Search Documents

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction, The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory-scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the determination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the determined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors determining the time of reduction.

Jan 1, 2003

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Chen Song

Keywords: Co3O4, Cobalt Compounds, Morphology, Urea, Homogeneous Precipitation Depending on experimental condition, precipitation from cobalt nitrate and chloride solution in the presence of urea yield dispersed cobalt compounds with different chemical compositions and morphologies. The effects of concentration of cobalt solution and urea, agitation, on precipitation morphology were investigated experimentally. Generally in closed systems the particles are identified as cobalt (II) basic carbonate with needle type shape. In open system, spherical and plate-like precipitations of cobalt (II) basic cyanate are formed. The chemical formula of cobalt compounds was confirmed. They are CoII,III(OH)0.83(CO3)0.49 Ay?0.14 H2O (in tightly-capped reactor: A stands for NO3?, Cl?; y[A]molecular weight < 12.9) and CoII,III(OH)0.83(NCO)XAy?0.14 H2O. (in open reactor A stands for: NO3?, Cl?; 42 x + y[A]molecular weight < 44.82). The main reason was that the primary particles had different chemical compositions for the effects of the different kinds of anions and stoichio-chemical compositions of the primary particles. The effect degree of the anions depended on the co-existing anion radius in the reaction solution. According DTA-TG analysis of the cobalt compounds, the latter particles transform to Co3O4 powders on calcining. The shape of the Co3O4 particle with porous character has inheritance with precipitation. In this paper, it concludes that the particle formed by the principle of nucleation-aggregation in aqueous solution. The process of aggregation has played an important role in formation of particles. During calcination, the aggregation would be destroyed partly.

Jan 1, 2005

By Juárez T. Julio Cesar, Mendez R. Eliecer, Reyes P. Martín, Flores G. Mizraim Uriel, Teja R. Aislinn Michelle, Hernández C. Leticia, Reyes D. Iván Alejandro

The present study shows the characterization of a zinc concentrate collected at Hidalgo, Mexico, in order to identify its mineralogical species and to propose a leaching methodology for silver recovery. The results obtained by X-Ray Diffraction (XRD) show Sphalerite (ZnS) as the mineralogical matrix and silver into the specie proustite (Ag3AsS3). The techniques of Scanning Electron Microscopy-Energy Dispersive Microanalysis (SEM-EDS) and Polarized Optical Microscopy (POM) identified the presence of sulfides of Fe, Cu, Pb and Zn, in addition to silicates and feldspar. The proposed dissolution method of Ag(I) was carried out with [S2O3 2−] = 0.5 M and [NaOH] = 0.1 M to regulate the medium at pH = 9 for 12 h at 298 K. Oxidation of the concentrate was favored by injection of O2 to a partial pressure of 1 atm. Monitoring of the reaction was carried out by reading the [Ag] and [As] by AAS.

Mar 1, 2017

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By Yoshio Nakano

Keywords: Tannin gel, Palladium, Separation, Redox We have developed the novel recovery system of palladium from wastes, which is simple and generates little secondary waste in comparison with the conventional recovery processes, using tannin gel particles synthesized from condensed-tannin molecules. Pd is adsorbed onto the tannin gel particles through inner-sphere redox reaction mechanism: two-electron transfer from tannin gel to Pd(II) species, accompanied by ligand exchange between chloropalladium(II) complexes and tannin molecules. In addition, we propose the separation system of Pd and Au from Pd-Au mixture, which is feasible due to the difference in oxidization and reduction potential between Pd and Au species: PdCl3(H2O)? and PdCl42? are less adsorbable than Pd species containing fewer Cl, such as PdCl2(H2O)2 and PdCl (H2O)3+, while such a distinct difference between Au species is not observed.

Jan 1, 2005

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By Cheng Fang, Zhou Lie-xing, Peng Jin-hui, Guo Sheng-hui

This article discusses the behavior of temperature and microwave thermo gravimetric analysis characteristic of ammonium paratungstate in a microwave field. Experimental results show that when 12g of material is place in a microwave with 900W of power, paratungstate’s temperature rises at 70°C/min. This results in paratungstate’s temperature being 980°C after 14 minutes. Compared with thermo gravimetric analysis characteristic, former two-step process of paratungstate microwave calcined completed ahead of schedule, after two-step process reaction is more intense,Paratungstate warming is more rapidly, the reaction time is much shorter; According to XRD and SEM, the product is high purity, the crystal particle size is uniform, and the grain size is fine.

Jan 1, 2015

By Sibin Zhang, Shengli Wu, Youhao Yin, Yuandong Pei, Zhixing Zhao, Jiangshan Shi, Zhengyun Fan

Spraying medium to achieve an energy-saving and emission reduction for iron ore sintering has been researched, such as spraying natural gas, coke oven gas, oxygen, sintering flue gas and gas from annular cooler. This paper focuses on effect of spraying steam on sintering surface on reduction of NOx and dioxin emissions in practical sintering production in Shougang Jingtang. It can be found that, with the increase of sintering bed spraying steam amount, NOx and dioxin of flue gas showed a decreasing trend. As spraying steam 1 t/h for 550 m2 sintering machine in Jingtang, NOx content decreases 2.6–9.5 mg/Nm3, and dioxin decreases 0.007–0.014 TEG ng/Nm3.

Mar 1, 2018

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By R. Boom, Y. V. Meteleva-Fischer, B. Kraaijveld, H. Kuntzel

"Segregation of impurities during refining of metallurgical grade silicon (MG-Si) is an option to produce solar grade silicon (SG-Si). Directional solidification is a last step in production of SG-Si effective for removal of metallic impurities. The possibility is investigated to use metallic impurities originally present in MG-Si for removing boron and phosphorus. MG-Si has been treated using two methods: 1) alloying with calcium and 2) refining with Na2O-CaO-SiO2 slag, both by controlled cooling. The microstructure of silicon and the impurities distribution have been studied before and after the treatments. Using EPMA phosphorus and boron have been detected in 1-2 wt% concentration range in several intermetallic compounds in grain boundaries after both treatments. This observation points to a different possible mechanism of silicon refining from boron and phosphorus. Controlled cooling improves migration of phosphorus and boron to the silicide phases in grain boundaries, which can be removed by acid leaching treatment.2. IntroductionStandards for silicon solar cells and growing demand on “green” energy require economical and efficient route to the production of solar grade silicon. Refining of cheap metallurgical grade silicon is one of the promising options, where application of existing metallurgical approaches can result in cost-efficient production on industrial scale. Focus in refining is on impurities, which are most difficult to remove: B, P, Al, Ti, due to their large segregation coefficient in silicon and low vapour pressure [1]. Moreover, more environmentally friendly technology in comparison to the traditional Siemens process [2] will be in accordance with societal needs. Based on properties of common impurities in metallurgical grade silicon, alloying refining and slag refining are suggested as competitive techniques having potential effect on removal of impurities harmful for conversion of solar energy [3, 4]. Alloying with Ca followed by acid leaching was found to be effective for removal of Fe and Ti from silicon [5] and to enhance also removal of boron [6] and phosphorus [7, 8]. In the work of Inoue et al. [8] drastically increasing removal of phosphorus from silicon has been observed with an increase of Ca content and a thermodynamics-based explanation was provided. Since phosphorus has been found to condense in the secondary precipitate mainly composed of CaSi2, it can be removed together with iron and titanium by consecutive acid leaching treatment. Slag refining is one of the metallurgical methods proposed to be effective for refining of metallurgical grade silicon from boron [9, 10]. Slags with additions of the following oxides to silica have shown positive effect on removal of boron: CaO [11-13], Na2O [11,14]. Mechanism of slag refining from boron is based on oxidation of boron followed by its incorporation in the slag network [9,11]; the same mechanism is suggested for refining from phosphorus taking into account that oxides of boron and phosphorus are known as network-formers [15]."

Jan 1, 2012

By Xue Ping

Sm2Fe17 alloy is an important precursor for the preparation of Sm2Fe17Nx magnet, which possesses a higher Curie temperature, larger anisotropy field, better resistance to oxidation and thermal stability. In this paper, the wet chemical co-precipitation was developed for synthesis of the Sm-Fe alloy oxide precursor. Based on the principles of simultaneous equilibrium and mass balance, a series of thermodynamic equilibrium equations of Sm(III)-Fe(II)-NH3-C2O4 2--H2O system at ambient temperature were deduced theoretically and the thermodynamic diagrams of lg[M2+]T (M=Sm, Fe) versus pH at different solution compositions were drawn. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH value, reactant concentration, reaction temperature and aging time, etc. It is found that by precise control of the process, the Sm-Fe alloy oxide precursor was synthesized with fine crystallization and special size &size distribution.

Jan 1, 2008

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By Mingming Zhang, Ramana G. Reddy

"Carbon dioxide (CO2) is one of the most common by-products produced during light metals production. It is considered to be the cause of greenhouse effects. Efficient reduction of CO2 can help minimize the rate of global warming and improving energy sufficiency. In this paper, a novel light metal production process was developed using ionic liquid electrolytes. This process has significant advantages compared to the traditional high temperature processes such as zero CO2 and CF4 emission, low energy consumption due to the low temperature operation and nonconsumable electrodes. Two types of anode materials (graphite, extruded carbon) were tested in electrolysis experiment. The results showed that both anode materials were stable (negligible weight loss). However, the extruded carbon was found to be superior to graphite in terms of current density and current efficiency. The calculated energy consumption for aluminum production was less than 10 kWh/kg at current densities up to 300 A/m2.IntroductionGlobal demand for ultra-light, ultra-strong, recyclable metals is growing as the world switches to low-emission vehicles, energy-saving devices and sustainable products. Aluminum demand is forecast to climb by 30 percent; magnesium demand by 200 percent, while for the emerging industrial light metal, titanium, the demand is expected to be at least double in the next decade. However smelting of light metals is the most energy intensive among all the steps of light metals production. For example, on an average it takes about 15.7 kWh of electricity to produce one kilogram of aluminum from alumina [1, 2, 3]. Advancements in energy efficiency have been steady, but slow, and most U.S. aluminum smelting production operates at 95% current efficiency. Besides high energy consumption, another major concern of the light metals smelting process is the emissions of greenhouse gases (GHG). Electrolysis green house gas emissions in the Hall-Héroult process can be split into three groups: 1) reduction reaction emissions, carbon dioxide (CO2) and carbon monoxide (CO); 2) process upset perfluorocarbons emissions; and 3) hydrogen fluoride (HF) formed from the moisture (H2O) present in the raw materials [2, 3]. Hydrogen fluoride gas can be captured and returned to the cells by the alumina dry scrubbing system used in modern facilities. A total of 5.31 kilograms of CO2 is generated from the reduction process for each kilogram of aluminum produced in the average U.S. primary facility. The perfluorocarbon emissions are related to the “anode effect.” If the concentration of alumina in the bath becomes too low, other reactions between the carbon anode and the bath occur and tetrafluoromethane (CF4) and hexafluoroethane (C2F6) are generated. These gases have high global warming potentials (GWP), which is a ratio developed to compare the ability of each greenhouse gas to trap heat in the atmosphere relative to carbon dioxide"

Jan 1, 2008

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By Stephen Northey, Nawshad Haque, Terry Norgate

"Life cycle assessment (LCA) is a recognized tool to evaluate various processing routes for metal production. Declining ore grades and higher specific energy requirements for primary metal production put greater emphasis on recycling. Greenhouse gas (GHG) emissions of steel and aluminium metal production were quantified with recycling scenarios using material recovery facility (MRF) data from the database of SimaPro LCA software. The GHG footprint of the MRF is relatively minor compared with that of associated transport during collection (i.e. 10 times more than MRF) of curbside recyclable material. Additionally, if the bulk recyclable material is sent overseas (i.e. Australia to China) from the MRF for further processing, the GHG footprint of shipping can significantly be larger compared with the sum of the collection and MRF (assuming electricity is from same source). Thus opportunities exist for reducing GHG emissions from secondary metal production if it is processed close to the MRF.IntroductionIt is a challenge to recycle metals significantly, although theoretically infinite recycling is possible due to their elemental nature. Leaks from the metal stocks in society occur through corrosion, wear and dispersive uses, or via land filling or similar activities that return metals to the earth. In order to provide a technically sound and transparent assessment of metal recycling, a methodology such as life cycle assessment (LCA) should be used. By taking a life cycle perspective, the beneficial recycling properties of metals can be evaluated in a manner that enables appropriate comparisons with other materials or product systems that do not have recycling loops. In practice, mixtures of primary and secondary metals are often used in new products, and also at the end-of-life various processing methods are used for recycling.The difficulty of introducing recycling into LCA is to set the right boundaries for the different flows ending in different product systems. It is a question of which observed material flow belongs to the first product system and which one to the second or subsequent systems. Recycling can be part of any product LCA. However, it is often a complex issue which requires specific considerations. As pointed out by Yellishetty et al. and Birat et al. [l, 2], LCA practitioners are left with much freedom in allocation of environmental burdens to account for recycling, thus making subjective judgments on recycling and allocation of credits to recycling. This often makes it difficult to compare the results of LCA studies conducted by two different practitioners even on the same processes. As LCA is often used to define policy in government, business and society circles, it should be based on a sound, objective and unbiased description of recycling."

Jan 1, 2014

By Vijaya Thangavelu

Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. High salinity of water supplies and soils in the vicinity of nickel laterite ore bodies is a major abiotic stress to fungi and represents a major challenge in the application of bioleaching process in-situ. Salinity exposes fungi cells to Na+ toxicity and osmotic stress. This study examined the salt tolerance development of Aspergillus foetidus based on gradual acclimatization of organism, its salt threshold and the salinity effect on its metabolism. The biological leaching of weathered saprolite ore with the resulting halotolerant organism under saline conditions was assessed. It was observed that salinity stress affected the organism?s growth and energy utilization

Jan 1, 2006

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985