Search Documents

By Terry Ramsey, N. Finkelstein

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion I1 was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion I11 followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autogenous grinding circuit, is located in a separate building (Mill 11) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By S. P. Hansen

Gravity sedimentation is one of the most widely used processes for separating solids from liquids whether it be for ore and mineral processing or for treating municipal sewage or industrial wastes. Investment in sedimentation equipment can represent a significant portion of the total capital costs associated with a processing or treatment facility. In spite of the importance of sedimentation, little attention has been devoted in recent years to improving this equipment by applying the basic principles involved in sedimentation. In the water and waste treatment field, design criteria established one half-century ago is still the accepted standard and in reflection of this lack of progress, sedimentation and thickening equipment has remained virtually unchanged. The primary purpose of this paper is to present and describe a new innovation in gravity sedimentation which has been applied to water and wastewater treatment and could definitely have application in the field of ore and mineral classification. A secondary object is to introduce the mixed media filter which has been widely used to treat municipal drinking supplies, industrial process water and to provide tertiary treatment of sewage and industrial wastes. The tube-type clarifier was developed primarily to be applied in the field of water and waste treatment where it was found that it could be used to considerably reduce the size and cost of clarification facilities. A logical extension of the tube clarifier would be to the area of minerals classification, ore separation, and for treating waste water associated with these activities. In water treatment practice, most clarification processes are followed by a filtration step to provide further polishing of the water prior to use. This paper will also discuss the mixed media filter which is graded from coarse to fine in the direction of filtration and is capable of operating at high filtration rates and with greater applied suspended solids loading than other filter designs while providing a high qualify filtrate.

Jan 1, 1970

By Kent E. McElhattan

The selection of efficiency machinery for an underground mining system is a highly skilled art. Modern techniques of mining, based on sound engineering principles, increase the probability of success. These techniques alone, however, will not guarantee maximum productivity. Human judgement, based on experience with mineral seams and geological conditions, remains the single most important input of the decision-making techniques in selecting high production equipment. The myth of a "Scientific Selection Factor" is absurd. The belief that such a factor exists can waste the time and resources of mining management. Until now, mineral extraction from the original desposit has defied all attempts to systematize the knowledge. Computerized programs are excellent for solving underground transportation and ventilation problems. The variables can be defined by mathe¬matical techniques in this type of problem. By the same, token, "Trial and Error" is not an acceptable method in today's technology-minded world. The candid truth of the matter is that practically nothing is known of the phenomenon of extracting a mineral from the solid. Likewise, local conditions make it nearly impossible to predict accurately the reaction of surrounding strata after the mineral has been removed. The unpredictability of the environment resulting from extracting minerals underground will remain a challenge to mining engineers for many years. In fact, we are barely beyond the trial and error stage at this point in time.

Jan 1, 1969

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By Qiong Wu, Qinghua Gu, Yichuan Lv, Jin Yuan, Caiwu Lu

"The cut-off grade is one of the important parameters of mining production. Different material cut-off grade is directed to different destinations. Based on reasonable and optimal cut-off grade, long term mining plan and investment decision analysis can be made for mining managers. In view of multiple-metals open-pit, the paper has proposed that multiple-metals cut-off grade optimization model is set using the objective function to maximize net present value (NPV). The method of equivalent coefficient calculation is proposed to convert multi-metals cut-off grade optimization to a single metal cut-off grade optimization. Then the optimization model is applied in a molybdenum and tungsten large open-pit mine in china. The parameters of concentrate price are calculated by PRT in the model and the curve of grade-recovery rate is analyzed and studied according to actual production data. Based on 3D metal deposit model, the distribution of grade-tonnage is analyzed. At final step, an optimal cut-off grade is proposed to guarantee to maximize NPV. The example shows that the model of multiple-metals cut-off grade optimization can provide reasonable analysis for optimal multi-metals cut-off grade and develop optimal production strategies. Introduction Cut-off grade is one of the most important parameters in metal ore mining because of its influence on the overall economic profit of mining production. Along with the development of the mining production, dynamic optimization of cut-off grade is necessary through the analysis of technical economy. It is better to manage the mining production according to the variation of market. The cut-off grade plays an important role in mining production."

Jan 1, 2017

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

By Ian McFeat-Smith, Robert J. Fowell

Roadheader machines have a specific place in modern tunnelling, not simply as a compromise between drill and blast techniques and full face machines, but as an economic and versatile form of mechanised tunnelling where the method of excavation is easily integrated with tunnelling operations. In the past, roadheaders have been subjected to misuses by engineers who failed to realise that, as in all mechanised tunnelling, a planned and systematic approach is essential if the full potential of these machines is to be gained. An increasing awareness of this, together with the introduction of the more powerful roadheader carrying their cutting potential into the hard range of rock is changing this situation and now makes the prospect of using roadheaders particularly attractive (1). The advantages gained by employing these machines can be considerable and Table 1 lists some of them. This table illustrates that from both cost, and installation points of view, the roadheader has considerable benefits over the full face machine. However, the principal advantage gained is in broken ground where heavy supports can be installed immediately at the tunnel face. In addition, access for planned maintenance and repairs to most working parts of the machine is at a premium and average machine utilisations of 40 - 60% can be expected. In comparison to drill and blast methods, up to 40% better progress can be regularly achieved, and the subsequent savings in overbreak costs alone would more than pay for the cost of a roadheader used to drive a 3km long tunnel. As with full face machines, ground disturbance is minimal and for short tunnels in urban areas a road-

Jan 1, 1979

By R. Gradnik

The continuous need for infrastructure expansion forces the mining industry to develop underground structures into more sensitive and violent environments. When underground excavation enters into deep and high stress rock conditions, geotechnical designers find themselves faced with the difficult task of selecting a rock support system that will meet today's stringent requirements. Whatever support system is chosen, it is mandatory that potential rock movement be controlled. All this has intensified the development of safety systems and new, unique solutions which can enable construction companies to go both, further and deeper, without reducing the level of safety. To address these needs, Atlas Copco developed the Roofex® bolt, specifically designed to withstand large static and dynamic deformations under prespecified load conditions. The Roofex Rock Bolt acts as stiff support up to a designable load level before the sliding effect of the mechanical frictional system is triggered and allows highly controlled rock mass movement without loosing the support function.

Jan 1, 2011

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By Paul D. Bybee

The Freeport Sulphur Company operates four sulphur mines in the coastal marsh area-03 South Louisiana. Employing the Frasch process of mining, approximately 13-million gallons of water per day is heated to a mining temperature of 325°F and is injected into the sulphur bearing formations of the four mines. A volume of cold waste water, roughly equal to the Input, is removed from the formations and presents a disposal problem. Two additional mines are currently being developed and will increase the disposal volume by an additional 5-million gallons per day. Although these properties are in a relatively small area, geographically speaking, as shown in Figure 1, they each represent a separate disposal problem with the treatment methods designed for the individual mine.

Jan 1, 1959

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By Douglas R. Cook

Our present and future needs for base and previous metals are not satisfied by the present rate of new viable discoveries. This deficiency can be met by increasing the number of competent exploration organizations and by doing a more effective job of prospecting. My principal purpose is to show that new discoveries can be increased by improving the use of exploration techniques in a concept-oriented exploration program. Exploration techniques are defined and classified. The effectiveness of many exploration groups can be improved by better definition of objectives and thorough planning of the exploration program. The role of objectives, planning, and the use of techniques are discussed within the scope of the exploration framework. Common pitfalls in the use of exploration data are identified such as: inconsistency of geologic measurements, negative use of data, indiscriminate use of geo-surveys, collection of irrelevant information, and the unrealistic desire for exploration panaceas. Suggestions for improving the use of techniques include the use of multiple-working hypotheses, improvements in the quality of exploration data, use of geology in the selection, planning and interpretation of geochemical and geophysical surveys, and the recognition of variables and limitations affecting the interpretation of exploration data. The critical role of geologic mapping by Federal and State agencies is mentioned for satisfying the continual exploration demand for better geologic maps and filling many gaps that currently exist. The importance of imaginative and qualified exploration personnel is discussed as well as the maximum utilization of their exploration creativity. The problem of integrating field studies, research and training at universities and research institutions is identified. The need for high-quality research in economic geology is emphasized especially the importance of reducing the steadily increasing gap between basic and applied research.

Jan 1, 1968

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By Wilbur J. Morin

Construction of Flaming Gorge Dam in northeastern Utah necessitated the construction of a new state highway, Utah-260, to provide access to the dam and the town of Dutch John. A 550-foot arch structure was designed to span Cart Creek, about one mile southwest of the dam. The rock exposed at the site is highly fractured quartzitic sandstone with interbedded shale of the Precambrian Uinta Mountain Group. Eight exploratory holes were drilled, four in each abutment area, to determine rock types, the extent of fracturing at depth and rock strength. Drill cores in the west abutment revealed blocks of quartzitic sandstone loosened by the weathering and partial removal of underlying shale beds. The rock in the east abutment area was found to be highly fractured to depths of 70 feet and as far east as 50 feet from the footing locations. Selected core sections were tested for unconfined compressive strength but the values were not considered-representative of the in-situ fractured rock. To prevent movement along or, perpendicular to open fractures, four drilled-in columns were provided at the base of each footing. These extended 50, feet beyond the base of the footing, along the bearing and inclination of the thrust reaction.

Jan 1, 1963

By C. R. Montgomery

Coal companies in order to supply their customers En the metallurgical market, both home and abroad, must be able to control their production in order to meet carbonization specifications over and above those of the proximate analyses which has been the prime consideration of purchases in the past. It is the purpose of this paper to review in brief some of the tests used and give data to show the application of such as it applies to the customers needs. It is now recognized that coal is not homogeneous in any of its properties and an amazing fact is that it has been used for so long a time as the principal raw material for the manufacturing of coke without more emphasis having been placed on the variation between coals; yes, even from coals in the same seam at different geographical locations, Recently Kuchta and Clendenin pointed this fact out In a study of the(1) carbonizing behavior as related to chemical and plastic properties of Alabama medium volatile coal.

Jan 1, 1962

By A. K. Sinha

Inspite of the growing demands worldwide, thermal coal must compete in the market both in price and quality. The design and performance efficiency of coal preparation plants is thus crucial to the survival and profitability of a coal industry. While the coal recovery influences the cost of production, the quality produced by a preparation plant determines the selling price. Several coal preparation plant simulation models have been developed in recent years to help Improve the performance of coal preparation plants. A research project was recently conducted at Southern Illinois University to evaluate the practical applicability of such a model. The results of this study are presented and discussed.

Jan 1, 1986

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985