Search Documents

By H. Suharyono, R. Hogg, P. Bunnaul

The flocculation of fine-particle suspensions by polymers is a nonequilibrium process whose performance is strongly influenced by physical as well as chemical variables. A standardized test procedure has been developed that provides quantitatively reproducible measurements of process performance in terms of the floc settling rate, supernatant turbidity and sediment compressibility. The procedure provides information on the development of flocs in response to polymer addition and on their degradation behavior during subsequent handling. Extensive experimental observations using a variety of solids and flocculant types have been used to develop criteria for reagent selection and process design. It is shown that the appropriate choice of reagent(s) is determined primarily by chemical factors (solid type, solution chemistry, etc.). However, actual performance depends more on physical variables, such as agitation intensity and the rate of flocculant addition. Some general guidelines for flocculant selection and process design in industrial applications are suggested.

Jan 1, 1994

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners' protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981

By Ron VanRiper, Ben W. Burdett, Randy A. Ynchausti, Jeff D. McKay, Dan Lampshire, Thomas W. Toronto

An adaptive process control system was installed in Cortez Gold Mines Mill #2 Grinding Plant in Nevada. The installation, commissioning, and testing of the system took approximately 80 manweeks, but final test results show that the system paid for itself through increased throughput within two weeks of commissioning. Both crisp and fuzzy rules are used in the expert rule base which is also integrated with continually adapting neural network models. The expert rules and models are used by predictors, and optimizers to allow the control system to provide optimum process performance under continually varying feed conditions. The selection, installation, rule and predictor configuration, and statistically verifiable testing of the control system in the Cortez Gold Mines Mill #2 Grinding Plant is described in the paper.

Jan 1, 1999

By F. W. Brackebusch

Paste backfill is a pumpable, flowable, non-Newtonian fluid consisting generally of mine tailings and cement. Paste is prepared from dilute slurries of tailings. This is done by dewatering the slurries with conventional thickening or filtering. Backfill with a paste consistency is prepared by mixing dewatered tailings with cement and water to obtain the desired consistency of medium slump concrete. The paste is pumped with concrete pumps over relatively long (1 km or 0.6 mile) horizontal distances. More commonly, though, it flows by gravity down a mine shaft and then horizontally to the void being filled. Alternatively, cement can be added near the end of the pipeline. A certain proportion of fine particles <20 µm (<625 mesh) must be present in pastes but particles of aggregate can be added without significantly affecting the flow characteristics. Detailed testwork is necessary to design a system to prepare and place paste backfill. Testwork must determine dewatering characteristics, strength of mixes and friction in pipelines. Plants must be well engineered and controlled with PLCs because high quality control is necessary to prevent plugged pipelines and excessive pressures. Relatively small amounts of cement (3% to 5%) produce stiff backfill material 1.5 to 3.5 MPa (217 to 507 psi). The advantages of paste backfill in a mining operation include reduced mine dewatering, labor and materials savings, reduced tailings impoundment requirements, good support properties and reduced spills underground. In certain cases where more than 30% of the weight of the ore is sold as a product, the entire tailings stream can be placed underground. Paste technology can he used for surface or underground placement of tailings.

Jan 1, 1995

By Michel L. Van Sint Jan, Gabriel Fernandez-Delgado, Edward J. Cording, James W. Mahar

INTRODUCTION Shotcrete behavior observed in subway tunnel construction in the U. S. has been primarily in blocky or blocky and seamy rock in which rock loads develop from the self weight of individual rock blocks that tend to loosen from the wall and roof of the opening. Such conditions can be classed as loosening ground, in contrast to squeezing ground in which high pressures are generated on the tunnel lining with time as the ground creeps under the natural ground stresses. In the philosophy often associated with the New Austrian Tunneling method, emphasis is placed on the use of shotcrete and other support elements in squeezing, highly stressed ground, in which the support system is designed to allow controlled movements so that high lining stresses do not develop. In contrast to these conditions, the concern in loosening ground is to provide support soon enough to minimize loosen-

Jan 1, 1979

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By S. Slottee

The disposal of plant tailings in a safe and environmentally acceptable manner has taken on increased importance throughout the world, across all types of mineral beneficiation plants. In the U.S. plant life span, expansions and new plants in the current robust mineral markets are faced with environmental pressures to minimize the use of land for disposal by maximizing existing tailings pond capacity. The combination of many drivers from economic to environmental have brought paste thickeners into the coal industry (PasteThick 2007) Thickening tailings to a more concentrated slurry is a common step in the disposal flow sheet. Thickening to a non-settling ?paste?, also called ?thickened tails? or ?tailings stacking?, is a relatively recent development. This paper describes the paste thickener as an alternative for dewatering a fine coal refuse (tailings) stream for deposit as a paste. Initial operating results of the paste thickener are discussed.

Jan 1, 2008

By V. Avdiyskiy

The most pressing topic raised nowadays by the world community faces environment and social consequences of the business intensification process, primarily that of mining and mineral industry, which is through the number of its activities mostly associated with pernicious impacts. World top managers are confronted with the dilemma of reconciling traditional financial framework aiming at successful business development measured by revenues, shareholder value, profit margin and incorporating Sustainable Development (SD) at all levels of decision making process, avoiding depriving future generations of the means to meet their own needs. The rapid consolidation and globalization of the industry stipulates that companies are an integral part of the world economic environment. Therefore a company?s financial performance is under the pressure of operational and environmental performance. Among them special attention is paid to the social and economic background, the relationship with regulatory institutions, and the developments for environmental protection.

Jan 1, 2003

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By V. Angelatou

In the present study, the possibilities of use of natural zeolitic tuffs from the Skaloma area, Rhodope prefecture, Greece, for the removal of Pb and Zn ions from aqueous solutions has been studied. The equilibrium data were examined for different grain sizes, pH?s and initial concentrations. An apparent kinetic study was also carried out for different time intervals at constant temperature and pulp density. For the chemical equilibrium study the Freundlich isotherm was used. The experimental results verified the favored behavior of zeolite on lead ions and the quick kinetic of the process whilst the efficiency of the ion exchange on zinc is rather limited. The grain size of the material did not greatly affect the performance of the process. The removal of metal ions worked better at lower pH. The Freundlich isotherms are in good agreement with the experimental data.

Jan 1, 2006

By Chris Joyce, Peter Ryan, Graeme Mcllveen

This paper briefly summarizes regulatory procedures and government agency roles and jurisdictions in each Australian State and Territory. The role of the Commonwealth of Australia and selected current trends in environmental regulation are also discussed. While the Commonwealth has played an active role in regulating specific commodities or mines through its powers over export licences, international heritage agreements and the Territories, such cases have largely been a result of response to specific public issues. This may change; the Commonwealth has established the Resources Assessment Commission and is canvassing the establishment of an Environmental Protection Act, aimed at the standardization of environmental standards through the creation of an Environmental Protection Authority. While the States, the Northern Territory and the Commonwealth lwve nominally different resource planning, environmental project approval and operational regulatory authoritit:s, the fundamental principles hinge on mining lease, planning and pollution control approvals.

Jan 1, 1991

By Hugh E. Cronin, John Ramage

The recommendations resulting from a Dispute Review Board (DRB) hearing of a contract dispute are being challenged more and more frequently. This paper explores possible causes based on the authors’ experiences. Challenges facing the DRB process include: The DRB process is starting to lose some of the informality and flexibility. Both owners and contractors appear to be putting too much weight on a board recommendation on a dispute. DRB’s do not make “decisions,” they provide recommendations for dispute resolution to both parties. The DRB process is not just for contractors to present an unresolved issue to a board hearing. Owners can also initiate a request for a hearing on a disputed issue. For the DRB process to remain a viable element of the successful construction project, confidence must continue to be maintained in a process that is intended to work on behalf of both parties to the construction contract.

Jan 1, 2003

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

The dissolution kinetics of cobalt in iodine/iodide solutions was investigated using a rotating disc technique. Variables studied here included temperature, rotating speed, concentration of lixiviants, and pH of the solution. The overall dissolution reaction was found to be limited by mass transfer of tri-iodide through the diffusion boundary layer with Arrhenius activation energy of less than 16.2 kJ/mol (4 kcal/mol) over the temperature range, 2-42°C. The pH of the solution had little effect as long as the pH of the solution was less than 8. However, when the pH of the solution became greater than 8, the dissolution rate decreased dramatically due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1994

By Wayne Taylor, Martyn Dawborn

Simulation modeling of portions of two platinum mines using General Purpose Simulation Software (GPSS/H™) is presented in this paper. Both mines, located in the Bushveld Igneous Complex PIC) of South Africa, exploit Merensky and UG2 reef horizons, which are processed separately and therefore handled individually from the stope face to surface, requiring duplication of storage arrangements and batch operation of transport facilities. The first simulation assignment concerns the upgrading of a shaft system operating exclusively on Merensky ore, to hoist UG2 ore and increase production. The second assignment comprises a simulation of rock flow from the stope face to surface by way of tramming, inclined conveying and vertical hoisting. Development ends and stope boxholes were modeled down to individual hoppers (cars) demonstrating the versatility of the GPSS/H™ language.

Jan 1, 2002

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By Robert E. Barry

For new coal-fired power plants, federal regulations require that emissions of sulfur dioxide be limited to 1.2 pounds for every million BTU&apos;S burned. This is equivalent to coal with a sulfur content of roughly 0.7 percent for Eastern bituminous coals and roughly 0.6 percent for Western sub-bituminous coals. The states and their political subdivisions are free to apply more stringent standards and to develop implementation plans covering existing and new units. Most Western-sub-bituminous coals contain less than 1% sulfur and hence their use, in many cases, will allow a utility to meet the regulations. However, there are problems in using such coals in furnaces designed for Eastern bituminous coals, and furthermore it will take many years to open mines and provide transportation facilities to utilities which are now burning coals with a higher sulfur content. Moreover, pending federal legislation would outlaw strip mining on land to which the federal government owns the mining rights. Those utilities who, for one reason or another, intend to continue burning Eastern bituminous coals with sulfur contents in excess of 1 percent are faced with removing SO2 from the stack gases. The alternative of utilizing coal gasification where the sulfur is removed prior to burning in a power plant is still in the early stages of development. Therefore, a large number of processes are under development for SO2 control.

Jan 1, 1974

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978