Search Documents

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

By Dewa Putu Agus Sudarmaja, Widi Astuti, Januarti Jaya Eka Putri, Yayat Iman Supriyatna, Himawan Tri Bayu Murti Petrus, I Wayan Warmada, Siti Nurul Aisyiyah Jenie, Ferian Anggara, Anisa Maulidia, Vincent Sutresno Hadi Sujoto, Sutijan

With the rapid development of renewable energy technology, such as electricity reserves, to store energy for electric or electric vehicles, environmentally friendly energy sources are expected to continue to be fulfilled according to mobility and stationary energy needs. Lithium is the most attractive candidate for energy storage development. The presence of lithium in Indonesia in the Sidoarjo mud content is interesting to be used as an alternative source of raw materials. During the research, sulfuric acid acted as a solvent, and hydrogen peroxide acted as an oxidation agent. Lithium recovery will be studied using a leaching process at various temperatures (30, 45, and 60 °C) and sulfuric acid concentrations (0.5, 1, 2, 3, 4, and 6 mol/L). The increasing temperature, sulfuric acid concentration, and hydrogen peroxide concentration will directly affect the lithium recovery. An increase in sulfuric acid concentration will be directly proportional to the recovery of lithium in the solution. Optimum conditions were obtained at varying 6 mol/L sulfuric acid concentrations and 60 °C temperature variations. The shrinking core model (SCM) studied leaching kinetics, and ash layer diffusion acted as a rate-controlling process. The activation energy of the leaching process was obtained at 38.90 kJ/mol.

Jul 25, 2023

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By Todd Loudin

A majority of the chemical process industry uses lime in either a powder or liquid form. Engineering and maintenance personnel often face a long and potentially expensive trial-and-error period in order to find the best process equipment to handle lime. Limestone is mined from a quarry in the form of calcium carbonate (CaCO3). Then, it is crushed and fed into a kiln at approximately 1,093° C (2,000° F), where the carbon dioxide is burned off (calcining) to make calcium oxide (CaO).

Jan 1, 2010

By John Chapman, Daryl Hockley, Michael Paul, Silvia Jahn

As part of the waste characterisation program to address site reclamation, WISMUT GmbH initiated 56 columns operated as large-scale humidity cell tests. The columns were initiated to assess the acid generation characteristics of waste rock from 14 waste rock piles distributed around the site. Of the 56 tests, 11 are ongoing and have been operational in excess of 160 weeks. The results to date from these long-term tests are surnrnarised. In particular, the methods for, and importance of, establishing the availability of the carbonate neutralisation potential and acid generation potential respectively, are discussed. Geochemical controls on uranium, and the conformity between the geochemical models MINTEQA2 and EQ3/6 in assessing these controls are discussed. Testing indicates that waste rock with an MS-NP:AP ratio in excess of about 2.7 should result in net neutral pH conditions.

Jan 1, 2000

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today&apos;s cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By Greg Barfoot, Kurt Keskimaki

The Henderson Mine is located approximately 50 miles west of Denver, Colorado. A project is underway to replace the existing rail system which transports molybdenum ore 15 miles from the mine to the mill using three flight conveyor system. The first conveyor is a 1 mile, high lift conveyor which transports the ore from an underground crushing station to the end of the existing rail tunnel. The second conveyor is 10 miles in length and utilizes the existing rail tunnel to transport the ore from the mine, which is on the east side of the Continental Divide, to the mill located on the west side. The third conveyor takes ore from the tunnel portal to the mill through a series of 7 horizontal curves and inclines up to 15 degrees. The project applies advanced conveyor design to tackle the installation of the system in an operating mine and achieve the highest possible level of reliability. This paper outlines the design process for this system, discusses the options which were evaluated and how the current design evolved.

Jan 1, 1998

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

This study used artificial neural networks (ANNs) coupled with Gaussian mixture modeling (GMM) to analyze truck haulage data from openpit mines. The proposed weighted ensemble models performed better than benchmark models in predicting truck productivity, providing a new means of solving complex data and improving mine planning and decision-making.

Jun 1, 2023

By Ernest Y. Baafi

This paper describes the results of a series of comparative studies in which polygonal, IDS, and kriging were compared for their local estimation accuracy. The specific objective of this study was to determine the impact that the particular nature of the mineralization has on the results of such comparative studies. The study was performed on simulated coal deposits and the evaluation parameter chosen was the coal thickness. For this study, many conditionally simulated deposits having different degrees of seam thickness continuity were first developed. Each simulated deposit covered an area of 30,000 ft x 30,000 ft which was, in turn, subdivided into 100 mine planning blocks of 3,000 ft x 3,000 ft in size. Thickness estimation was made for these mine planning blocks using surrounding DDH assays. In all cases tested, e.g., from a perfect continuity to a complete lack of continuity in coal seam thickness, kriging gave the best estimates among the three, followed by IDS and polygonal methods. As expected, the relative efficiency (i.e., superiority) of kriging over other estimators was highly dependent on the nature of mineralization.

Jan 1, 1982

By S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate as mines are being developed. In this study, finite element method has been used with optimization criteria to design more stable and safe underground openings.

Jan 1, 1993

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By Z. Zhongwei

The leaching kinetic of mechanically activated sphalerite with acid FeCl3 solution was investigated. The result has shown that mechanical pre-treatment has greatly enhanced the leaching process. Comparing with the original concentrate, the activated one can be leached more completely at relatively lower temperature with diluter FeCl3 concentration within a shorter leaching time. The activation energy for the activated concentrate is 27 KJ/mol, while for the original one is 52 KJ/mol.

Jan 1, 1995

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By R. V. Stewart

This chrysotile asbestos orebody is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 mi) north of Montreal; 480 km (300 mi) north of the tree line and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1/4 mi) in length some 61 m (200 ft) in width and plunges at 25-30 below surface to a vertical depth of at least 610 m (2000 ft). The orebody was originally evaluated by programs of surface mapping, diamond drilling and bulk sampling. The fibre is semi-crude, possesses excellent strength, and good fibre length distribution.

Jan 1, 1978

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan and a dispersant, under the trade name Pennfloat(TM)3. Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the uariables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors.

Jan 1, 1979

By Gill G. Geesey, Michael R. Hankins, Paul L. Wichlacz, Anita Gianotto, John G. Jolley, Randy B. Wright

Thin films of copper [2.0 nm on germanium internal reflection elements (IREs) and 3.4 nm on germanium discs] were exposed to 10% gum arabic (aqueous solution) , 2% alginic acid (aqueous solution), 1% bacterial culture supernatant (BCS, simulated seawater solution) and 0.5% Pseudomonas atlantica exopolymer (simulated seawater solution). The IRES were monitored in situ, in real time using fourier transform infrared/cylindrical internal reflection/attenuated total reflection spectroscopy as a function of time at ambient conditions. The discs were characterized (pre- and post-exposure) by X-ray photoelectron and Auger electron spectroscopies. Ancillary graphite furnace atomic absorption spectroscopy was used to monitor the removal process of the copper thin film from the germanium substrates. Results indicate that Cu was oxidized by gum arabic, alginic acid and BCS. Furthermore, Cu was removed from the Cu/Ge interface by all four polymers. The Cu was found associated with the polymer solutions.

Jan 1, 1989

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

By-products are of greater importance in lead and zinc mining than in any of the other major base metals. While I think most mining people would accept that statement, you would probably get some widely varying estimates when attempting to quantify the value of by-products in lead and zinc mining. We are now able to do this with our lead-zinc mine cost model. This model was originally developed as a zinc mine cost model to help us forecast long-term zinc supply and price as part of a study we completed in late 1979 entitled "Zinc - The Next Decade". Before demonstrating the importance of by-product revenue to lead- zinc mines, let me first explain how the cost model was constructed. I will discuss the model as it was originally constructed - as a zinc mine cost model. It has subsequently been expanded to include lead only mines and now can Be run either as a zinc or a lead mine cost model.

Jan 1, 1980

By A. B. Seal, C. J. Bise

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during the mid-1970s and mid-1990s consistently show that hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When the U.S. Mine Safety and Health Administration&apos;s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to reevaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Pennsylvania State University research project now being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2003