Search Documents

By B. Ballard

Engineers at a West Virginia coal preparation plant owned by one of the nation's largest coal producers sought a fire suppression system for the plant's MCC and cable spreading rooms. Officials considered the traditional options of water-based sprinklers, dry chemical, and clean agent systems; however, each of those options presented challenges. Sprinklers can damage electrical equipment, proper delivery of the agent and adequate coverage/protection can be an issue with dry chemical systems, and clean agent systems require room integrity. An alternative to traditional systems was discovered in the Victaulic Vortex Fire Suppression System. The first hybrid inert gas/water mist system (FM 5580), Vortex adequately addressed these concerns. The system, which deploys a high-velocity, low-pressure mixture of water and nitrogen, is not damaging to electrical equipment and extinguishes fires in open, ventilated areas. This is one of the first installations of the Vortex system in a prep plant, and is a compelling example of how new technology can overcome the challenges of traditional technologies. The paper will detail plant specs, situation, and system evaluation, selection, and configuration.

Feb 23, 2014

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By S. Grogan

Next year marks the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). As the U.S. coal industry scrambles to cope with serious economic difficulties, it is appropriate to examine some other difficulties that have their origin in certain provisions of that ten year old law, and that bear directly on the economic viability of surface coal mining in the west. This paper focuses briefly on three technical issues in the reclamation of surface coal mines in arid regions, and suggests that innovation can resolve these issues. The coal industry operates within a narrow legal context, defined in 1977. In enacting SMCRA, Congress listed among the purposes of the Act ?... to...strike a balance between protection of the environment, agricultural productivity and the Nation's need for coal as an essential source of energy." I maintain that such a balance has never been struck, particularly with regard to the reclamation of mines in the west. One reason is that when SMCRA was enacted its supporters were aware of uncertainties about the potential for successful reclamation of western surface mines. Over the intervening years, as a recent Congressional study report (OTA, 1986) points out, "...the risks these uncertainties may pose to the long term success of western reclamation have been reduced significantly." Unfortunately, SMCRA's enforcement agency, the Office of Surface Mining (OSM) has not yet recognized this fact, and the western coal industry is paying the price.

Jan 1, 1986

By R. A. Matuszak

In recent years, a new concept in the control of electrically powered excavators has come into existence. The new type of control system has come to be known as "static" control. The use of the name "static" to describe this system is somewhat misleading since this term refers only to one of the many advantages of this very important advance in excavator control systems. In 1959, the first truly "static" control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the tried and proven rotating amplifier control system then in use, has since proven to be much more.

Jan 1, 1964

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By Richard Campbell, Claire Pirona, MEHMET KIZIL, Ismet Canbulat, Stephen Giese, Ravindu Goonawardene, Edward Steed, Serkan Saydam

The Australian longwall mining industry spends millions of dollars per year on proactive and reactive ground consolidation applications across most of the operations currently in production. The design and effectiveness of the applications and products vary widely and are based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. In the continual improve the effectiveness of how consolidation products are used and when by enhancing our knowledge of the mechanical properties of products used in underground coal applications and applying this increased understanding to geotechnical design. One of the current challenges to further developing more appropriate and accurate geotechnical design methods for consolidation activities is the lack of standardised materials testing and knowledge of rock mechanics data on in situ performance. The lack of industry standardisadesign of consolidation programs, with a reliance on experience-based guidance for rockmass consolidation design. consolidation products. The program was designed to provide the industry with a set of geomechanical property index tests and a data set that can be utilised by rock mechanics engineers as baseline information for product evaluation and engineering design. The laboratory work undertaken is critical to understanding the exact small-scale mechanical properties of these products and testing was carried out at Monash University for various states of curing of each product. Recognising that the speed at which a mixed product develops its desired properties to act as a support element in underground coal mines is critical to its serviceability. This paper presents the testing rationale proposed, the testing results, and a framework for how the data set can be used to improve the engineering basis for ground consolidation design, in terms of expected rockmass performance under various mining conditions and application parameters.

Jun 25, 2024

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

Researchers examined datasets from two separate studies that measured common demographic variables but different safety performance outcome variables. Of specific interest was how types of experience might relate to workers’ preparedness to effectively mitigate or respond to both routine and nonroutine risk in the mining industry. The results suggest that individual factors such as length of job, industry, and mine experience are predictive of routine safety performance — as measured by self-reported proactive and compliant safety behaviors — and/or nonroutine safety performance — as measured by perceived competence in self-escape knowledge, skills and abilities (KSAs) — in significant and sometimes unexpected ways.

By D. V. Ramani, M. M. Kissel, M. T. Ityokumbul

Experiments were carried out to determine the efficacy of bubble column flocculation. An acid-base neutralization method was used to determine the mixing time in a 0.064- by 1.5-m bubble column equipped with a Mottporous sparger. The mixing times decreased as the tracer injection point approached the gas sparger. Preliminary flocculation experiments on two clay samples were carried out. The effects of frother addition and airflow rate are presented and discussed.

Jan 1, 2000

By Joan Carles Casado Ortega, Mitchell Gerdtau, Sandeep Pyakurel, Eric Crocker, Frank Perrone

The Parallel Thimble Shoal Tunnel (PTST) project is a part of the Chesapeake Bay Bridge- Tunnel (CBBT) complex. The project involves the construction of a two-lane bored tunnel under the Thimble Shoal Channel between Portal Island #1 (the southernmost island) and Portal Island #2. The new PTST will be the rst transportation tunnel constructed in the Mid-Atlantic region by a tunnel boring machine (TBM). This paper describes the design and construction of the tunnel approach structure in an open marine environment with the strategies employed to overcome the various construction challenges. The project is unique since the entire tunnel approach structure is built on a very limited area within an open marine environment without any reclamation of the existing island.

Jun 23, 2024

By R. H. Olson

Pigments are used in two segments of papermaking, as the major component in paper coating formulations and, in small percentages, as fillers in the paper web. Historically, the dominant use has been in coating, however, recent developments have fostered a multifaceted effort to substantially increase the pigment component in the paper furnish. Factors responsible for these developments together with their relationship to recent and forecast changes in papermaking technology are reviewed. Finally, some thoughts are presented on the probable timing and extent of these changes as well as their expected impact on the future demand for the common paper pigments.

Jan 1, 1985

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By Vytas Svalbonas

Sophisticated computer analysis methods such as finite elements, finite differences, and numerical integration have become tools in the mineral processing industry for design of large mill shells. While use of such methods allows the analyst-designer to take new freedoms with his designed structure, there are also pitfalls and dangers which must be recognized for the proper use of such sophisticated tools. One of the worst of these is treating any computer answers as "gospel truth". The present paper discusses the knowledge required by the analyst-designer for proper use of computer analysis, as well as explaining to the layman how to identify questionable areas in such structural analyses.

Jan 1, 1979

By Richard O. Rouse

Today, I want to challenge this audience by charging each of you to be a greater manager and superior engineer to manage and engineer our way through the 1980's and profitably overcome all the present and proposed government regulations. May of the present and proposed regulations will tax you and your company's management and engineering to the brink of physical and monetary exhaustion, but I believe we can succeed and coal can be America's answer to her hungry energy needs. To put our 1980's challenge into perspective, I want to give two great challenges we must overcome. First - We must improve on our process of compliance to new government regulations in the technical and equipment end of our industry. The Lord said, "Let There Be Light". MSHA said, "Let there be light in underground coal mines". Since that time, we have lived through an unmanageable and tremendously costly period of compliance.

Jan 1, 1980

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project's design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission's design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat's three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission's design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission's Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By Vikram P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in terns of the compression strength, impact resistance (drop test), abrasion resistance and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder used. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1981

By William J. Miles, Raymond E. Blair

The oil and gas drilling industry is the largest user of "functional" industrial minerals for well drilling and completion. (Functional industrial minerals can be defined as those used for performance characteristics rather than composition.) This industry's use of industrial minerals involves complex mining, processing, and distribution of products. The cost of these products at the well site reflects the complexity of distribution to typically remote locations and the cost of service. Table 1 illustrates the use of functional industrial minerals by the drilling industry. The total tonnage shown is almost 2 1/2 times larger than the 3.3 Mt (3.6 million st) of kaolin used by the paper industry for filling and coating, another major use for functional industrial minerals. Drilling fluids are an indispensible part of a drilling operation. These fluids perform several functions simultaneously. They cool and lubricate the drill bit, remove formation cuttings, increase the specific gravity of the fluid to counteract formation fluid pressures, provide a filter cake on the wall of the drill hole to prevent drilling fluid loss to the formation, protect the porosity of producing zones, and prevent reaction of the formation or formation fluids with the drilling mud. When porosity of a formation exceeds the ability of the drilling fluid to form a wall cake, it is referred to as lost circulation. Because these fluids are being constantly formulated for changing formation conditions, they require a skilled technician or drilling mud engineer on the site at all times. Drilling fluids are composed of oil or water as the liquid phase, and industrial mineral products and chemicals to control chemical and physical properties. The basic function of viscosity and suspension result from the use of gelling clays and chemical and mineral dispersants; specific gravity of the mud is adjusted with mineral weighting agents; filtration control is maintained by clays and various natural and synthetic polymers; platey minerals and scrap products are used for controlling lost circulation in porous or fractured zones; salts are added to the mud to inhibit shale and clay swelling; chemicals are added for pH adjustment, prevention of corrosion, and as scavengers for formation fluid components. Because of the clay component, drilling muds have rheological properties different from conventional fluids, behaving as Bingham plastic fluids as opposed to the Newtonian behavior of water and oil. Newtonian fluids will begin to flow with the application of any force, however small. Bingham plastic fluids require a finite force or shear stress (yield value) before flow begins. Thixotropy is another property of clay-based drilling fluids. At rest they form a gel structure that suspends the weighting agents and rock cuttings. These gels break down when a finite force is applied and circulation is restored. At the bit where shear rates are the greatest, the viscosity or resistance to flow decreases, so hydraulic pressures and pumping costs are minimized. A drilling rig provides a means of rotating a hollow pipe attached to a cutting bit. A mud pit or tank is used for mixing the drilling mud and its components. A centrifugal pump delivers this fluid to the drill ripe and down to the bit

Jan 10, 1983

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015