Search Documents

By John C. Ferm

The role of geology in coal exploration, mine planning and mine development has, in the past, been relatively small. The primary reason for this lies in. the simplicity of geologic concepts that were necessary to bring these operations about. These concepts can be briefly stated as follows: 1) coal occurs in the beds or layers and is overlain and underlain by shales, sandstone or limestone in varying porportions, 2) each coal bed has been given a name and certain quality characteristics can often be associated with a named bed and 3) coal beds (and their adjoining rocks) are often folded into broad anticlines or synclines and, in some places, displaced or faulted. In actual practice, however, these simple principles have been found wanting. Thickening, thinning, pinch outs or changes in coal quality occurred but the occurrence was apparently unpredictable and the only real solution to such problems seemed to be practice and experience. This combined with ingeneous engineering solutions have provided answers to most questions. Perhaps a more fundamental reason that geology could offer so little input to coal mining is that the thickest, most persistant and best quality coal seams followed the above stated rules fairly well. In many areas, however, such seams are now nearing exhaustion and the increased demand for clean, non-polluting, safe energy is quickly bringing a need for techniques of exploration and mining procedures that will make development of formerly unminable seams a profitable venture. For the past 20 years some considerable body of knowledge has been added to the framework of the geology of sedimentary rocks and it is the purpose of this paper to present some of these newer ideas that will be useful in solving some of the present problems of coal exploration and development.

Jan 1, 1976

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By Howard Brown

High purity, high brightness limestone deposits in the San Bernardino Mountains and Mojave Desert region occur in upper Paleozoic carbonate rocks which are part of an upper Precambrian and Paleozoic sequence that unconformably overlies crystalline basement. The Paleozoic strata are divided into formations and members, and correlated with strata of the inner Cordilleran miogeocline. The region has been affected by multiple Mesozoic intrusive, contact, and regional metamorphic events. Structure is complex, and includes polyphase Mesozoic folding and thrusting, and complex Cenozoic structures. The area continues to be seismically active. High brightness (white), high purity crystalline limestone deposits are uncommon because their formation is dependent on several geologic processes which include; 1) depositional environment, 2) contact and or regional metamorphism, 3) folding and faulting, 4) uplift and erosion, and 5) preservation through geologic time. The complex geologic history of the San Bernardino Mountains and Mojave Desert region has allowed the formation of several large high brightness, high purity limestone deposits which are currently being mined or will be mined in the future. Specialty Minerals, Inc. (formerly Ptizer), Pluess-Staufer (California), Inc. and Partins Limestone, Inc. produce high brightness, high purity limestone from several quarries in the San Bernardino Mountains. These active mines combined with undeveloped deposits controlled by Pluess-Staufer in the San Bernardino Mountains, New York Mountains, and Bristol Mountains in the Mojave area, contain proven and or indicated reserves sufficient to sustain production through the 21st century Detailed geologic mapping, intimate knowledge of stratigraphy, recognition of complex structures, sampling, drilling and assay data, are proven tools in the discovery and delineation of high brightness, high purity limestone deposits in the San Bernardino Mountains and Mojave Desert region of southern California.

Jan 1, 1995

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By Y. Guo, C. Cao

"China is rich in tungsten resource, but they are mainly associated minerals. The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work summarized the current situation and the development of flotation reagents, technological process, and mineral processing equipments in China. Fatty acid served as the collector and water glass was the depressant to expand the flotability differences in traditional flotation technology. However the water glass inevitably influenced the flotation of tungsten minerals to a large extend, and the suppressed fluorite was difficult to recover by flotation. Abundant water glass lead to the bad settleability of the tailings and the tail water was difficult to circulate, resulted in serious environmental problems. Recent study proved that the selectivity of benzene armour hydroxyl oxime acid (BAHA) salts was adequate for the separation of tungsten minerals from fluorite, calcite and most silicate minerals without any depressant. By this way, sodium silicate was canceled completely in tungsten flotation, greatly improving the recovery of tungsten and the environmental problems caused by tail water treatment would be solved fundamentally. TUNGSTEN RESOURCES AND DISTRIBUTION IN CHINA China is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves [1]. However the wolframite has been dried up and the scheelite resources had become the main resource of the tungsten metal. Table 1 showed the most large and superlarge scheelite deposits in China. China has more than 40 large and superlarge scheelite deposits and the total metallic deserves is more than 3 million ton [2]. But most of the deposits were low-grade and the associated relationship was complicated. For example, scheelite was usually associated with wolframite, molybonite, bismuthinite, pyrite, fluorite, and calcite in Shizhuyuan and Yaogangxian mine."

Jan 1, 2016

By Ralph Loyd

One of the principal responsibilities of the California State Geologist is to provide local governments with maps and information regarding mineral resource occurrences within their jurisdiction. The primary objective of this effort is to furnish basic data that is essential in planning for and accommodating wise development of mineral deposits that are important to the economic well-being of the region, state, and nation. Local government agencies are required by law to incorporate the information provided by the State Geologist into their general plans and formulate mineral resource management policies that emphasize conservation and development of mineral deposits. The Mineral Land Classification program was initiated by the State Geologist in 1977 under authority of the California Surface Mining and Reclamation Act (SMARA). To date, about 33,000 square miles of land have been classified for mineral resource potential. Most of the mineral land mapping has been conducted in three principal areas: (1) metropolitan areas of the state where urban encroachment has greatly diminished available supplies of construction aggregate; (2) Sierra Nevada foothills, a region that is undergoing dramatic population increases; and (3) the Mojave Desert and Great Basin regions, where large Federal land withdrawals are pending that could preclude mining. Mineral land classification studies address the overall mineral potential of a region through the identification of local and regional geologic factors that control or influence the formation of mineral deposits. These studies are field-intensive surveys that enable project geologists to gain first-hand knowledge about the nature and distribution of mineral deposits in a given area and portray that information accurately in map form. This paper summarizes the progress made in the Mineral Land Classification program in the metropolitan, Sierra Nevada foothills, and the Mojave Desert/Great Basin regions of California. Selected projects from each area are discussed in detail.

Jan 1, 1995

By Leo Misagi

THE ROLE OF MANAGEMENT IN PLANT SAFETY Safe Production In plant management, safe production is an ideal. It becomes reality when: 1. Plant employees work in healthful and safe conditions. 2. Plant safety is in harmony with productivity. 3. Worker absenteeism and turnover are low-the work force is stable. Plant management must apply its talents, skills, and resources to build and maintain the foundations of safe production on a system of policies, procedures, and attitudes. It must do so by marshaling all managerial functions - staffing, direction, control, innovation, and representation-toward that goal. Ideally, a plant safety program is proactive. Management should plan and implement safety activities that are aimed at prevention. Past accidents-accomplished facts-should not be the sole guide of future actions. In other words, positive preventive measures, not the fewness of accidents are the criteria for safety production. An ideal safety program is one which is cost effective. Management should view plant safety as part of a broader program-loss control. Loss control includes prevention of fires and other accidents, unhealthful conditions, and occurrences that cause bodily injury, illness, property loss, or damage. Management evaluates the employees' productivity and safety. An effective training program aimed at loss control is the hallmark of safe production. Ideally, both labor and management should be well versed in safety. They believe in the premise that work-related injury and illness, as well as property loss and damage from fire and other accidents, are manageable and preventable. Such belief prompts them to learn more about the work process and potential hazards associated with each job. They also learn how to expect and prevent fues and other accidents, and respond to emergencies at the plant. Plant management determines which individuals or groups of employees are accountable for the following functions:

Jan 1, 1991

By Sam H. Patterson

The advances in knowledge of world bauxite resources in the last few decades include contributions to the geology of deposits, discovery of large resources, shifts in availability, and changes in. the industry in response to political and economic pressure. Improvements in the understanding of geology have resulted from the larger numbers of geologists working on bauxite and better exchanges of information. The large deposits discovered are mainly the laterite type in tropical regions. These discoveries have led to major increases in bauxite resource estimates as well as to shifts in bauxite availability and in the ranking of producing nations. Changes resulting from political, environmental, and economic pressures have resulted in increased costs of bauxite and in renewed interest in potential nonbauxite sources of aluminum. Aluminum is produced from nonbauxite raw materials only in the U.S.S.R.; however, research on extraction processes or investigations of nonbauxite alumina resources has taken place in several countries.

Jan 1, 1984

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Early rock-bolting practice usually consisted of ran¬domly installing bolts, using hand-held drilling equip¬ment such as air-leg mounted sinkers or stopers. As bolting technology evolved, the practice of installing uniform bolt patterns was developed, utilizing random bolt installation as required within the uniform pattern. The uniform rock-bolting technique, when used as the principal method of rock support, requires drills and jumbos designed specifically for rock bolting. This equipment is similar to conventional face drilling machines, except that the jumbos can orient the drills to obtain any necessary bolting angle; often, this means bolts may be installed at or near perpendicular to the centerline of the drift or stope opening. Fig. I shows a typical rubber-tired rock-bolting jumbo of the type commonly used in drifts and room-and-pillar mining. Modern rock-bolting jumbos are capable of drilling the required holes, inserting rockbolts, and torquing them to proper levels. Jumbos also are available for use with resin-anchored bolts. Probably the most unusual of this type utilizes a rotating bolt turret that carries the rock drill, resin charging unit, and the bolt in a single mechanism. Once the turret is loaded with the resin and bolt, further manual effort is not re¬quired. Drilling and bolt placement are accomplished by the operator from a station remote from the bolt site. Fig. 2 shows this turret device. Roof-bolting jumbos are available mounted on rail, crawler, or rubber-tired chassis. Various types of rock drills are used. Depending upon the type of rock, these may include rotary, percussion, or rotary-percussion drills. Fig. 3 shows a typical rail-mounted jumbo. CONDITIONS INFLUENCING APPLICATION General Rock Conditions Rock-bolting generally is applicable in moderately hard to hard rock. No particular type of rock is ex-

Jan 1, 1982

By T. M. Barczak, Zach Agioutantis

The Support Technology Optimization Program (STOP) has been developed by the National Institute of Occupational Safety and Health (NIOSH) to provide a comprehensive tool for evaluating the performance of available secondary roof support systems and designs based on support strength, convergence, cost, installation time and material handling considerations. This program uses engineering models developed from full-scale testing of numerous supports under controlled loading conditions in the unique NIOSH Mine Roof Simulator load frame to determine the support load-displacement performance as a function of the various sup- port design parameters. Both standing supports, such as wood cribs installed within the entry, and intrinsic supports such as cable bolts, can be evaluated. Support systems can be designed and compared for use in a new mining section or to evaluate potential replacements for an existing design. The support design requirements are defined from 1) estimating the failure height in the immediate roof, 2) in-mine measure- ments of support and strata interaction or development of ground reaction curves from numerical modeling, 3) the performance of an existing support system, or 4) from any arbitrary load and convergence criteria. All settings can be saved to permit resuming an evaluation in progress at a later time. This paper presents the updated MS Windows version of this tool, which can be easily installed and run on a personal computer. This Windows implementation will feature a project and application scenario setup where multiple scenarios can be assigned to one project. Scenarios can then be compared on support parameters and cost. Cost parameters can be provided either as individual cost items or using a price grouping feature. Additional support performance curves and/or additional ground reaction curves will be distributed with program updates as new information is developed. Users can also provide their own support and/or ground reaction curves.

Jun 25, 2024

By Elliot Gillerman

The title of this paper implies the presence of silver, nickel, and cobalt minerals at, the Alhambra mine. Perhaps this should be amplified to include uranium, as pitchblende also occurs, possibly in mineable quantifies. A brief history of the Alhambra mine is of interest, both from a historical angle and as pointing up the importance of geology in the-present development. The Alhambra is one of several mines in the Bullards Peak or Black Hawk dis¬trict, ass it is more familiarly known, in southwestern. New Mexico, which was mined for silver in the 1880?s and 18901s, Silver valued between $500,000 and $1,000,000 was extracted from the mine in the 10 years prior to 1893, when operations ceased. Almost all the silver mined was native silver, although a small quantity of argentite was produced. Nickel and cobalt were recognized in the ores, but they were thought to be of no consequence.

Jan 1, 1959

By D. C. Mahon, P. G. Sagert, M. R. Legeyt

INTRODUCTION Public opinion, over the effect of industrial development on the environment, has required government to institute guidelines for the protection of the environment both during the development of and after the decommissioning of mines. In no other area of mining has this requirement been more consistently applied in recent times than in the development of uranium mines. Uranium mines have been a focal point because of the very real uncertainties associated with the detrimental effects of radionuclides and the possible hazards of radiation. In order to determine if there is an environmental effect caused by a development or the storage of the mine waste as tailings, it is necessary to know what the quality of the environment was prior to the production of the tailings. This is the reason for baseline data programs. It is neither technically nor economically feasible to completely define the environment in any given region. Therefore, judgement decisions must be made prior to the development as to what aspects of the environment are more likely to be affected by the presence of the tailings, and to what degree. These decisions have evolved over a period of time based on information generated from existing facilities, scientific research, and the development of strong public opinions. This process is not static, but evolves with the growth of information and the technological developments which permit greater control of industrial pollution and waste management. A well-designed baseline program will reflect changes in science, technology and public attitude, even in advance of government regulations to enforce policy changes. RATIONALE FOR PREOPERATIONAL BASELINE STUDIES There are three distinct phases to be considered in the construction of an environmental assessment for a uranium mine tailings containment facility. I. Pre-operational 2. Operational 3. Post-operational (decommissioning and long term).

Jan 1, 1980

By Staff

Assembling consistent data for a 40-year time series is a challenge because of the many changes that have occurred in this period. In many cases, because of process improvements and consumer requirements, grades of materials change in a 40-year span. This can lead to a wide fluctuation in price data simply because of increased costs for premium grades. Sources for obtaining price data can also change during a 40-year period. Changing the data source also introduces anomalies in a time series. In some cases, published price data are not representative of the real value of the material and provide little basis for further analysis. For some industrial mineral commodities, there are only a few producers, and value and production data are considered proprietary. In the data presented in this chapter, every attempt was made to ensure that the data were as consistent and representative of the industry as possible. However, the factors mentioned above may have introduced inconsistencies in some of the data series. Many different factors influence trends for industrial minerals because of the diversity of end uses for these commodities. Trends in production and prices for most of the industrial minerals can be related to one or more of the following: changing demand or technologies in end-use industries, development of new end uses, the effect of environmental regulations, production and processing technology changes, energy costs, foreign competition and substitution by other materials, and production as a byproduct of other minerals. World economic conditions, such as recessions and inflation rates, also play a part in some production and price trends. Data for 40 years of production for industrial minerals in the United States are presented in [Table 1] in 10-year increments. Unit values for the industrial minerals, in actual and constant 1990 dollars, are shown in [Tables 2 and 3].

Jan 1, 1994

By K. Hanumantha Rao, K. S. E. Forssberg, F. Su

The influence of reagents dosage, pH, temperature, and particle size on the kinetics of apatite flotation response from magnetite has been investigated. The first-order models characterizing rectangular distribution and fast and slow distributions (F-S model) of floatabilities gave an excellent fit to the results of apatite flotation when compared to other models. However, the latter model is found to be better than the former in the goodness of fit and also in the description of flotation performance. The kinetic parameters in the F-S model are estimated by using a nonlinear least squares fitting program. The ratio of fast and slow rate constants is observed to be an important parameter for identifying the optimum levels of the variables and to outline the selectivity between apatite and magnetite. The influence of collector dosage is realized from the model parameters by relating it to the fraction of slow- floating particles. An attempt has been made to describe the apatite flotation behavior with the determined model parameters.

Jan 1, 1999

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995

By Anthony D. Hammond

INTRODUCTION A two-dimensional approach for modeling narrow-vein deposits using the TECHBASE® software was implemented at Sunshine Mining for its use in the evaluation of mineral properties. This 2-D approach prevents the overestimation of high-grade tons typically associated with the use of fixed 3-D blocks and reduces the size of the model in computer memory. The method consists of constructing a two-dimensional model oriented along the average plane of the mineralized structure. This approach works well for single, multiple and intersecting veins with the condition that each vein is roughly planar with variation in dip or strike less than 30" in order to maintain a reasonable resolution in the process of projecting data onto a plane (Figure 1). Also, a precise identification of the hanging-wall and foot-wall location is critical in ensuring an accurate representation of the vein. By using various modeling techniques, the two-dimensional model estimates metal content, thickness, tonnage, economic and dilution parameters which will be ultimately used in the identification of minable reserves. The following is a generic description of the steps involved in modeling a steeply dipping vein. DATA ENTRY A typical project database consists of drillhole coordinates, survey information, assay data and any other quantitative or qualitative data. This database can be created inside the software or imported from any spreadsheet. TECHBASE® utilizes the concept of "fields" and "records" (columns and rows) for storing data. The use of "calculated fields" enables the user to expand on the manipulation of the database with minimum memory requirements. Another important feature of TECHBASE® is the ability to replicate the structure and format of the "tables" for its use in another project and the capability of running a series of repetitive tasks by means of batch and "runlog" files.

Jan 1, 1998

By C. Orf. Chukabarah

Acoustic pollution (noise) is a significant mine environmental system problem. The U.S. Bureau of Mines (USBM), Environmental Protection Agency (EPA), Department of Labor (DOL) and other researchers have all performed contributory research on noise in mining environments. The present study addressed the problem of unavailability of a computerized, practical, routine, user-friendly, and user-editable, prose-styled application program with which one can determine (a) the noise exposure indices among mine workers, (b) mine system noise exposure level on time-weighted average basis, and (c) predictive relationships among mine workers' age, prior exposure to abnormal noise levels, prior auditory pathologies and the risk/degree of mining-induced hearing impairment. Results showed that such a program ("NEIL") is accomplishable. Additional results revealed that most U.S. mines operate within the statutory noise exposure levels. Furthermore, the mine worker's age was statistically confirmed to be the main predictive risk factor for mining-induced occupational hearing impairment.

Jan 1, 1992

By Gregory Witte

This paper will explore the technology behind and applications of smart motor control centers (MCCs) being used today in mineral processing facilities. The two technologies to be discussed are solid-state motor controllers that can be installed in MCCs and the complementary digital communication networks that can transmit operational parameters of the solid-state devices to the supervisory system. The toughness and reliability of solid-state technologies have led to a dramatic increase in their usage throughout the mining industry. Products such as solid-state motor protectors, controllers, and variable frequency drives have demonstrated greater flexibility and performance in a variety of applications than their electromechanical and mechanical counterparts. The three key trends apparent in the solid-state devices are: 1. A shift to smaller, smarter, more integrated devices, which allows a single solid-state device to serve the purpose of multiple electromechanical devices but in a much smaller form factor. 2. Distribution of control logic in motor control devices rather than conveyed through a hard wired connection to a central automation system. 3. Embedded network communication that allows supervisory systems to have an expanded view into critical loads and sensors. In applications, the use of smart actuators and sensors with integral local intelligence and communication allow a supervisory controller to send high level commands and let the smart device coordinate its own work The ability of smart field devices to return noncontrolled, nonpoled information opens a whole array of new capabilities for preventive maintenance and diagnostics and forms the basis for an effective motor management program. The smart motor control devices this paper will explore are the smart motor protectors (SMP), smart motor controllers (SMC), and variable frequency drives (VFD).

Jan 1, 2000