptions, were taken from the International Handbook of Universities and & her Institutions of Higher Learning, and the Commonwealth Universities Yearbook, with the kind permission of the International Association of Universities, Paris, and the Association of Commonwealth Universities, London, owners of the copyrights. Abbreviations in the listings include the following: A. P., B. P, and C. P., Apartado Postal, Boite Postal and Caixa Postal (post office boxes); Br., Branch; and F., Faculty.

Jan 1, 1973

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By Richard L. Bullock

INTRODUCTION TO COAL MINE PRACTICES To illustrate the trends and the proportions of the various methods used to mine coal underground, Fig. 1 is useful. However, of all the underground coal mining practices in the US, room-and-pillar mining still accounts for 96.5%. This percentage is divided as follows: conventional, machine cut-33.0%; conventional, hand cut -1.7% : and continuous mining-61 .8%. As was stated in Sec. 1, Chap. 7, the term "development" means different things to a coal miner and a metal miner. Though some of the ideas and concepts presented in the first two chapters of this section are valid for all types of mines, they apply particularly to mines using noncoal methods. In coal mines (and many other mines using coal mining systems) development refers to that phase of the mining cycle which advances several entries through the virgin seam, forming pillars by cross- cutting between the parallel entries. Because in the past, coal seams (as well as seams of potash, trona, oil shales, gilsonite, salt, and some uranium) have been much more uniform in their thickness, continuity, and quality, and because they often cover large areas, it has been possible to develop the room-and-pillar mine completely from a preplanned, systematic approach with a minimum of surface drilling information. As the better coal seams of the midwest and east are being depleted (or eliminated because of high sulfur), seams of poor quality and continuity will have to be mined. Also, seams that are not nearly so well known at greater depth will have to be taken as well as some of the steeply pitching and folded seams of the west. The American coal miner is only now feeling the need to do a much more complete job of prospecting the geology of the coal seams than he has ever done before. This is the only way that the risk of unknown rock conditions can be minimized. In many ways, surprises in the rock or coal seams are much more of a disaster to the coal miner developing a room-and- pillar mine than to his metal mining counterpart. Be- cause of the multiple entries, the complex set of the Federal Coal Mine Health and Safety regulations, and the totally dedicated design of coal mining equipment, coal mining systems do not have the flexibility to easily overcome changes in the seams mined or the rocks around them. Thus, if a wide parting of rock shows up unexpectedly in the middle of a coal seam entry being milled away by a continuous miner, it will either have to slowly "chew" through it, convert to a conventional mining system, or stop that particular entry. Likewise, if suddenly the coal disappears completely and in its place are the remains of an old creek bed, the "want" or "wash out" as it's called will usually have to be mined right along with the coal, by the same methods and with the same soft rock equipment, or the entry will have to be abandoned. For reasons such as these, coal seams today should be drilled from the surface just as thoroughly as the ore bodies in metal mines. Having once determined a more precise location of where the coal seams are located and which are suitable for mining, the engineer must still take a systematic approach to planning the mine as completely as possible. The initial series of entries must be planned to be driven either from the side hill portal or from the bottom of the shaft or slope. In either case, they should usually intersect the area close to the midpoint of the mass to be mined.

Jan 1, 1982

By W. Douglas Gould, Mei-Lin K. Stichbury, Jeffrey G. Bain, Blowes David W.

The mechanisms of release of arsenic in gold mine tailings were investigated. The highest concentration of dissolved As (75 mg/L) was observed near the base of the tailings impoundment, in close association with a peat layer. Elevated concentrations of reduced iron and hydrogen sulfide were also measured at the base of the impoundment. High numbers of iron-reducing and sulfate-reducing bacteria were detected at depths within the impoundment which correlated with dissolved As, Fe and H2S. The data presented in this paper suggest that arsenic is released from the tailings by bacterially-mediated reductive dissolution of As-bearing iron minerals.

Jan 1, 2000

By I. WILKOMIRSKY, J. BECKER, F. Parada

The current processes that aim to purify molybdenite concentrates are not able to dissolve some copper compounds, hence limiting the processes. Typically, the copper content results are from 2 up to 4 weight percent in the last concentrate. Such values are still too high for the molybdenite concentrate to be further processed to molybdenum trioxide by roasting. In order to achieve lower levels of copper — but also avoid excessive molybdenite losses — a continuous sulfation-leaching process is investigated and applied successfully on a pilot scale. Additionally, a reactor prototype and its process parameters are proposed for a commercial plant.

Jan 1, 2023

By M. SIDDARAJU, Rameshwar Sah, Satendra Kumar, Arvind Jaiswal

The study explores a novel process to sinter porous iron ore with improved productivity and quality. The iron ore is pre-processed with calcined lime to temporarily close pores, preventing water absorption during granulation. This enhances reaction kinetics and early slag formation during sintering, resulting in significant improvements in sinter productivity, product yield, and cold strength property.

Feb 28, 2022

By Evan J. Owen, Virginia T. McLemore

of high specific gravity, resistant minerals that form from mechanical concentration by waves, currents, and winds in marginal-marine environments. These sediments are enriched in critical minerals such as titanium, zirconium, and REE. Cretaceous beach-placer sandstones are found in the Colorado Plateau of northwestern New Mexico. Originally discovered by airborne radiometric surveys for uranium in the 1950s, these beach-placer sandstones are being re-examined with modern methods as potential sources for critical minerals. Selected beach-placer sandstones have been sampled, mapped with ground radiometric surveys, and analyzed with whole-rock and trace element geochemical methods. Mineralogy is being determined with optical methods, XRD, and EMPA. Zircon, rutile, ilmenite, and monazite are the primary heavy minerals of interest found in the studied deposits. Initial results show that the sandstones contain up to 1.4% total REE, 29.4% TiO2, and an estimated 4.9% ZrO2. Chondrite-normalized REE diagrams show distinct light REE and minor heavy REE enrichment, as well as pronounced negative Eu anomalies for each deposit.

Feb 1, 2024

By Bobby P. Faulkner

Allis-Chalmers has combined a new heat transfer device, called the ROLLER GRATE, with a unique processing scheme, resulting in the ROLLER GRATE Oil Shale Processing System of Allis-Chalmers. In order to test both the process and the equipment, a batch Process Development Unit (PDU) ROLLER GRATE retort was designed and built. This unit vas designed with the flexibility to process shale over a wide range of test conditions in order to demonstrate the attributes of the oil-shale processing system. Instrumentation on the PDU and extensive sampling of the effluent streams permitted the PDU test data to be used in the design and scale-up of the process. Over 30 tests have been conducted with Colorado shale, and over 25 tests have been run with an Indiana shale. In addition, rests have been run with California and Utah tar sands.

Jan 1, 1983

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, large-scale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in the city of Chifeng in China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading.

Jul 1, 2023

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, M. RAJU, GANESH SHETTY

With the depletion of high-grade iron ore resources, the utilization of existing low-grade iron ores, fines and tailings with effective beneficiation is inevitable to meet the iron and steel industry’s required specifications and demand. JSW Steel Limited is operating a 17-mtpa beneficiation plant at its Vijayanagar site in Bellary in Karnataka, which produces nearly 50 to 54 percent concentrate as sinter-grade fines. The sinter base mix consists of iron ore fines that are smaller than 10 mm, with 41 percent smaller than 0.150 mm; washed ore that is generally smaller than 3 mm and bigger than 0.150 mm, with 3 to 9 percent smaller than 0.150 mm; beneficiation plant concentrate, with 97 percent smaller than 0.150 mm; limestone; dolomite; coke breeze; lime; sinter return fines; direct reduced iron (DRI) fines; and micropellets produced from steel plant waste. Using more washed ore in the sinter base mix affects the sinter quality. Ball formation in the mixing and nodulizing drum is an important step in sinter making and requires sufficient quantity of smaller than 0.150 mm fines. Optimization of fines in the sinter base was carried out by replacing the smaller than 10 mm iron ore fines with washed ore. Size analysis, study of the granulation index (G index) and optimization of moisture with respect to sinter bed permeability were carried out to optimize the proportion of smaller than 0.150 mm fines in the sinter base mix as adhering material. This study explores the optimization of fines in the sinter base mix for ball formation to achieve higher sinter quality and productivity with higher sinter bed permeability.

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

By David A. Rice, Scott A. Shuey, William K. Tolley

The U.S. Bureau of Mines (USBM) is developing new dewatering technology to permit the recycling of iron values contained in wet steel plant sludges. In laboratory tests, Q-BOP fume sludge was dewatered to 12% moisture by displacing water with acetone in a plate-and-frame pressure filter. Acetone is reclaimed through distillation at lower cost than conventional thermal drying of the sludge. The projected additional energy requirement for acetone treatment of the sludge, including acetone recovery, is $5 to $7 per dry ton.

Jan 1, 1995

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986