Search Documents

By R. Menge, N. Basin, M. Sibony, J. Lecadet, S. Schmidt

In 1996, Metaleurop replaced its conventional sintering and blast furnace lead smelting activity in Nordenham, Germany by Sirosmelt/Ausmelt technology. Following some alterations to the process and the equipment, the bath smelting plant reached its design capacity for the treatment of lead concentrates, lead sulphate paste from spent batteries, secondaries and internal by-products. A reliable metallurgical process has been established, and thus higher process stability has been achieved, increasing simultaneously the refractory life. Nevertheless, improvements are needed to control the process with a better automation system and reliable expert-systems, because of the intensity of the smelting process. The introduction of the Sirosmelt process for the pyrometallurgical production of lead instead of the prior conventional process has also demonstrated the following advantages: reduced emissions of heavy metals and gaseous compounds, reduction of the specific energy consumption, minimization of residues and a reduction of staff and maintenance costs. The environmental performance of the plant meets the requirements of the German regulations.

Jan 1, 2000

By Allan MacRae

Freeport-McMoRan Inc. operates an ISASMELTTM furnace for the smelting of copper concentrate at the Miami Smelter in Claypool, Arizona. In May 2017, the furnace was restarted after incorporating newly designed copper cooling elements from just above the tap hole to the underside of the roof. The objective of the improved cooling design was to extend campaign life by eliminating existing failure mechanisms with the wall refractory. In addition to upgraded bathline coolers and complete coverage of the gas offtake transition, or ‘kettle’, with plate coolers, a novel arrangement of coolers was installed in the remaining freeboard area. The shell required significant cutting and re-stiffening, as well as extensive modification of the cooling water piping. Based on performance observed to date, it is expected that smelter throughput will be increased due to extended ISASMELTTM refractory campaign life.

By Yuan Zeping

The distributions of impurities in the copper melt, the slag and the gas phase in copper flash smelting process were under study in the Guixi smelter, particularly during operating conditions of high oxygen enrichment with production of high grade matte. Several methods for the removal of impurities such as As, Sb and Bi in the copper smelting process were developed and implemented at the Guixi smelter. This paper described the effects of high oxygen enrichment, elevated matte grade, high temperature and high production rate on the distribution of impurities, methods adopted at the smelter for the removal of impurities, and the associated benefits in the utilization of these removal techniques which include the mathematical model for material blending, high thermal intensity operation at the flash furnace, extended converter blowing, and injection of slag modifiers consisting of Na2CO3 and CaO powder mixture to the converters and anode furnaces.

Jan 1, 1999

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By F. Shen

Qualitative and quantitative results obtained during the physical modeling of the molten aluminum flow in a tundish using an aqueous system are presented. Surface tuft, free-surface powder and laser sheet visualization techniques were utilized for qualitative studies, whereas laser Doppler velocimetry was used to elucidate the 3-D flow regimes quantitatively. The results of the study are used for validation of the CFD codes, and to explore the effect of the alterations below the nozzle in order to: (1) decrease turbulence levels, and (2) collect the inclusions. Near the nozzle, the interaction of the impinging jet and the inclined walls gives rise to vortex structures. Downstream of the nozzle, two counter-rotating secondary cells diminish in strength. As flow turns through the bend, a separation region is created. The flow heading into the closed duct is seen to be nonsymmetric. A video tape highlighting the major findings is presented.

Jan 1, 1993

By Wen Liangying, Zou Chong, Tan Xiuqin, Bai Chenguang, Zhang Shengfu

"Eight typical metallurgical byproducts containing iron were selected based on the effect of the chemical composition, particle size, additives on the burnout degree of pulverized coal. Effect of three typical byproducts including fine iron ore, BOF dust and BOF sludge on combustion reactivity and combustion efficiency were investigated using TG-DSC method. The results indicated that the three additives have obvious catalytic effects on pulverized coal. By comparison, the relative active sequence of byproducts to the catalytic combustion can be described as follows: BOF dust>BOF sludge>fine iron ore. Moreover, adding BOF dust as component of additives also shows significant catalytic effects on combustion efficiency during rapid heating process.IntroductionChina is the largest producer in the world with an annual output reaching over 6 billion tons. Solid wastes arising from iron and steel making increases the environment pressure in recently years. For instance, annual output of dust during the production of iron and steel making in China reach up to 5 million tons, which is close to 8%~15% of the amount of steel [1]. Another characteristic of these byproducts is they are finer particle which are just harder to deal with. Since some of solid wastes, including dusts, scales, and sludge, usually contain high iron content, sintering plants have traditionally been used to recycle byproducts in integrated steel plants in China. However these byproducts also have noticeable effects on sinter quality, sinter strength and productivity and, therefore, waste recycling is limited depending on the analysis of the waste materials [2]. Another method which is pre-treatment of byproducts in pelletizing process, increases of energy consumption and production cost. In addition, metallurgical byproducts often contain heavy metals and alkalis. For these reasons, recycling rate of the byproducts in China is very low. Therefore, how to recycle the byproducts in iron and steel making process is an important subject."

Jan 1, 2012

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By Tracey Brommer, Britt Elin Gihleengen, Elsa Olivetti, Randolph Kirchain

"Increased demand resulting from the economic and environmental advantages of recycling secondary materials has constrained secondary material supply. As a result of constrained supply, the conventional strategy to maximize recycled content in an individual aluminum alloy must be expanded to maximizing total recycled content in a given production period. This work compares the performance over a two week period of an actual remelter for two strategies; a sequential charge-by-charge optimization framework and an integrated approach that explicitly incorporates the production schedule. Optimizing across the entire two week production is found to increase recycled content and minimize primary and alloying material additions. It is expected that as the scrap material market continues to be constrained by high demand, longer term batch planning strategies that can optimize material allocation will deliver improved performance.IntroductionIntensifying economic and environmental pressure to incorporate secondary aluminum into products is pushing remelters to explore additional strategies and tools to increase recycled content. Aluminum remelters are exploring alternative sources of secondary materials because of constrained secondary material supply and relatively high primary and secondary material cost [1]. Computational models, such as blending models are a tool that could help industrial remelters mitigate supply and cost challenges and thereby increase recycled content. In particular, computational tools can help manage the incorporation of new raw materials of variable quality. Blending models find many industrial applications and have been explored for over sixty years originating with the classic nut-mix problem dating back to 1950’s [2]. Blending models optimize the raw material input to make a desired product subject to a series of constraints such as product specifications and material availability. Deterministic and linear blending model formulations are presently implemented in some industrial aluminum remelters [3]. The primary reluctance of aluminum remelters against computational model implementation is the incapability of their blending models to reflect the intricacy of industrial remelting conditions [4]. For example, to reduce calculation time, industrial aluminum blending models usually optimize a batch plan for a single alloy and are not formulated to optimize several products simultaneously. Since such a model does not include knowledge of subsequent charges in the optimized batch plan, the resulting batch plans tend to deplete the “cleanest” secondary materials leaving the more uncertain and compositionally challenging materials for later charges. As a result, a remelter may override the calculated batch plan or leave certain scrap materials out of the material input to conserve these materials for alternative products scheduled for later production. This work explores an alternative aluminum charge planning tool that can optimize across an extended production schedule and compares it to a heuristic sequential optimization strategy reflecting an industrial remelter."

Jan 1, 2012

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By Luciano B. Oliveira, Angela O. Costa, Sergio N. Monteiro, Luis Guilherme C. Marques

"Biofuels are gaining a relevant role in today’s world not only as a solution for the decreasing petroleum reserves but mainly as a positive contribution to the efforts in global warming mitigation. In Brazil, since 1975, the replacement of gasoline by ethanol started a so-called PROALCHOOOL program, which is now being complemented with the replacement of petroleum diesel by biodiesel. This biodiesel program was officially created in 2005 with mandatory goals, supported by legislation, of 2% addition in 2008 and 5% addition in 2013 into all commercialized regular diesel. In this work, a critical analysis of the Brazilian biodiesel program is presented. The technical aspects related to the different raw materials, including wastes, available for biodiesel conversion as well as the economical conditions associated with production costs and market logistic are discussed. The environmental benefits associated with the retention of greenhouse gases are also discussed.IntroductionToday the commonly accepted fact that the petroleum world reserves are probably passing through a maximum and start declining in terms of the total amount that can be extracted by existing technologies is motivating significant changes in our society. The continuous increase in the price of gasoline and other liquid fuels is an immediate worrisome and visible consequence. However, more than an economical problem, our civilization is already facing the effects of global warming, due to CO2 emission from burning fossil fuels, mainly from coal and petroleum. It is now realized that a large scale solution for these problems demands the prompt substitution of non-renewable fossil fuels by others that, in addition of being renewable, have a relatively lower contribution to the greenhouse gases."

Jan 1, 2008

By V. Reiter, K. Reinharter, C. Wenzl, D. Gregurek, A. Spanring

The refractory linings in lead furnaces are exposed to several stresses rather complex in their interaction. In the present study the magnesia-chromite brick out of a lead recycling furnace suffered from a high chemical attack by the process slag. The high CaO, BaO and sulfur bearing silicate slag, as well as a high NaO2 supply from soda resulted both in a deep-reaching infiltration of the brick microstructure and a severe corrosion of the brick components. Both the sintered magnesia and chromite were attacked chemically. The FactSage calculations showed the formation of high amounts of liquid phase in the infiltrated microstructure. Further phenomena affecting the refractory performance such as iron oxide attack, redox effects, and boron attack are also discussed in the paper. The obtained information and insights serve as a basis for improving refractory materials (i.e., choice of refractories for individual process and new developments) and consequently furnace operations.

Mar 1, 2017

By Xia Zhao, Yong Zhao, Wen Pan, Ze-jun Ma, Yan-juan Yang

Characteristics of the gas-solid reduction reaction between iron ore sinter and carbon monoxide (CO) gas at 1273 K were studied with thermogravimetric analyzer. The microstructure, mineral compositions and porosity of sample were investigated prior to reduction, in the 30% reduced sample, in the 70% reduced sample, and in the fully reduced sample. At the reduction degree of 30%, the hematite and calcium ferrite was reduced to 44.4 and 60.4% respectively. At the reduction degree of 70%, all the hematite, calcium ferrite and magnetite were reduced to metal iron, only 36% wustite was left in the core area. The reduction reaction began with the loose structures and spread to the nearby area. In the area of micropores, the reducing gas can easily diffuse to the reaction interface to proceed the reduction reaction effectively. So increasing the content of micro-pores is an effective way to improve the reducibility of the sinter.

Mar 1, 2018

By M. R. Barkhudarov

Semi-solid metal can be formed into useful products of near net shape and high quality. Use of this method has been limited, however, because of the difficulty of working with metal in the semi-solid state, which has strong shear rate, temperature and time-dependent properties. In this paper we describe a thixotropic model and apply it to the problem of small metal droplets impacting on a flat plate.

Jan 1, 1997

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By A. Siegmund, R. D. Prengaman

Lead anodes used in zinc electrowinning generally contain 0.5 - 1.0 % silver to reduce the rate of corrosion over the service life. For good quality zinc, the cathodes must contain less than 10 ppm lead. In order to reduce the lead contamination of the cathode, the lead anode must become coated with a protective layer of Pb02/Mn02. The formation of this layer may take as long as 30 - 60 days, during which time zinc production is substantially reduced and the cathodes are contaminated with lead. To improve the mechanical properties of Pb-Ag-anodes alloying elements such as calcium, strontium, barium and others are added. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate localized internal corrosion. Based on the experience as the major supplier of rolled anodes for copper electrowinning, RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb- Ag-Ca-alloy with a controlled surface grain structure. It forms an adherent protective oxide coating within 2 - 3 days when placed in an electrowinning cell. The preferred calcium and silver contents of the alloy are 0.03 - 0.08 % and 0.3 - 0.4%, respectively. Rolling sheets significantly reduces the presence of internal porosity or laps. The lack of defects results in long anode life. The rolling also produces a uniform grain structure to which the corrosion product readily adheres, thus significantly reducing the conditioning period.

Jan 1, 2000

By Y. Mori, K. Kawanaka

The permeability changes during the sintering of the feed for the Imperial Smelting Process (ISP) were investigated using an experimental sintering pot, as well as with a mathematical model. The results obtained were as follows. The blowing resistance in the sintering bed changes as the sintering reaction proceeds. It increases at the beginning of the reaction when the temperature of the bed is still low. Then it decreases as the reaction continues, accompanied by an increase of the bed temperature. The increase of the blowing resistance in the bed during the sintering process mainly occurred in the drying zone, and was comparatively small in the reaction and cooling zones. Based on Erugen's equation, the change of the permeability during sintering is explained by the decrease of the apparent fractional void volume in the drying zone of the bed.

Jan 1, 2000

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By Ming Li, Li Ma, Yunqing Tian, Haoyu Cai, Luyao Zhao, Wenwang Liu, Wenbin Huang, Gele Qing, Yan Zhang

In this paper, study on the in fluences of different Ti-bearing materials on MgO-bearing pellets metallurgical properties was carried out. The results show that, pellets compression strength will decrease while using ilmenite. However, TiO2 reagents help to improve pellets compression strength. The reduction swelling decreases while using TiO2 reagents, but different ilmenites have diverse impacts on the reduction swelling. Pellets compression strength will decrease and reduction swelling will be improved while adding magnesium additives. In order to produce qualified Magnesium-Titanium bearing pellets, the firing temperature should be no less than 1270 °C.

Mar 1, 2018

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000

By Chris P. Pistorius

Over the past few decades the carbon intensity of ironmaking and steelmaking has been reduced considerably through improved efficiency in blast furnace ironmaking, partial replacement of coke with less carbon-intensive fuels, and increased use of scrap and direct-reduced iron in steelmaking. To evaluate possible further reductions in carbon intensity accurate process information is needed. A preliminary test of the fidelity of publicly reported data as a source of process information is reported here. The sources are industry roundups of electric furnace furnace steelmaking and blast furnace ironmaking (published by the Association for Iron and Steelmaking Technology), and data recorded by the Environmental Protection Agency under the US Greenhouse Gas Reporting Program. From a comparison for an integrated steelmaking plant and an electric furnace furnace plant, it appears that the values from the two data sources are consistent. The comparison does rely on process details such as the quantitative relationship between injected oxygen and carbon emissions in electric furnace steelmaking.