Search Documents

By Baptiste Laubie

Agromining is a phytotechnology aiming at producing commercial metal compounds from low-grade ores thanks to hyperaccumulating plants. The fern Dichranopteris dichotoma is a rare earth element (REE) hyperaccumulator, which naturally grows on former mine tailings in China. It accumulates up to 0.35% of REEs in its aerial parts. Different hydrometallurgical processes are currently developed to recover these elements directly from the biomass or from ashes after combustion. The process presented here consists of a direct extraction by EDTA solution, followed by precipitation with acid oxalic. Optimal precipitation pH and influence of organic matter are determined by modelling and by experimental studies. The final solid contains 4.3% of REEs, with calcium as the main cationic impurity (0.45% of the precipitate). The recovery yield is similar for major REEs and is around 70%. After optimization, upscaling of the process will allow the agromining development to recover REEs from secondary resources with more environmentally friendly techniques.

By Torma A. E.

Biotechnological processes are considered to be cost effective especially for situations where the recovery of metals from 'Very large volumes containing trace metal concentrations (less than 10 ppm) is concerned. Microorganisms, alive or dead, or their products can be highly efficient and selective biosorbents for metal concentration. It is important that the metal bound to the biosorbent can be stripped by suitable agent(s) and regenerated for repeated use. The stripped solution should be concentrated enough to be introduced into the common metal recovery circuit. The industrial acceptance of biosorption processes is dictated by increased competitive advantage over other processes. This paper reviews the pertinent literature?, regroups the information, and points out future possibilities for the mineral and metal processing industries.

Jan 1, 1992

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001

By Rajashekhar Marti, York R. Smith

Lithium is anticipated to be a key, strategic material in the clean technology economy. The majority of lithium reserves are contained in continental brines and sea water (>60%). Currently the most economical approach to recover lithium from such resources is through selective adsorption. Spinel type lithium manganese oxide and lithium titanium oxide have demonstrated to be excellent candidate materials (after de-lithiation). However, due to the small size of the powders, they have limited industrial application and require immobilization. In this work, we examine the application of novel manganese oxide nanowire composites for the extraction of lithium from dilute solutions. Manganese oxide nanowires were synthesized and simultaneously immobilized on diatomaceous earth via hydrothermal method. Lithium manganese oxide were then formed by solid-state reaction, de-lithiated and tested for lithium ion adsorption.

Mar 1, 2018

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-SiO2 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [w(MgO)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, w(Fe)/w(Si02) is 1.1-1.4 and the temperatures are within 1473-1773K, the slag viscosities increased with the increase of W(MgO) and w(Fe)/w(SiO,). When w(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When w(MgO)>10%, the temperature should be kept above I 633K. When the content of MgO is higher, a lower viscosity slag can be produced by decreasing the ratio of w(Fe)/w(SiO,). The appropriate ratio of w(Fe)/w(SiO,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Preben Ingerslev

Control of the reheating of ingots is based either on surface temperature measurements using optical pyrometers or on furnace set points and reheat time determined empirically. This paper presents a real-time mathematical heat flow model, named BESTT, which calculates the temperature distribution in an ingot cross section when reheated or cooled. The model runs on a 486 PC in less than one minute for a variety of ingot cross sectional shapes such as circular, square and with some considerations octagonal and heavy-cornered square. Initial temperatures can either be uniform or nonuniform while accounting for temperature dependent thermophysical properties. The model was developed and verified using 718 alloy ingots in box type furnaces. When integrated with on-line pyrometric measurements, BESTT can provide for improved feed back in the reheating control loop. The use of BESlT will assist in reducing energy costs, and improving product quality and consistency. EPD Congress 1994 Edited by C. Warren The Minerals, Metals k Materials Sodety, 1993

Jan 1, 1994

By Haibin Wang, Kaile Tang, Chenn Q. Zhou, Guangwu Tang, Zhixiang Cui, Ping Zhou, Armin K. Silaen, Hongjie Yan, Zhi Wang

Bath smelting technology, such as the submerged lance smelting furnace, is used in the modern copper making industry. The first submerged lance smelting furnace developed by Dongying Fangyuan Nonferrous Metals Co., Ltd has shown potential for high productivity and energy savings. In this study, computational fluid dynamics (CFD) was applied to investigate the current design of the furnace. A three-dimensional multiphase CFD model was developed to study the interaction between injected gas and the liquid bath. The multiphase Eulerian model was used for simulating gas/liquid two-phase flow. The flow pattern in the submerged lance smelting furnace indicated rapid flow development and strong turbulent interactions between the gas and liquid phases. The model was validated based on a water model experiment of the mixing process. Mixing times from the simulation results show good agreement with experimental data. Additionally, based on this model, the gas residence time and liquid copper matte splashing phenomena under varying gas flow rates were investigated.

Mar 1, 2017

By Yan Wen

For the impurities in the copper smelting waste acid, SO3, Cu, As, Pb, Zn, Re and other elements enter the waste acid and generate a lot of arsenic residue, gypsum and neutralized residue, in which Cu, Zn and Re metals have not been recycled. Cu, Re and As are separated by step-wise vulcanization. The valuable metals of Cu, Zn and Re are recovered by separating zinc through pH adjustment. Calcium injection is conducted for boiler for reducing the amount of SO3. The residues generated in the form of arsenate and hydroxide will be returned together with arsenic filter cake for smelting treatment so as to achieve the purpose of valuable metal recycling and solid waste reduction and harmless treatment.

By André Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Mines Camchib Inc.. It is characterized by very fine first generation gold and very coarse second generation electrurn. Successful milling required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented. As a result of the circuit modifications, gold recovery increased from 65 to 81% in flotation and cyanidation. Overall gold recovery increased from 77% to 88-89%. These improvements are mostly attibutable to the recovery of -10 urn gold, whose presence in the Joe Mann ore and original circuit tails had been identified by process mineralogy.

Jan 1, 1989

By Peng Peng, Ouo Cheng, Guodong Lai, Lijuan Chu, Zebiao Zhang

"The pressure acid leaching residue of zinc concentrate contains a large quantity of sulfur. The present study attempts to leach sulfur using a mixture of ammonium sulfide and water solution at 25°C. Effects of three leaching variables: ammonium sulfide concentration, leaching time, liquid/solid ratio on the sulfur leaching rate were investigated. The process conditions were optimized using response surface methodology based on the central composite design. From the analysis of variance (ANOVA), the significant factors on response were identified. The optimum conditions for leaching elemental sulfur from pressure acid leaching residue of zinc concentrate were obtained using an ammonium sulfide concentration of 2.5 mol/L, leaching liquid-solid ratio of 6.5:1 and leaching time of 7 min. Under the optimum experimental conditions, a maximum of 98.50% of total sulfur was extracted. The experimental results obtained agreed satisfactorily with the model predictions, with a correlation coefficient (R2) of 0.99.IntroductionSulfur is widely used in agriculture, medicine, rubber, building materials, gunpowder, wine and sugar, and other fields [1]. Currently the world sulfur production is 40Mt, out of which more than 90% is recovered from industrial processes, and 10% is natural [2], This highlights the importance of sulfur recovery. As the pressure leaching technologies [3] continue to mature and are increasingly applied to refining, a large quantity of high-sulfur residue is produced [4-5]. It is desirable to recover sulfur from this residue, so that it is economically advantageous, and reduces environmental pollution [6]."

Jan 1, 2012

By Khalid Hattar, Alexander McGinnis, Buchheitm Thomas, Paul Kotula, Luke Brewer

"Understanding the effects of extensive radiation damage in structural metals provides necessary insight for predicting the performance of those metals considered for application in the extreme radiation environment. Predicting mechanical performance after long term radiation exposure is of great importance to extending the life of current nuclear reactors and for developing future materials for the next generation of reactors. A combination of finite element modeling, nanoindentation, and TEM characterization were used to rapidly determine the microstructure and mechanical properties influences of ion irradiation on a standard 3 l 6L stainless steel sample. The results of this study found that ion irradiation and small scale mechanical property testing can be used to characterize extensive levels of radiation damage structure, only when significant consideration is given to ion irradiation depth, surface roughness and polishing condition, the irradiation temperature, and many other experimental parameters.IntroductionFor either the success of next generation nuclear reactors or the extension of current nuclear reactors significantly beyond their designed lifetimes, research is needed into the degradation of the microstructure and mechanical properties governing the performance of the reactor alloys exposed to extreme environments. Although the exact dose and temperature of these nuclear reactor plans may vary, the cladding and other structural components will be exposed to greater dose and at elevated temperatures. To acco=odate these severe exposures, established cladding materials are being testing to longer exposure and new alloy compositions are being considered. [1-3] For neutron test facilities to reach 100 dpa level, exposure times often span several years, significantly limiting the down-select process of potential new materials for extreme radiation environments. Ion irradiation has been used as a technique to provide a look at the effect of irradiation damage on materials in a significantly shorter time frame. Previous work using proton irradiation provides a deep, broad, and relatively uniform defect profile compared to heavy ion irradiation; however, using this type of radiation still requires weeks to months to reach the 100 dpa level. [4] In this research, we investigated the feasibility of using heavy ion (nickel) irradiation and small scale mechanical testing to provide in a few days a first order screening technique for potential alloys that are being considered for advanced testing."

Jan 1, 2012

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By Mustapha A. Raji, Alafara A. Baba, Kuranga I. Ayinla, Misitura Lawal, Abdul G. F. Alabi, Aishat Y. Abdulkareem, Rafiu B. Bale, Folahan A. Adekola, Muhammed O. Muhammed

Increasing demands for pure wolframite ore in the form of ammonium paratungstate (APT), tungsten oxide cannot be over emphasized. Thus, treatment of a Nigerian wolframite ore containing admixtures of scheelite (CaWO4: 96-900-9631) and stolzite (PbWO4: 96-900-9813) by hydrometallurgical route was investigated in hydrochloric acid chelated with phosphoric acid to extract tungsten via solvent extraction. During leaching, parameters such as leachant concentration, chelate dosage and reaction temperature on ore dissolution were examined. At optimal conditions (1.5 mol/L HCl + 2.0 mol/L H3PO4 solution; 75 °C), 95.0% of the initial 10 g/L ore reacted within 120 min. The derived activation energy of 56.80 kJ/mol supported the proposed dissolution mechanism. The unreacted product analyzed by XRD was found to contain siliceous impurities. Tungsten recovery from leachate was carried out by solvent extraction with Aliquat 336 in kerosene. Pure tungsten was recovered as APT and beneficiated to produce high grade industrial tungsten oxide of industrial values.

Mar 1, 2018

By W. R. Opie

Fundamentals of blast furnace smelting of low grade copper and precious metal scrap and residues are reviewed with emphasis on emission control, by-products produced, slag cleaning for high recovery of metal values and the evolution of an off-gas system to eliminate hydrocarbons that result from decomposition of plastics in the blast furnace- charge. Problems with tin, antimony and nickel in the smelter-refining cycle are discussed.

Jan 1, 1985

By K. C. Chou

The surface effect is one of fundamental topics in physical chemistry that has been studied over decades. However, its effect has been neglected in metallurgy researches and industry applications in the past years. With the progress of science and technology in metallurgy, the consideration of surface effect to the metallurgical processes has been paid more and more attention. In this report, it is shown that, how this factor affects the physicochemical properties of metallurgical processes and how to derive some new and more correct theoretical formulae for its application. Besides, some new technique related to the application of this factor in the experiment has also been developed for both fundamental research and industry applications. It is hoped that these progresses will promote some new developments both in fundamental and industrial applications for metallurgy processes.

Mar 1, 2017

By Nickolas J. Themelis

The flash oxidation and smelting of mineral sulfides is a very prominent metallurgical achievement of the second part of this century. Its initial industrial implementation owes much to the work of Petri Bryk, in Finland, and Paul Queneau, in Canada. However, attempts to develop flash reduction pro- cesses, such as the reduction of iron oxide concentrates with hydrogen, have not yet been successful. The author, on the basis of experimental studies on both kinds of flash reaction systems, examines the respective rate controlling phenomena and the relative rates of flash oxidation and flash reduction.

Jan 1, 1993

By C. Hennesmann, D. Maijer, S. L. Cockcroft, P. Yo

"Die cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. As part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Auto Parts Toyota Incorporated, work has been underway to predict heat transport and porosity formation in die cast A356 wheels. The basic heat transfer equations have been solved using the commercial finite element package ABAQUS to which specialized routines have been added to predict porosity. Preliminary work on predicting porosity formation focused on using the Niyama parameter as a measure of the probability of porosity. The latest version of the model incorporates a new fundamentally based porosity criterion, which takes into account the effect of hydrogen concentration. The development of this model together with its application to a series of cylindrical test castings as well as a production cast wheel are presented.I. IntroductionDie cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. Microporosity, in particular, is a common defect that can adversely affect wheel quality. The mechanism of microporosity formation in aluminum alloys is complex owing to its dependence on the interaction of a number of phenomena occurring during solidification including the decrease in hydrogen solubility, the decrease in volume, the development of the solidification structure, and the increase in difficulty in interdendritic feeding [1]. As a result, the amount, size, and distribution of microporosity is affected by a large number of casting parameters including thermal variables, melt composition, grain structure, modification, and inclusion content, making optimization by trial-and-error methodologies difficult.The use of criteria functions, based on thermal conditions during casting, offers a relatively simple approach to predicting microporosity. In practical terms, they are useful because they provide a straightforward method of assessing the impact of varying casting parameters on porosity through various thermal parametersl21 such as thermal gradient, cooling rate, solidification time, and solidus velocity. Drawbacks of criteria functions include insensitivity to varying hydrogen concentration and the limitation to qualitative predictions. Consequently, in aluminum alloys, attempts have been made to develop models incorporating the effects of hydrogen gas and microstructure evolution. However, these types of models represent a significant increase in complexity and sacrifice the simplicity and ease of application of the thermally based criteria functions."

Jan 1, 2001

By G. Djambazov, D. Shevchenko, D. Burnard, V. Bojarevics, K. A. Pericleous, W. Griffiths

Contactless ultrasound treatment can be useful for high-temperature or reactive alloys in the liquid state, where contact with an immersed vibrating probe is undesirable. The alternating component of the Lorentz force can generate sound pressure levels leading to cavitation of gas bubbles in the melt, through acoustic resonance. Resonance is a function of the speed of sound in the liquid, the shape of the volume containing it and surrounding boundary conditions. Induction forces applied to a crucible lead to bulk stirring and in general deform the free surface, whose precise shape may influence the resonance conditions. This effect is investigated here b ymulti-physics computer modelling. Calculated results for aluminium melts are compared with experimental data and conclusions are drawn as to the sensitivity to process parameters and the reliability of this type of ultrasound metal processing.

Mar 1, 2017