Search Documents

By Gregory A. Knapp

Treatment of industrial wastewaters generally advances with specific chemical concentration and mass-flow targets, established by National Pollutant Discharge Elimination System (NPDES) permits. Treated discharges must also address toxicity to test and receiving water organisms. Various parameters might need consideration during treatment design and planning, such as the known toxicants, hardness, alkalinity, solids, nutrients, metals in both the dissolved and particulate state, and even flow. Since toxicity is used as a "catch all" regulatory monitoring tool, design of treatment systems should focus on the various factors contributing to toxicity.

Jan 1, 1996

By Junhong Noh, Kug Sun Hong, Jung-Kun Lee, Bo Ding

"The photocatalytic splitting of water into H2 and O2 by oxide nanoparticles has received much attention. However, the full potential of photo-catalysts for efficient hydrogen generation out of water has not been fully realized yet due to unresolved limitations including the low electrical conductivity and ineffective carrier extraction. Here, we report composite oxide materials consisting of 1-dimensional (1-D) transparent conducting oxide (TCO) core and TiO2 shell. Highly conductive ITO nanowires were grown on a flexible SUS mesh as a core component. The photoelectrodes consisting of these 1-D nanocomposites have increased carrier mobility due to the TCO core, while the TiO2 shell provides the photocatalytic functionalities. In addition, the built-in-potential at the interface between TCO core and the TiO2 shell improves the collection of charge carriers from TiO2 to TCO. These factors altogether contribute to increasing the photocurrent of the device under light.I. IntroductionPhotocatalytic behavior of semicondcutors has been extensively explored since it was discovered in TiO2 in 197Os. When TiO2 is exposed to UV light, the light is absorbed and electron/hole pairs are generated in the conduction and valeence bands. Holes in valence band will oxide/mineralize pollutant target directly or indirectly (via mediator hydroxyl radical). If the adsorbed A is O 2, O 2 will react with electron from conduction band to generate hydroxyl radical as described in the second set ofreactions. The photocatalytic reaction is schematically explained in Figure 1.Photoelectrochemical (PEC) cells using the photocatalytic reaction have attracted emerging interest as a potential route to convert solar radiation into useful forms of energy by reaction such as water splitting to generate hydrogen1 or the reduction of carbon dioxide.2 Another application ofphotocatalysis is water splitting and CO2 reduction, both of which utilize the electrons that are optically excited to the conduction band. 3•4 For this purpose, the conduction level of the semiconductor should be higher than hydrogen production level (EHZ1HZO) while the valence band should be lower than water oxidation level (Eo21112O). Electrons and holes will be generated on the semiconductor site, and holes generate O 2 at semiconductor site, while electrons will migrate to counter electrode to execute reduction forming H2. In addition to that, materials should be chemically stable to resist photocorrosion and have long lifetime of electron/hole pairs. TiO2 is a suitable material from the viewpoint of band arrangement and chemical stability requirement"

Jan 1, 2012

By Fernanda de Paula, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Carlos Maurício. F. V, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Jan 1, 2015

By Weizhi Zeng, Michael L. Free, Sayan Sarkar, Prashant K. Sarswat

Black Phosphorus was recently discovered as a 2D material and it exemplified huge prospects for application in electronics, optoelectronics, photonics and catalysis. It is a direct band semiconductor with tunable band gap varying from 0.35 eV (bulk) to 2 eV (single layer). But the layer dependent band gap of black phosphorus restricts it to make use of the full spectra of sunlight for absorption. First principle calculations were performed using ‘Quantum Wise Atomistic Toolkit’ package with Perdew-Burke-Ernzerhof (PBE) exchange-correlation for black phosphorus doped with non-metallic dopants of B, S and Se and metallic dopants of Ti, Mg and In. It has been found that doping with non-metallic impurities result in a small diminution of the band edges (0.96–0.57 eV), whereas doping with metallic impurities decrease the band edge drastically (0.85–0.025 eV). Moreover, it was also observed that dopants with an even number of valence electrons incorporated a metallic nature of black phosphorus, whereas dopants with odd number of valence electrons further attributed to its semiconducting features. Thus in a holistic discernment, black phosphorus with the incorporation of some dopants in appropriate amounts can absorb more visible range of the optical spectra, making it ideal for use in photovoltaics.

Mar 1, 2017

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. In this work, thc potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (DW). Seven taxa are of Alyssum genus and one of Bornmuellera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mglkg or 2.5%) and Alyssum markgrafli O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By Jerome P. Downey

In the thermal treatment of electric arc furnace (EAF) dusts, zinc is reduced, volatilized, and ultimately recovered either as liquid metal in a splash condenser or as solid zinc oxide in bag filters. During the process, the duet's chlorine and fluorine content also enters the gas phase and condenses as dross in the splash condenser or as salts which contaminate the zinc oxide product. Pretreatment of EAF dust by pyrohydrolysis appeared to offer a means of minimizing the duet's halogen content. The primary research objectives were to experimentally verify the technical viability of pyrohydrolysis and delineate the process parameters requisite for efficient halogen removal. To this end, representative EAF duet samples were secured and characterized by x-ray diffraction, scanning electron microscopy, and Mössbauer analyses. Specific- experimentation focused on the response of halogen extraction to variations in temperature, retention time, water vapor partial pressure, and various additives. The experimental results proved that 97 to 99 percent chlorine extraction and 80 to 85 percent fluorine extraction are consistently achieved when EAF dusts are blended with silica and roasted at temperatures of 850°C or greater in a furnace atmosphere of 75% steam (diluted by air). A statistical analysis further established that more than- a single optimal point exists, thus affording flexibility in parameter selection (e.g., by increasing temperature, the necessary retention time and additive concentrations are decreased). The findings substantiate the feasibility of pyrohydrolysis roasting in reducing the chlorine and fluorine in the EAF dust to a level that will obviate industrial concerns about halogen contamination. The end-product of the pyrohydrolysis procedure is a de-halogenated, self-fluxing calcine which can be directly charged to a plasma or flame reactor. The paper includes design parameters and flow diagrams illustrating the pyrohydrolysis process integrated with the plasma and flame reactor technologies.

Jan 1, 1992

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By Leila Figueiredo de Miranda, Leonardo G. de Andrade e Silva, Anderson dos Santos Mesquita

ThisworkseekstounderstandifPETcompoundswithcarbonblackcan be uses to replace polypropylene and polystyrene for anti-static packaging mate- rials. PETcompoundswerefabricatedcontaining10.0;11.0;12.0and15.0weight % of carbon black with a particle size 325 mesh. We determined the thermome- chanical properties (Dynamic Mechanical Analysis—DMA, Tensile Properties, Fracture Toughness, and Hardness) and Electrical properties of the compounds. In conclusiontheresultsshowthecompoundbased onPETfilledwith 15.0% carbon black might be used in the handling, transportation and storage of electronic components because their mechanical properties, thermal and resistivity are satis- factory for this purpose. (cid:1) (cid:1)

Mar 1, 2018

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. n this work, the potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (OW). Seven taxa are of Alyssum genus and one of BornmueIIera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mg/kg or 2.5%) and Alyssum markgrafii O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By G. S. Victorovich

Technical progress in primary smelting has changed the face of the copper industry in the years since the Second World War. Much of this change has resulted from a wide acceptance of flash smelting technology. In addition, research has been directed toward devising converting processes to replace conventional Peirce-Smith converting technology. One major thrust has involved a revival of the old " ", idea of oxygen flash converting of comminuted mattes. This paper reviews the 60-year history of flash converting. Particular attention is paid to Inco's investigations into the processing of white metal containing significant amounts of nickel and, in some cases, iron. Thermodynamic analysis and laboratory experimental results are presented which throw light on the behaviour of nickel and other salient features of flash converting. The possible role of oxygen flash converting in the copper pyrometallurgy of the future is briefly discussed vis-a-vis direct production of copper.

Jan 1, 1993

By Rodney Hundermark, July Ndlovu, Lloyd Nelson, Phillimon Mukumbe, Paul van Manen, Whitey Seyanund, Bart Pieterse, Bertus de Villiers, Diale Mokwena

The 2003 redoubling in power to 68MW on the Polokwane Smelter furnace represented a significant intensification in platinum group metal (PGM) smelting. Combined with onerous ‘green’ PGM concentrate smelting requirements, this yielded conditions unusually corrosive to copper coolers and refractories. This presented unexpected operational and design challenges to reliable crucible operation and maintenance. Combined with specific operational control intervention, development of protective coatings has led to the life of water-cooled copper components improving from 9 to 40 months. The furnace matte endwall was extended in 2010 to address accelerated wear of refractories and the potential risk for contact of copper components by superheated matte. An 18 month planned endwall rebuild cycle has been demonstrated (versus catastrophic failure within 9 months). Finally, benefits including lower energy consumption, improved metal recoveries and higher productivity resulting from operational and in-house design developments will be described, that justify “Celebrating the Mega-scale” in PGM smelting.

Jan 1, 2014

By Jiann-Yang Hwang

Hydrogen storage is a critical issue for the hydrogen economy. Current storage technologies are not able to meet the combined gravimetric, volumetric, and system cost targets set by the Department of Energy. To solve the problem, the development of a new material - perhydride ? is proposed. Perhydrides are defined as materials that contain more hydrogen atoms in their molecules than conventional hydrides do based on the valence. This concept is supported by the versatile bonding capability of hydrogen and the recent discoveries in the chemistry of hydrogen clusters.

Jan 1, 2006

By Wei Lv, Gangqiang Fan, Xuewei Lv, Kai Tang, Yingyi Zhang

The EAF smelting process of ilmenite concentrate consumes large amounts of energy. Semi-melting reduction can lower the reaction temperature and separate the iron and slag more thoroughly. However, this needs additives and pre-oxidation to promote the reaction. In this paper, the pre-oxidized ilmenite powders were reduced isothermally with graphite and Na2SO4. The influence of reduction conditions on the metallization ratio of samples, such as reaction temperature, and sodium sulfate additive were investigated. The results show that additive such as Na2SO4 can significantly decrease the melting point of pre-oxidized ilmenite concentrate.

Mar 1, 2017

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

By Renato G. Bautista

"The development of processing methods for the preparation .of three electronic materials with rare-earth components is discussed. The resulting processing innovations are the results of a search for an economically competitive pilot scale or industrial production flowsheet without compromising the required properties of the final products. The three cases highlighted in this presentation are: 1) The preparation of high energy (Pr-Nd-Ce)FeB magnets for MRI application from a mixed-rare-earth oxide with a narrow range of composition directly prepared from the solvent extraction circuit of bastnaesite ore. 2) The kg production of the giant magnetocaloric effect Gds(SixGe1-x)4 magnetic refrigerant materials from commercial grade gadolinium metal (95 to 98 at. % pure) instead of high purity gadolinium metal (99.8 at. %); and 3). An industrial chemical synthesis flowsheet for the production of the superconductor precursor of YBa2Cu3O7.INTRODUCTIONIn the laboratory discovery stage, the synthesis of a new material is carried out using very high purity components, usually the highest purity available. As the new material is studied and characterized, the effectiveness of its desirable properties becomes better defined and understood. The evaluation of the effectiveness of the .property over the range of a given parameter and other interactions are further studied. Once it's potential application becomes clear, a practical and economical processing method need to be developed. The successful material processing flow sheet does not necessarily have to be a scale up of the laboratory procedure. At this stage, substitution of starting components and with lower purity materials is considered as the economics of the processing becomes a major issue. In addition, other approach to it's synthesis"

Jan 1, 2000

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Fujita, Kohei Mitsuhashi

An investigation on improving copper and iron recovery by removal of organic carbon and carbonaceous gangue mineral through flotation was carried out. The ore contains chalcopyrite and bornite as valuable minerals, and dolomite and calcite as carbonaceous gangue minerals. The chemical composition of the ore indicates that grade of 2.08 and 5.37 mass% for copper and iron respectively, while carbon was 3.70 mass%. The total organic carbon in the feed was recorded as 2.02 mass%. The presence of these gangue minerals is detrimental to copper and iron recovery during flotation. Therefore a two stage flotation study was carried out to remove hydrophobic carbon and carbonaceous material from ore and to improve copper and iron recovery. The objective of the study was to find effective and selective flotation conditions which can eliminate gangue minerals from valuable minerals and improve quality (grade) and recovery of copper and iron. The obtained results could be used to develop a flotation circuit for recovering copper and iron from carbonaceous sulphide ores.

Mar 1, 2018