Search Documents

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By Tim Burgess

Patton Mining, LLC and J.H. Fletcher Company recently collaborated and mechanized the sometimes hazardous, and always labor intensive, process of installing standing steel supports during the construction of a slope entry of a new mine. The new innovation is a beam setting machine design that can lift and maneuver heavy steel beams into place over and around the belt and vent tubing. In addition, the machine is designed with an integral double extending lifting work platform to allow workers a stable work area from which to install metal sheeting between the beams. The previous method to install the heavy steel supports and the steel sheeting included multiple workers lifting heavy loads frequently on stepladders. This paper will inform the reader of how Patton?s major goal to develop the safest, most continuous slope development process possible was achieved and the beam setting machine that evolved from the project.

Jan 1, 2011

By S. S. Peng

The hydraulic powered supports have been employed in U. S. longwall mining for the past two decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. In order to improve longwall roof control and increase production, a series of questions in longwall roof control should be studied and answered: what is the basic rules of roof behavior in longwall coal faces equipped with the hydraulic powered supports? What is the interaction between the roof, supports, and the floor What is the contact condition of the canopy with the roof, and consequently the load distribution on the canopy? Des the periodic roof weighting really exist in the powered supported face and if so, how does it affect the face area? This paper presents the preliminary analysis of underground observations and instrumentations in a longwall panel with 4-leg shield supports designed to address the questions mentioned above.

Jan 1, 1982

By Yunqing Zhang

The 3-D numerical modeling using ABAQUS is performed to analyze the mechanisms of the tensioned bolts by taking into considerations excavation sequence, pre-tension, bedding planes and in-situ horizontal stresses. The effect of the pre-tension and the mechanisms of the tensioned bolts are analyzed based on the results from the modeling. Based on field observations, the failure modes for the tensioned bolted strata are classified by their causes and failure mechanisms. The support design consideration for each failure mode is given. Finally, a new design approach is proposed to do the tensioned bolting design using numerical method.

Jan 1, 2002

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By Kevin Andrews, Scott Nelson, Terry Hamrick

"In the process of Geologic Hazard Mapping (GHM) for underground coal mining, geologists evaluate the effects of various geologic and geotechnical conditions to assist with optimization of mine productivity and with selection of more favorable areas for future development. The methodology involves correlation of multiple geologic factors (such as overburden depth, proximity to sandstone channels, and areas with weak immediate roof strata) with conditions encountered during mining (roof falls, floor heave, pillar spalling, etc.). Such studies yield maps that identify areas where mining is likely to be difficult and allow mining engineers to foresee favorable and unfavorable mining areas when planning new or expanding mines. To expand the benefits of GHM, work has been done to correlate geologic factors with room-and-pillar mining advance rates. Average mining advance rates are mapped and then correlated to different areas, as characterized by GHM. This process exposes the geological characteristics that have a material impact on mining rates of advance, improving the rates of advance into future mining areas with similar geological conditions. The final result of the work allows mine planners to not only design the mine qualitatively accounting for areas of unfavorable conditions, but also allows the mine planner to more accurately apply rates of advance for mine timing and production sequencing. The use of GHM to predict mining advance rates in unmined areas enhances the benefits of traditional hazard mapping and provides quantitative data that can be incorporated into mine sequencing models.INTRODUCTIONThe role of a geologist in the coal mining industry has evolved significantly over the last 30 to 40 years. Geologic Hazard Mapping (GHM) mapping for coal mines began in the late 1970s and early 1980s (Chase, Newman, and Rusnak, 2006). Since its beginnings, the GHM process has evolved significantly and continues to take on new levels of sophistication. Numerous case studies of GHM application to predict future mining conditions exist in the literature. For example, Artrip, Nelson, and Newman (1993), documents the geotechnical characterization of roof and floor for mining in the Imboden Seam in Virginia where previous mining efforts had been abandoned due to adverse mining conditions. In addition, Keim and Miller (1999) summarize evaluation of geological influences on a longwall mine in West Virginia. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed."

Jan 1, 2018

By Roy H. Grau

The trend in underground room-and-pillar cod mining is to employ remote-control continuous mining machines to take extended cuts of 40 A or more. Roof fall safety hazards to the mine worker associated with 4ed cutting are not completely de6ned but are known to include removal of the miner operator from the protective canopy, non-compliance with approved cutting depth and CM operator positioning. This report summarizes ground control research performed by the National Institute for Occupational Safety and Health (?-JIOSH) researchers at the Pittsburgh Research Laboratory concerning extended cuts. A combination of statistical analysis and underground investigations have been conducted. Statistical analysis of extended cut use, along with roof fall accidents and fatalities data delineate the extent of the problem in U.S. coal mines. Additionally, an underground study is described where the long-term roof stability of extended cut areas are compared to standard cuts.

Jan 1, 1997

By Thomas L. Vandergrift

The type and severity of coal mine entry failures are affected by the strength and stiffness properties of the roof, floor, end coal. Knowledge of the mine-wide trends of these properties Is valuable in developing effective ground control plans. Within the context of a larger effort to Improve entry stability In high horizontal stress fields, the U.S. Department of the Interior, Bureau of Mines, has evaluated three portable, on-site test devices to determine their suitability for identifying mine-wide physical property trends. The devices evaluated were the borehole shear tester, the Schmidt harmer, and the point load tester. Despite the lack of standardized data Interpretation procedures, each device provided useful on-site physical property data. The Schmidt homer was preferred for trend identification because of Its speed and simplicity. Schmidt hammer data were collected over a large area of an underground coal mine to compare calculated roof strength trends with a known geologic feature.

Jan 1, 1990

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By David K. Ingram

The objective of this U.S. Bureau of Mines (USBM) investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored at two sites in southeastern Ohio. Site A included two adjacent longwall panels. Site B consisted of one longwall panel. Both sites had similar mine geometries and overburden thicknesses. The major difference between the two sites was the rock strata within the overburden. Multipoint borehole extensometers (MPBX) were employed to measure subsurface displacements. Survey monuments were installed above the centerline and profile of each panel to measure surface deformations. Subsidence of the surface was observed before and after movement was detected in the MPBX units. Initial and final displacement of the MPBX units occurred at the same time at both sites. No deformation was detected outside the panel area. The development of overburden deformation was different over each panel. The final subsurface failure characteristics also varied between panels.

Jan 1, 1994

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By H. Maleki

Gob pressure measurements were made in a Western U. S. coal mine as part of a long-term program to evaluate cave progress and to determine the influence of geological discontinuities on caving conditions, load transfer, and resulting instabilities. Gloetzl cells were selected for the measurements due to their simple, robust construction and a history of being able to monitor pressures in a broken medium. A methodology was developed for the successful installation and protection of the cells and hydraulic lines in the gob as the face retreated. The measurement indicated a cave progress controlled by the frequency of, major faults. The pressure-mining progress profile was compared to those observed in other parts of the world. It was concluded that the significant differences in profiles was caused by the thick-bedded strata, the existence of high lateral stresses and the spacing between faults. Recommendations are given for future applications of Gloetzl cells for gob pressure measurements.

Jan 1, 1984

By Larry Stolarczyk

The mining industry would benefit greatly by imaging geologic conditions well in advance of mining. In layered deposits such as coal, trona, quartz, and potash, natural waveguides form and enable electromagnetic seam waves to travel great distances. In the early 1980s, the Radio Imaging Method (RIM) was developed to capitalize on electromagnetic seam wave propagation in the assessments of seam conditions in longwall panels. The initial applications of RIM tomography and comparisons to in-mine mapping of geologic conditions proved that faults, paleochannels, and rapidly thinning coal could be detected and imaged with seam waves. This paper describes the application of electromagnetic seam waves in mapping the margins of a paleochannel crossing a longwall panel and the interesting possibility of adopting the newly developed Full Wave Inversion Code (FWIC) )Newman 1995) to significantly improve imaging resolution. When tomography images are combined with ground control science, a significant reduction in cost, roof fall potential, and waste rock in underground mining may be realized.

Jan 1, 1999

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Aleksander Wrana

"The Carboniferous coal measures, mined across Europe including the major European underground coal mining countries of Poland, UK, Germany, and Czech Republic, suffer from increasing extraction depth. This results in major geomechanics problems associated with ground control and support design.With production being concentrated into ever fewer high performance longwalls, located at greater and greater depth, pressure to ensure the roadways’ functionality (required dimensions) continues to increase. Mining in deeper and more highly stressed mining environments creates several problems. The high stress and deterioration in geological and mining conditions in many cases causes problems with gateroads maintenance (due to excess convergence). That leads to costly production gaps, longwall slowing, transport problems, an increase in the methane hazard and in the general health and safety of the workforce, and deterioration in climatic conditions with major economic risk associated with interruption of the revenue stream. Time—and thus production—delays due to maintenance often result from insufficient geological and geotechnical data acquisition and misinterpretation combined with inadequate support for the type of rock mass.longwall face on the gateroad stability (described by the gateroad convergence, support load, and shape and height of the fractured zone around the longwall gateroad) are presented. The investigations were carried out in the longwall panel with roof caving located at the great depth, in conditions of the Upper Silesian Coal Basin in Poland.The measurement results showed that the gateroad fractures in roof strata began to occur at the distance of about 1000 m ahead of the face. Additionally, the load on support and gateroad convergence increased as the longwall face got closer.It is very important for coal mining research institutes and mine operators to investigate and develop practical solutions and apply innovative support technologies at a great depth (particularly for reinforcement and stabilization of roadways and other openings).Underground measurements of stability conditions around the gateroad is of great importance to mining practice, especially in planning and designing supports for longwall gateroads.The influence of the front abutment pressure results in an increase of support load, gateroad convergence, and shape of fractured rock zone."

Jan 1, 2015

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Brian Clifford

A wide range of different cablebolt systems are available and in use in hard rock and coal mines around the world. The birdcaged cablebolt was initially used in UK coal mines in conjunction with rockbolts in the late 1980's. More recently other cablebolt configurations have been used. Innovations in cablebolt design in the UK have been driven by a demand to find a system as effective as the birdcaged cable, but which can be installed more rapidly and offer immediate support. A laboratory short encapsulation pull test (LSEPT) has been developed for both rockbolt and tendon systems which measures bond strength and stiffness in rock and assesses the full range of potential failure modes. This test is now used along with conventional 'gun barrel' and shear tests to provide full assessment of bolt and tendon performance. This test may be incorporated into a new performance based British Standard for rockbolts and long tendon systems. This paper describes the performance of some of these systems as being applied to UK and South African coal mines.

Jan 1, 2001

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By John P. Dunford

U.S. Bureau of Mines researchers are investigating the ability of mine-wide monitoring systems already in place at many coal operations to provide a direct link between geotechnical instruments and the mine-wide monitoring console on the surface. This paper describes a number of field tests using instruments such as-string potentiometers to measure roof-to-floor closure and bed separation and pressure transducers to monitor pillar loading. The advantages of using existing systems include on-site data collection and analysis, real-time understanding of geological conditions, and long-term data recovery from areas that have become inaccessible to mine personnel. However, because data are generated constantly, large files develop very quickly. In many cases, the data are redundant, such as during times of reduced mining activity or in areas not yet in the vicinity of active mining. To reduce the volume of data, a software program was written that eliminates unnecessary readings and generates a more concise file that can be output to a mine-wide monitoring system, personal computer, or as hard copy.

Jan 1, 1993