Search Documents

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By R. Kramer, A. Habibi

"Diesel Particulate Matter (DPM) measurements were taken at Tronox’s Westvaco Trona mine in Wyoming. Both shift-average and real-time monitoring using Elf pumps and Airtec analyzers, were used. The mine’s underground transportation fleet consists of more than 250 diesel-powered vehicles. A vehicle monitoring log tracked fleet usage during the test; logged data consisted of vehicle type, direction of travel, and time. The log was used in analysis to determine the DPM spread rate, of normally operating equipment, in the different entries with respect to vehicle location. Airflow velocity measurements at the stations were taken during the survey. The survey results also identified vehicles with higher emission rates. An ECOM gas and a MAHA DPM analyzer, both located in the mine’s underground emission shop, were used to obtain various vehicle emission rates. The correlation of the workshop and field measurements was investigated with regard to the machine activity, fuel usage and atmospheric conditions. The results were used to identify and execute a ventilation project to reroute 45% of diesel shop air back to intake entries, by interlocking an automated door and a regulator. The result is reduced DPM downstream. INTRODUCTION DPM has been classified as a potential occupational carcinogen by the National Institute for Occupational Safety and Health (NIOSH).The Mine Safety and Health Administration (MSHA) rule governing DPM exposures in metal and nonmetal mines cites total carbon (TC), a summation of elemental carbon (EC) and organic carbon (OC) obtained by NIOSH Method 5040, as a surrogate for determining DPM exposures (Noll, 2006). MSHA personnel use the 1973 sampling criteria outlined by the American Conference of Government Industrial Hygienists (ACGIH) for collecting compliance-based respirable and inhalation samples in metal/nonmetal mines. Instrumentation developments are allowing improved real time monitoring of ventilation parameters. DPM is within the aerodynamic particle size range of the samplers used for respirable and inhalable dust measurements. If a sampler used by MSHA to collect inhalable or respirable dust samples in underground metal/nonmetal mines was used to collect DPM, both the DPM and mine ore dust would accumulate on the sample filter (Noll, 2006). To comply with the requirement and lower the DPM exposure, mines are implementing a variety of control technologies such as emission based maintenance programs where adjustments or repairs are performed on the vehicles (McGinn, 2000)."

Jan 1, 2016

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation utilizing large draglines, trucks and shovels, tractor-scrapers, and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity, and distance, and to provide historical information for planning the most efficient and economic use of each equipment type in the mining operation. This report explains how the work order system was initiated, what data is tracked, and how the data is utilized for equipment and project scheduling.

Jan 1, 1994

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By William Gleason

"Caterpillar is the largest manufacturer of mining equipment in the world. In hundreds of surface mines around the globe, Caterpillar’s flagship 793 haul trucks can be found moving material for copper, coal, gold, iron ore and other mines. Likewise, its iconic yellow bulldozers are at mine sites the world over — the company recently announced the sale of its 40,000th large dozer. And since its acquisition of Bucyrus in 2011, Caterpillar has positioned itself to become a worldwide leader in the underground mining sector as well.But don’t think that the company is resting on its reputation. As evidence of its commitment to the global mining sector, as well as its confidence in the future of mining, Caterpillar invited mining trade press, including Mining Engineering, to its Tinaja Hills Training Center near Tucson, AZ in November to introduce the latest editions to its mining portfolio. The two-day event focused mostly on the newest electric drive haul trucks, the Cat 796 AC, which will operate in the 326-t (360-st) class, and the 798 AC in the 360 t (400 st) weight class.Caterpillar representatives also spoke about new offerings in the underground space as well as the newest version of the D11 large dozer.“It has been 10 years since we launched the F Series,” Jean Savage, Caterpillar’s vice president, surface mining and technology said. “Since then, we have been on a journey to serve our mining customers and we wanted to have trucks in every application. Today, we are launching two new trucks that will allow us to fill out our portfolio.”While Caterpillar previously offered the broadest range of off-highway haul trucks to the mining industry, it was noticeably absent from the 326-t (360- st) and 360-t (400-st) weight classes."

Dec 1, 2018

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By William J. Bryson

Just picture, if you will, the hot, lonely and desolate Ochre Mountains west of Salt Lake City. There works a grizzled old miner, his boots worn down, his clothes hang on a body stooped by years of hard labor. His skin is wrinkled and leather toughened by many years in the hot desert sun. His ever faithful burro stands patiently in the shade of a large rock as the tired old miner examines ore samples just acquired that very morning. Suddenly the old man's eyes widen, his breathing becomes rapid. 'Leaping to his feet, with a gleam in his eye, he cries, "Eureka, I'm rich, I've found the mother lode. This is where I will start my digging. " Without warning, the silent wilderness is alive with wild, shouting, charging figures! Frightened the old miner glances about him wide-eyed and pan- icky. His heart sinks, dismayed he now knows all is lost, this is the end. For there leaping from behind rocks and brush papers in hand, are the men from the Department of Interior, Bureau of Land Management, State Mine Inspectors, OSHA, MESA, EPA, OEO, and the never ending list of regulatory bodies related to todays mining industry.

Jan 1, 1975

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor's experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By J. Brent Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anoionic complexes, and faster leaching rates with acidic solutions of thiourea. Generally, the rate of metal dissolution in thiourea solution is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By Rajive Ganguli

There are several elements of online pedagogy and information technology that are being used in the University of Alaska Fairbanks’(UAF) course “ES 201: Computer Techniques,” to enhance classroom teaching. The use of information technology in this class grew from a desire to make lecture notes available to students. This has grown to include a sophisticated, online delivery software package. It provides chat rooms, discussion groups, and online testing and grading. Online delivery aside, the class uses the telnet, e-mail and C++/FOR-TRAN compiler facilities of the university server during class to enhance learning. During class, for example, the students read the lecture notes on the Web browser, telnet to their university Unix accounts, check their e-mail and download programs (to be covered in class) sent by me, and then compile, run and modify the programs. The class, therefore, requires students to be active most of the time. This ensures their full attention and better learning due to the hands-on experience (Fig. 1).

Jan 1, 2000

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

By S. Vivek

An Atomic force microscope (AFM) was used to measure the surface forces between hydrophobic silica surfaces. The measurements were conducted in the presence and absence of Cu(II)species in solution to study the effects of the cation adsorption on the hydrophobic force. The results obtained in the absence of the Cu (II)species showed that the hydrophobic force does not change with pH, while the electrostatic repulsive force changes substantially with pH. In the presence of the Cu(II) species, the hydrophobic force begins to decrease at a pH where Cu2+ions are hydrolyzed, indicating that the first hydrolysis product (i.e., CuOH+ions) are the species adsorbing on the surface of the hydrophobic silica. The results of the surface force measurements were used to develop a model for the adsorption of the hydrolysis product of Cu(II) species on the hydrophobic silica.

Jan 1, 2003

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008