Search Documents

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By M. Li, J. K. Thompson, A. S. Azman

Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Pittsburgh Mining Research Division (PMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a tool to estimate in a systematic way the hearing loss due to occupational noise exposure and to evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software.

Jan 1, 2016

By B. N. Thompson

The main industrial minerals produced are non-metallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. The other minerals, some with minor production, include diatomite, feldspar, magnesite, sulphur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of Late Cenozoic acidic volcanic rocks.

Jan 1, 1982

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Josef J. Schwegel

The first vertical shaft lime kiln operating according to the parallel-flow regenerative principle was developed and built in the nineteen-fifties by Schmid-Hofer in Austria. Upon proving this concept of calcining or "burning" limestone to be very energy efficient for the production of good quality lime, Maerz Ofenbau AG of Zurich, Switzerland was in 1965 licensed for the design detailing and construction of these kilns. The first regenerative shaft type lime kiln outside of Austria was built in 1966 and through close co-operation with customers and their operating personnel, the advanced technical developments of today's kiln designs were accomplished. At present approximately 190 kilns of this type in capacities ranging from 60 to 700 short tons per day have been built or are under construction throughout the world in highly industrialized as well as less developed countries.

Jan 1, 1981

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By D. M. Davidson

The economics of geologic exploration have changed materially in the past decade primarily due to the change in three basic factors, namely, increased wages and salaries, increased cost of materials, and a greater complexity in methods of exploration. Following the general economic pattern over the past ten years, exploration costs, have, in general, increased, although there is one heartening exception. A comparative picture is complicated because of advances in techniques which ensue from the introduction of new methods and devices largely for aerial exploratory work, Some of these methods were either in their infancy or unknown before World War II. Geological exploration may well be considered as a form of applied research. True, it has peculiarities from this standpoint some advantageous, others disadvantageous, Some of the advantages lie in the fact that exploration success does not involve the production of a new product which necessitates advertising expense and marketing problems. In normal times there is a well established market for the fruits of a successful mineral find. The outstanding disadvantage of exploration lies in the enigma of deciding when to quit if the sought fop prize is elusive. In the search for buried treasure, man?s curiosity is apt to color his judgment. Even the so-called detached scientist may fall 'all too readily into the wishful thinking of the old- time prospector who is lured on by the thought that the next pull from the drill hole, or the next round from the face will reveal a bonanza. It involves mature judgment and experience to ascertain the stage in exploration when further work is not justified.

Jan 1, 1958

By P. R. Wotruba

The Fortitude gold-silver deposit is related to a "wallrock" copper porphyry system developed within Middle Pennsylvanian to Permian Antler Sequence rocks adjacent to a Middle-Tertiary altered granodiorite intrusive stock at Copper Canyon. Gold-silver ores of the Fortitude deposit occur with disseminated and massive sulfide replacement mineralization of skarn-like or calc-silicated limy horizons of the Antler Sequence contact meta-sedimentary rocks. A major, north-trending, steeply westward dipping normal fault was important as a conduit for hydrothermal fluids responsible for the metallization in the Fortitude area. Gold-silver mineralization is best developed near a marble front where retro-grade chloritization and destruction of prograde calc-silicate mineral phases is most prevalent. Fluid-inclusion studies performed on the Copper Canyon system indicate a wide variation in fluid chemistry during several hydrosilicate stages that ranged in temperature from 500°C to 220°C.

Jan 1, 1986

By T. M. Jones

This paper outlines the development of the theory of controlled district recirculation and indicates the advances in understanding and technology which have enabled a major change in established ventilation practice. An insight is presented into the possible future use of controlled district recirculation as acceptable practice in mine ventilation planning.

Jan 1, 1987

By D. C. McLean

Early studies in the carbonate leaching of uranium ores led to the investigation of pressure leaching as a method to enhance the dissolution of the metal values in this system. The initial investigations conducted at the University of British Columbia supplemented by the work done by the group at the A.E.C. Grand Junction pilot plant, all established the higher efficiency and better economics of the alkaline pressure leaching system. This work was conducted either in laboratory autoclaves using oxygen overpressures, or in pilot plant sized horizontal autoclaves with air as an oxidant. Both of these testing vehicles utilized agitation provided by relatively high speed impellers (300 to 700 rpm), which apparently enhanced the oxidation of the uranium to the hexavalent state. The installation of vertical autoclaves on a production scale, which through design considerations require relatively slow agitator speeds (68 rpm), led to the studies of the utilization efficiency of the air addition and the use of catalytic type oxidants to effect a greater usage of the oxygen added through the aeration system. In addition to investigating the effects of the chemical additives, studies were also conducted on the effect of different impeller configurations on the extraction of uranium, which in itself is a measure of oxidation efficiency. The material presented in this paper was compiled in the Ambrosia Lake district of New Mexico, and the majority of the data was obtained in the Homestake- Sapin Partners mill, located at Grants, New Mexico.

Jan 1, 1960

By J. R. Pennington

The town of Green River, Wyoming, is located along the Green River on an arid plateau at a elevation of 6,300 feet. Green River has become the center of a booming soda ash industry. The rapid development of coal, oil, and gas resources, coupled with the soda ash boom, have created growth pains for the area. Green River and Rock Springs have experienced a 20-25% population increase in 1973 alone. However, public officials, business leaders, and local citizens are taking positive steps to ease the problems relating to housing, schools, medical services, and recreational facilities. What Is Soda Ash? Soda ash is one of the most widely used chemicals in the world. It is an important raw material in the manufacture of glass, paper, soap, petroleum products, metals, chemicals, pharmaceuticals, plastics, and a host of other items essential to every day living. In ancient times, soda ash was obtained from water solutions of various desert earths. Later, it was produced by leaching the ashes of wood and seaweed. For the past 100 years, it has been manufactured by the ammonia-soda process, which employs large quantities of salt, limestone, and coal as raw materials.

Jan 1, 1974

By Michael H. Inglis

The Technology Application Center, in conjunction with the U.S. Bureau of Mines Liaison Program, is studying the use of Landsat data for the monitoring of coal surface mine reclamation activities. Landsat may provide sufficient information to reduce the number of on-site inspections now required. The focus of the project has been the Navajo Coal Mine located in north- western New Mexico and operated by Utah International, Inc. On October 15, 1977, a field team recorded spectral measurements at the mine during the time of Landsat's overpass and a corresponding aerial photographic flight. Training sets were selected from the ground and aircraft data representing vegetated, graded, ungraded and natural environments. A supervised classification of the data was performed by the Stanford University Remote Sensing Laboratory then correlated to aerial photos and mine maps. The results, to date, have been very encouraging.

Jan 1, 1979

By Peter Kreisman

This paper and four other papers on the MEQB Regional Copper-Nickel Study, presented today at the 1980 SME-AIME Fall Meeting are based on four years of extensive inter-disciplinary research and impact analysis supported largely by the Legislative Commission on Minnesota Resources. This study produced over 180 technical reports, the results of which are summarized in an Executive Summary available from the Minnesota State Planning Agency, St. Paul, Minnesota. Those wishing to examine the many scientific, engineering, environmental, social or economic issues addressed by the study are encouraged to obtain a copy of the executive summary. The executive summary includes a bibliography of all technical reports produced by the Regional Copper-Nickel Study and describes the five-volume, 26 chapter Regional Copper-Nickel Study Report.

Jan 1, 1980

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By N. Hoffman

Accurate, repeatable density measurements of a coal-magnetite-water slurry are difficult to achieve using a nuclear density gauge. Changes in the coal-to-magnetite solids ratio cause fluctuations in the readings of nuclear gauges. To investigate this problem the Electric Power Research Institute's Coal Cleaning Test Facility compared the performance of a nuclear density gauge on a coal-magnetite-water slurry with the performance of a differential pressure gauge modified with a new pressure sensor. A second aim of these preliminary tests was to determine if the differential pressure gauge is also sensitive to the type of solids in the slurry. This paper explains current slurry density measurement practices, describes the nuclear and differential pressure gauges used in the CCTF tests, and presents test methods and results.

Jan 1, 1986

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By Y. J. Wang

Editor's Note: Y.J. Wang's paper appeared in the September Technical Papers section. There were some inadvertent editorial errors in it. So we are reprinting it here. Abstract - This paper examines the ventilation network problem from a view point of solving a system of B equations in B unknowns, where B is the number o f branches in the network. Based on Kirchhoff s current and voltage laws, the solution to the general ventilation network problem must satisfy B network equations. In this paper, the air quantities and control-device pressures are chosen as variables and are grouped into B dependent variables (unknowns) and B independent variables, resulting in a system of B equations in B unknowns. Based on whether their variables are dependent or independent, the network branches are classified into f our types: five d, non-fixed, p-fixed, and q fixed. The ventilation network problem may include all four types of branches. There are .some conditions under which the problem as defined in this manner does not have a unique solution. To have a unique solution, the Jocabian matrix of the equations m us! he nonsingular. It then follows that: • the number of branches with independent air quantities must be less than or equal to the number of chords with respect to a spanning tree; •the subnetwork of branches with independent air quantities must not contain any cutset; and •the suhnetwork of branches with dependent control-device pressures must not contain any cutset. These three conditions must be met regardless of the values for the variables. In addition to the problem formulation, a solution procedure applying the Newton (or Newton-Raphson) method is outlined and illustrated with an example problem.

Jan 1, 1991

By R. C. Moe

Pelletizing studies were conducted to find ways of improving the metallurgical properties of acid and fluxed pellets. In acid pellets, melting temperature was controlled by the formation of low melting temperature fayalite during reduction. Formation of a permeable metallic shell during reduction allows diffusion of reducing gas to the pellet core, decreasing fayalite formation. With fluxed pellets, slag chemistry had the main influence on metallurgical properties. Mineralogical, chemical and structural transformations that occur during reduction were studied at various intervals for a number of Mesabi Range pellet types. Six pellet types were selected for further investigation based on significant differences in softening/melting characteristics. Retention of porosity in the metallic shell was found to be the overriding factor in determining softening/melting behavior.

Jan 1, 1990

By Malcolm D. Flavel

As indicated in the introduction to this paper, it is a sequel to that which I gave to the last annual meeting in Atlanta in march. This paper goes further into aspects of crushing and screening, primarily from the standpoint of circuit control. There has been little published by equipment manufacturers on this subject and this is the first paper on crushing circuit control to be sponsored by Allis-Chalmers corporation. By proper control over the use of crushing energy, we will be able to produce finished products from feed materials uti¬lizing minimum capital for the lowest cost of production. The subject will be discussed as follows. Firstly, we will look briefly at what we are trying to accomplish; Secondly, what is presently available in the way of technology; Thirdly, we will look at a suggested new system of control which will best fit the parameters of the normal crushing and screening operation; As a conclusion, I will summarize the advantages of the new system.

Jan 1, 1977