Search Documents

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By Ralph W. Barbaro

In many parts of the country, electric utilities use spot market coal to make up the difference between the amount of contract coal and the total amount burned. The utilities involved will normally have a structured contract for those companies supplying that spot coal. These contracts will often involve a pricing schedule with bonuses or penalties for coal above or below the specified coal quality goals. Normally, penalties will be assessed on the sulfur, ash, and other coal quality variables. This paper deals with some aspects of the pricing schedule of one of the eastern utilities that buys coal on the spot market. This utility has a number of plants that a supplier can attempt to supply through bidding procedures. The existence of the pricing schedule gives the supplier a number of different options. To the single-mine producer, options are available to send the coal to any demand site and to clean all, part, or none of the coal. In other words, he can ship to a number of different sites and can send different coal qualities to each site depending upon the level of preparation. In addition, the options to deliver blended coal to any given site will provide an additional level of complexity to the problem.

Jan 1, 1983

By N. M. Levine

This work defines and systematizes the physical factors of the problem of leaching and demonstrates for the first time the utility of macropore volume, micropore volume, specific surface, pore size distribution and permeability as parameters of leaching based on a study of the recovery of uranium from the Top Black member of Chattanooga Shale.

Jan 1, 1962

By Prakash C. Kapur

A principal first order and a minor summation term contribute to the solution of the discretized batch grinding equation when formulated in cumulative retained mode. Depending on the interrelationships between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The implications and advantages of the reduced grinding equations are briefly discussed.

Jan 1, 1969

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By C. A. Rowland

With the rapidly rising cost for electrical energy and the long range pre¬dictions for continued rising costs and even possible energy shortages, operation of rod, ball, autogenous and partial autogenous grinding circuits to efficiently utilize the power delivered to the mills will be demanded. This calls for a method to evaluate grinding circuit performance that is accurate, reliable and readily usable as an operating tool by supervisory, technical and operating personnel. Neither the Rittinger and Kick theories of comminution,(1) which preceded the Bond Theory by more than 50 years, had a mathematical means that could be used to predict and evaluate the performance of crushers and grinding mills used to comminute ores and rocks. This severly limited the practical use of these two theories, which were contradictory to each other. They have been superseded by the Bond Third Theory of Commnution.(1)

Jan 1, 1976

By L. W. Saperstein

Surface mining of coal is undoubtedly one of the more controversial aspects of the mineral industries today. There is a constant tug between the need for readily available and inexpensive energy supplies and the desire to minimize disturbance to the land. Without a doubt, surface mining severely disturbs the land surface. The duration of this disturbance, from a minimum of a few months to a maximum of infinity, however, is strictly dependent upon the mine operator's willingness to reclaim. Surface mining critics claim that it is impossible to ameliorate the detrimental effects of this mining to insignificance. The more vocal critics, indeed, are calling for complete abolition of surface mining for coal. Thus, they do not believe that it is possible to restore surface- mined land to pre-mining conditions. As a consequence of this position, an adversary relationship has developed between the operators and their critics who, simultaneously, believe they are doing their best for the United States. In a forum of mining experts, there is little need to recount the kind and amount of devastation that can result from poorly reclaimed land. This has been done numerous times, including once 1 by the author. Of particular interest to this paper, though, are the environmental hazards associated with contour strip mining. In addition to the problems of area mining: denudation of vegetation; exposure of toxic spoil; increase of erosion runoff; etc.--contour mining has the very real problem of landslide due to the outslope stacking of overburden. Contour mining is understood to be the extraction of coal from a hillside outcrop such that the resultant pit follows, or nearly follows, an elevation contour. The problem with contour mining as usually practiced is that the spoil from the cut, or the first cut if multiple cuts are made, is placed on the outslope. If this slope is steep, the resulting pile is difficult to stabilize, generally erodes swiftly, and may fail disastrously.

Jan 1, 1973

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By T. Yukimasa

Hachinohe smelter, a zinc-lead blast furnace complex with the annual capacity of zinc plus lead of 100,000 tons, had originally treated normal zinc and lead sulfide concentrates. However, it is currently handling a great variety of raw feeds ranging from complex sulfides to oxidic recycled materials in view of resource economy, most of which are unsuitable for zinc electrolysis. This paper reports on some significant efforts recently carried out on improving sintering operation, i.e., the increasing use of secondaries against harmful ingredients like halogens, and the substantial reduction in energy use as the results of various modifications and improvements.

Jan 1, 1982

By A. W. Fahrenwald

The gyratory mill shown in Figures I and II is a ball mill in every sense of the term, in that the grinding media are balls. The media container, called the shell, is of the form of a shallow cylindrical tank whose position is with axis vertical The mechanism of the mill is designed to swing the shell in a circular path of small radius and, at the same time, to hold the shell in a position of constant orientation, i.e., the motion of the shell is such that every point on the shell surface -- bottom, wall and cover--travels in a perfect (horizontal) circle. The gyratory mill is definitely not a centrifugal ball mill. The balls do not, individually Qr in mass, travel in a circular path. Each ball, under heavy pressure from all directions, develops a sphere, or zone, of activity. Particles entering this sphere are crushed by impact. The gyratory ball mill, unlike the conventional tumbling mill, does not have, and is cursed by, a "critical speed". The speed of gyration, and in turn the power drawn by the mill--and ball potency--is limited only by the mechanical en- durance of the machine parts.

Jan 1, 1959

By Peter T. Chiang

A brief literature review on metal separations by ion exchange and solvent extraction of their thiocyanate complexes which are practiced in analytical chemistry as well as in industries was performed. Owing to the poor stability of free thiocyanic acid in acidic aqueous and organic media, technical and environmental problems which cause high thiocyanate consumptions often arise during the practice of the separation processes. This prompted the conducting of a second and more thorough literature review on the chemistry of thiocyanic acid. The objectives of this undertaking are to compile and interpret literature data on the physical properties and chemical reactions of thiocyanic acid, thus providing a clearer understanding of the causes of these problems and giving options as to how to minimize them. The best answer found for carrying out the separation processes is to keep the temperature, thiocyanic acid concentration and total acidity as low as practical.

Jan 1, 1984

By John H. Bassarear

By 1968 Cyprus Pima was milling 38,000 tpd of copper ore using a conventional flowsheet consisting of three stages of crushing rod mills and ball mills. A 15,000 tpd expansion was put on stream late in 1971 using primary crushing, semiautogenous mills, and ball mills. Identical ore is treated in both concentrators. This paper shows the weight and life of each individual liner for each crusher and each mill over a four year period from 1974-1977. Power and media consumption are shown for the same period and a comparison is made between the two reduction methods.

Jan 1, 1980

By J. G. Davis

Continental Oil Company has spent over four years of research on the fundamentals of potash solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well mining systems were studied in the field work. The current paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test. The potential economic value of solution mining has been recognized for many years, and applicable United States patents date back into the past century. Principal advantages of the process over conventional mining include (1) the use of drilled holes and solution techniques in- stead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths.

Jan 1, 1969

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By W. C. Meyer

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering math models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid chemical interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and predictions of the model are presented.

Jan 1, 1982

By V. I. Lakshmanan

Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market. Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogenous grinding. In addition to producing marketable coarse graphite by such autogenous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies.

Jan 1, 1984

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By George S. Koch

We evaluate the exploration effort by diamond drilling for zinc in central Tennessee and southern Kentucky through a statistical analysis comparing the Middle Tennessee district with the older Tri-State and Upper Mississippi Valley districts. All of the ore deposits are of the Mississippi Valley type and are similar geologically. Through statistical analyses we attempt to answer these questions: Had the drilling density in the Middle Tennessee district been applied to the Tri-State district, how much of the ore in the Tri-State would have been discovered? Had this drilling been done in the Upper Mississippi Valley district, how much of the ore in that district would have been found? Which of these two older districts does Middle Tennessee more closely resemble in intensity of zinc mineralization? Is more drilling warranted in the Middle Tennessee district? Our data base includes tonnage and area distributions of ore deposits in the Tri-State dis¬trict, sizes of ore bodies and probabilities of their recognition in the three districts, and data for the Elmwood mine in the Middle Tennessee district. Our statistical analysis considers the consequences of drilling holes in the three districts on square grids at coarse, intermediate, and fine spacings. We conclude that the drilling pattern assumed for Middle Tennessee would have found some but not all of the ore in the two older districts. We believe that in intensity of mineralization Middle Tennessee more closely resembles the Tri-State than the Upper Mississippi Valley district, and that more drilling is warranted in the Middle Tennessee district.

Jan 1, 1979