Search Documents

By H. K. Lin

Thermodynamics of Cu-C1-H2O system and the kinetics of copper dissolution in cupric chloride solution were studied with emphasis on possible difficulties which may occur during copper electrowinning. E,-pC1 diagram of this system wasestablished. Equilibriumdistributionof various copper chloride complexes of different valent states at the presence of metallic copper was computed through the relations of the simultaneous equilibria. The mechanism-of copper dissolution in the cupric chloride solutions was proposed and the mechanism of copper electroposition was discussed. The researched results were used for guiding the investigation of copper electrowinning from cupric chloride solution.

Jan 1, 1991

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By Bin Xu, Qian Li, Xin Min, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The ringing characteristics of acid and alkaline iron ore pellets powder in kiln were studied by the thermodynamic calculation using software FactSage7.0, roasting experiments using briquetting method and analysis of SEM-EDS. The thermodynamic calculation demonstrated that liquid phase could be generated from alkaline pellets powder at a lower temperature and the amount of formed liquid phase was much more than that from acid pellets powder at the same temperature. Roasting experiments indicated that the compression strength of alkaline pellets powder briquettes were also higher than that of acid pellets powder briquettes. Additionally, the analysis of SEM-EDS suggested that the alkaline pellets powder briquette presented more liquid phase and a more compact structure comparing with the acid pellets powder briquette, which was consistent with the results of thermodynamic calculation and roasting experiments. Hence, in comparison with acid pellets powder, alkaline pellets powder is much easier to ring in the kiln.

Mar 1, 2017

By Y. F. Jia

Arsenic constitutes a major contaminant for the hydrometallurgical industry. Its removal and immobilization from process effluents typically involves lime neutralization and co-precipitation with ferric iron (Fe (III)/As(V)>3). Alternatively, precipitation of scorodite (FeAsO4?2H2O (cr)) may be applied to arsenic fixation. The mechanism of arsenic fixation in the former process has been suggested to be surface adsorption. Unequivocal characterization of these products is difficult because of their amorphous nature hence a variety of methods need to be applied including the particularly powerful method, extended x-ray absorption fine structure (EXAFS) spectroscopy. In this study, we have investigated the preparation of arsenate-adsorbed ferrihydrite with the purpose to compare its structure to that of Fe(III)-As(V) co-precipitates and scorodite (both amorphous and crystalline). Furthermore the solubilities of these Fe(III)-As(V) solids are measured as a function of pH. Their structures are elucidated and correlated to their solubilities and thereby the application of these findings to the practice of arsenic removal and disposal is assessed.

Jan 1, 2003

By Habib Saridikmen

In this experimental study the effects of slag composition on the phosphide capacities of the slag as well as on the phosphorus distribution ratios between the slag and metal phases encountered in ferromanganese smelting have been determined at 1500°C under carbon monoxide atmosphere. The distribution results were employed to calculate the phosphide capacities of the SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.metal phase. The classical gas-slag-metal equilibrium-quenching technique was employed using CO gas atmosphere and graphite crucibles to saturate the metal phase with respect to carbon. The phosphorus distribution ratio increased from 0.045 to 0.375 when the slag basicity increased from 0.72 to 1.39. As expected, the distribution ratio decreased from 0.375 to 0.105 when silica increased from 37 % to 45.8% in the slag phase. The phosphide capacity values were calculated by using the results of experiments. Empirical relationships were developed to express the phosphorus distribution ratios and phosphide capacities of the above slags.

Jan 1, 2006

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By G. Gomathi, K. Asokan, K. Subramanian

An electrochemical reactor with anode and cathode chambers separated by a composite perfluoro polymer cation exchange membrane was designed, fabricated and used for the reduction of dissolved carbon dioxide under ambient conditions to formate. The flow reactor enhanced the mass transfer of carbon dioxide compared to the batch reactor. Experiments were conducted using two different perfluoro polymer membranes - Nafion 961. Efficacy of CO2 reduction on various cathode materials (Cd, Pb, Sn and Zn plated stainless steel woven mesh) were determined. Optimum values of flow rate and current density were evaluated for the energy efficient formation of formate in aqueous KHCO3 (pH 7.5-8.5) buffer solutions.

Jan 1, 2008

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By Bhavani Kedika, Venkatagiri Noole, Krishna Thotla, Krishna Reddy Chepyala

Cationic lipids are attractive candidates for transgene delivery and expression and are safer alternatives to viral delivery vehicles. Here, we report the design, synthesis, characterization and transgene expression efficacies of a series of chrysin derived cationic lipids. A series of ten lipids of chrysin was synthesized by treating the 7-hydroxy group with dibromoalkane and further substitution of the bromo derivative with alkyl amines. The synthesized lipids were characterized spectroscopically. Parallel screening of the synthesized lipids for in vitro plasmid delivery expressing luciferase led to identification of several leads that demonstrated higher transgene expression when compared to the standard. Transgene expression efficacy was dependent on the chain length of the lipid. The influence of the various physicochemical properties on transgene expression efficacies was investigated. This study indicates that lipids derived from chrysin results in high levels of transgene expression and may be attractive for gene therapy applications.

Mar 1, 2017

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By Jorge D. Vier, Raúl B. Rebak, Alicia E. Ares, Natalia S. Zadorozne

Recent worldwide demand has driven nickel and molybdenum prices to record high values. Alloys containing significant amounts of nickel and molybde- num, such as the austenitic and duplex grades, have experienced significant price increases and some spot shortages have resulted in some regions. With low or no nickel content and reasonable molybdenum content, super-ferritic stainless steels are now proving to be the most cost effective corrosion resistant materials. The electrochemical behavior APMT® (Fe–21Cr–5Al–3Mo–0.04C) and 4C54® (Fe–26.5Cr–0.8Mn–0.5Si) super-ferritic stainless steel in NaCl solutions has been studied using open circuit potential measurements, potentiodynamic polarization curves, and electrochemical impedance spectroscopy. The aim is to compare the behavior of these materials with austenitic stainless steel alloy 316 (Fe–18Cr–10Ni– 2.5Mo). The results indicate that the APMT alloy presents a better performance than the AISI 316 stainless steel, while 4C54® does not, especially at anodic potentials. The good behavior of APMT® may be attributed to Al and Mo content in its composition.

Mar 1, 2017

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By D. R. Flynn

The recovery of nickel and cobalt from electromachining sludges in the form of relatively high-purity marketable products has been investigated. The investigation has shown that a series of metallurgical unit operations can be performed to recover nickel and cobalt from electromachining sludges in the form of al kal i nickel ic hydroxide and cobalt sulfate/cobal t metal, respectively. The recovery unit operations for nickel include high pH cyanide complexation, followed by oxidation and precipitation of alkali nickel hydroxide. The resultant filtrate can be treated for cobalt recovery by neutralization and acid baking to produce cobalt sulfate. The cobalt sulfate can then be treated for cobalt recovery by electrowinning. Results from laboratory bench scale test work are discussed in terms of appropriate operating conditions.

Jan 1, 1991

By Jinsheng Wang, Zhixiong You, Xuewei Lv, Yu Zhang, Jie Dang

Electro-titania slag is generally used as the raw material for titanium dioxide production by sulfate process. The phase composition of titanium as well as their disseminated grain size have significant effect on the acidolysis of titanium. Anosovite is considered as the most favorable Ti-bearing phase due to its high acidolysis ef ficiency, while silicates and rutile are not soluble in concentrated sulfuric acid. Different cooling rates will play a significant effect on the phase structure and particle size, which directly affects the acidolysis ratio of titania slag. In this paper, the influence on acidolysis ratio of titania slag at different cooling rates was studied. The results revealed that slower cooling rate resulted in the formation of larger particle size and a comparatively higher acidolysis ratio was obtained. On the contrast, rapid cooling was disadvantageous to the leaching of titanium as the smaller particle size anosovite was wrapped by glass phases.

Mar 1, 2018

By D. G. Schmidt

Tests were conducted on C86200 high-strength yellow brass in order to ascertain the effect of a low level of nickel on the mechanical properties on this alloy. A series of two alloys was studied, one of which had a nickel content of 0.85% and the other with <0.05% nickel. Copper and aluminum content ranged from 62.5% to 64% and 3.2% to 4.6%, respectively. When compared by zinc equivalents, a nickel addition of 0.75% in high-strength yellow brass does not act like copper but raises the tensile strength, 0.5% yield strength and BHN while lowering the elongation.

Jan 1, 1999

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012