Search Documents

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

The advantage of using ammonium phosphate salt as flux is the selective precipitation of chromium(III) compounds, which are considered nontoxic and environmentally friendly. The technique in this paper is determined to have potential to be applied in the metallurgical industry, where it can be used in the beneficiation of chromite mineral ores. The higher chromium contents of chromite ores often require furnaces to run at higher temperatures of above 1,300 °C, which can cause shutdown of the ore processing plant and accumulation of the sticky chrome compounds — including toxic chromium(VI) waste — which are generated as byproducts. The other advantage of this technique is its low to moderate energy consumption compared to existing techniques.

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By Elif Emil-Kaya, Bernd Friedrich, Merve Papakci

Samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are used in the production of SmCo permanent magnets, which have excellent temperature stability, corrosion resistance and oxidation resistance. Of the two types of SmCo magnets, one contains a high amount of iron, approximately 15.2 percent. This paper focuses on the recycling of iron (Fe)-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Jul 1, 2024

By L. Galarza

"INTRODUCTION Beneficiation of ores and minerals in a concentrator plant requires a significant amount of water [1] for the grinding and particle separation processes; most of it ends up being recirculated for reuse, slurry pumps are used after crushing and grinding feeding the ore to a classifier to separate fine-grained material (less than 5 mm) from coarse-grained material requiring further grinding. The lower ore grades [2] in the past couple of decades have demanded an increase on power size and efficiency of process machines to maintain a competitive plant throughput; Hydro-cyclone feed pumps to control both under and over milling or grinding are not the exception; Fig. 1 shows a conventional drive train [3] comprising an (1) asynchronous motor (also known as squirrel cage induction motor = SCIM), a high speed coupling (2), a gear reducer (3) and a low speed coupling (4) attached to the shaft of the pump (5), to accommodate the motor rated speed (typically 1800 rpm) to the process requirements (in the range of 250 rpm to 350 rpm), requiring additional components related to the gearbox: instrumentation, maintenance, disposable lubricants and filters, spare parts, thus reduces the overall system efficiency ultimately reflected into CAPEX and OPEX.WHY VARIABLE SPEED DRIVES FOR CYCLONE FEED PUMPS Hydrocyclones or commonly referred as “cyclones” are one of the most important devices in the minerals industry [4]; almost universally used in close-circuit grinding because of their high capacity and relative efficiency, the evolution of Power Electronics made affordable the use of Medium Voltage - Variable Frequency Converters (VFC) for Cyclone Feed pumps in combination with induction motors larger than 500hp (373kW) to gain multiple benefits: - Soft start with minimum electrical utility disturbance = inrush current mitigation - Full Torque available at zero speed for overload startup with pulp solidification after long still stand periods, superior to any other reduced voltage starting method. - Optimum and constant pump speed (independent of the electrical network or load condition), compared to across the line SCIM operation - Flexible Motor Voltage and Speed regardless of the power distribution Voltage and Frequency - Improved Power Factor (close to unitary), over the entire operating speed range"

Jan 1, 2015

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By Christopher J. Bise

The potential of the coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints which have tended to limit the development of these reserves which can only be deep-mined are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short- term the industry has to incorporate presently available equipment which were not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment that are in use today and their possible application to thick-seam mining. The paper also addresses the various ground control and safety considerations that are unique to thick-seam extraction.

Jan 1, 1981

By Yu-ren Jiang

Novel compounds of hydroxycarbamoyl carboxylic acids, including 2-hydroxycarbamoyl -3-methlcyclohexane carboxylic acid (HCMC), 2-hydroxycarbamoylmethyl decylen-4-yl carboxylic acid (HCDC) and 2-hydroxycar-bamoylmethyl tridecylen-4-yl carboxylic acid (HCTC) were synthesized. The flotation behaviors of diaspore, kaolinite and illite using these compounds as collectors were investigated. The flotation results revealed that the floatability of the minerals was, in descending order, diaspore and kaolinite, followed by illite, and the ability to collect the minerals was, in ascending order, HCMC and HCDC, followed by HCTC. At a dosage of 2×10-4 mol/L, both HCDC and HCTC show a strong ability to collect diaspore and a weak ability to float kaolinite and illite. The flotation recovery of diaspore is over 90% and that of kaolinite and illite less than 30%. Moreover, Fourier transform infrared spectroscopy (FTIR) spectrum and zeta potential, as well as the adsorption amount, indicated that the adsorption interaction between HCTC and diaspore was primarily a kind of chemisorption in the form of chelate rings, while the interaction between the collector and aluminosilicate mineral was dominated by physisorption. It was concluded that the novel hydroxycarbamoyl carboxylic acid compounds are highly selective collectors for the flotation of diaspore vs. aluminosilicate minerals.

Jan 1, 2011

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

Process plant modeling in the computer environment has been developed over the past 40 years by implementing the comminution models formed by the Julius Kruttschnitt Mineral Research Centre, University of Queensland, in the early 1970s. The models for the other processes in a mine value chain, such as blast fragmentation and flotation, were continuously developed and improved in parallel as well. Other research and commercial entities have also developed process modeling methodologies in the computer environment, which evolved as specialized commercial software or through equations set up in Excel spreadsheets. These were performed on a local computer, in thousands of simulations over a long period of time due to hardware limitations and the lack of a fully automated process. This limits the application of detailed process simulations for scale-up and strategic planning analysis, as they require many simulations to cover all possible scenarios which would take a lifetime when using local computers. The Integrated Extraction Simulator (IES), as the next generation of cloud-based software package, has made it possible to run simulations on the entire operation value chain in the same platform, including drilling and blasting, crushing, grinding, flotation, and other downstream process and material-handling units. This capability has allowed IES to handle multivariable simulations across the mine value chain, including pre-concentration and in-pit size reduction, and modify the process simultaneously.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By A. J. Benham, H. Kessler

In the UK a high proportion of land-won sand and gravel is extracted from sub-alluvial gravels and river terrace gravels located within river valleys. However, extraction from deposits of this type is increasingly proving to be less acceptable. Quarries within river valleys often have a high visual impact and the cumulative impact of these operations in close proximity to each other can be high (figure 1). River valley operations are almost always restored to open water. Whilst these may be attractive for nature conservation and provide leisure activities, they can also have a serious impact on the natural hydrology of the flood plain. Wet restoration of quarries located close to airports or airfields can also lead to concerns regarding increased risk of bird strike on aircraft. The Civil Aviation Authority recently suggested that an exclusion zone of 13 km be applied around all airports and airfields to reduce the potential for bird strikes on aircraft. This action is likely to have a serious impact on the availability of potential sand and gravel extraction sites in river valleys.

Jan 1, 2005

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

By A. J. S. Spearing, T. Kostecki, D. Benton

The use of paste backfill in room-and-pillar coal mines in the United States needs to be fully investigated. This paper discusses a series of physical tests that were conducted to examine the support benefits of theoretical paste backfill regimens in Illinois Basin room-and-pillar coal mines, which necessarily included consideration of weak floor conditions. The series of tests included those simulating strong floor conditions, weak floor conditions, under-confined scenarios, and testing of actual coal-based paste backfill samples. The testing indicated that a paste backfill regimen utilizing a minimum backfill strength of 22 psi at a minimum fill height of 50% of pillar height could significantly increase the longterm stability of coal pillars in the Illinois Basin. Considering typical coal wash plant recoveries, 50% fill would be feasible.

Jan 1, 2014

By P. Kolettas

The development of novel methods for the investigation of the subsoil contributes to the improvement of geotechnical research, enhances the obtained geotechnical characterization and may reduce the investigation cost by reducing the number of required tests. Non-destructive testing methods, performed either in situ (i.e. electrical tomography, seismic refraction, etc) or in the laboratory can provide initial data and perhaps estimates of rock/soil properties. This study focuses on the development of rock material properties and/or characteristics based on non-destructive laboratory testing of a number of stones, ranging from porous (bioclastic) limestones to impervious marbles. Seismic velocity measurements as well as attenuation signals were digitally recorded using a digital oscilloscope. Data were processed using a novel technique of spectral analysis available through special Matlab packages employing Fourier transform methods. More specifically, the NFFT (Non Equispaced Fourier Transform) transformation was applied to seismic waves traveling through the subsoil using the Autosignal program (by Seasolve) and the Specgramdemo program included in the Signal Analysis toolbox of Matlab 6.5 (Mathworks). Results indicate a definite relationship between the frequency content of the signal and the rock type as well as the degree of saturation of the specimen.

Jan 1, 2008