Search Documents

By R. G. Robins

Metal separations based on the selective precipitation of phosphates have a potential application in many hydrometallurgical processes. This paper reviews the literature on the solubility of a number of both divalent and trivalent metal phosphates and presents the result of some additional experimental measurements. The systems examined have been modelled to obtain free energy of formation data for the various species. Computer generated solubility diagrams which are described can be useful in predicting a variety of metal separations.

Jan 1, 1991

By Erich Hovestädt, Hans-Jürgen Odenthal, Christian Wuppermann, Herbert Pfeifer, Antje Rückert

"During the argon oxygen decarburization (AOD) process high-chromium steel melts are decarburized by oxygen and inert gas injection through sidewall nozzles and a top-lance. Due to the large amount of the injected processing gas, low frequency oscillations of the vessel can be observed. It is suspected that these oscillations can influence the converter's structure. The exchange of forces between fluid and the surrounding vessel is the focus of this study. An oscillation model was developed and tested, one objective being to limit the computational effort which is necessary for fully coupled and time resolved CFD and FEM simulations. Experimental results obtained from water-model studies as well as from on-sight measurements are available and were used in order to validate the numerical results. The authors' intention is a contribution towards a more in depth understanding of the factors influencing vessel vibration during the AOD process.IntroductionDuring the last four decades the AOD process has been established as a reliable and efficient refining process in stainless steel making. The injection of process gases (O2, N2, Ar) through sidewall nozzles shows advantages in mixing effectiveness compared to other injection geometries e.g. bottom blowing [1]. Stainless steel grades contain usually more than 10% chromium. With decreasing carbon content during the decarburization periods the tendency of chromium oxidation increases according to the varying chemical equilibrium which depends on the partial pressure of carbon-monoxide (CO) in the gas phase. That's why oxygen is gradually replaced by inert gases, usually argon or nitrogen, in order to lower the CO partial pressure and thus to minimize chromium oxidation. Despite the high injection velocity of approximately Ma = 1, the kinetic energy of the gas jets is consumed within a short distance from the nozzle exits due to the large density ratio between gas and melt of approximately 1:8000. With increasing distance to the nozzle exit, the initial horizontal velocity of the gas jet decreases and due to buoyancy force motion of the detached bubbles turns into a vertical direction. Subsequently a gas plume develops with its typical conical shape described by various authors [1-4]. Due to the drag force between gas bubbles and melt also the liquid phase is forced into a vertical motion. Near the free surface and the wall regions the melt flow is deflected in different directions. Subsequently, the typical flow pattern in the AOD vessel arises, as sketched in Figure 1 and described in literature [5-9]."

Jan 1, 2012

By Truan-Sheng Lui, Li-Hui Chen, Fei-Yi Hung, Cheng-Yi Chen

"This research used the austempering heat treatment on the SCM435 thin specimen with a type of double loop and obtained the Cr-Mo bainite structure, and then we could further investigate the mechanical properties of SCM435 bainite structure. Experimental data showed the stability of the mechanical properties of specimen with austempering temperature 830°C for 25 minutes was better than that of 15 minutes. The size of austenite grain affected the strength of thin specimen. After austempering at 830°C-25minutes and salt bath at 290°C, the stability of UTS was better than that of salt bath at 310°C and 330°C. The average hardness of all specimens was about more than HRA70. The specimen with austempering at 830°C-25minutes and salt bath at 290°C-30minutes had bigger grain size of austenite and retained y, it also had higher hardness and strength toughness. So, its stability was improved for tensile strength comparing with traditional tempered martensite process.IntroductionSCM435 is a Cr-Mo steel with high strength and high hardness properties, and it has been widely used in machine parts, shafts, gears and strength screw products [1-3]. However, this system often has lower reliability due to the brittleness of high-temperature tempering and quenching inequality. Considering the austempering heat treatment can obtain the uniform bainite structure to improve the temper brittleness, and the austempering heat treatment is a continuous process that it also has efficiency and uniformity. For the thin plate specimens, the mechanical properties of the bainite structure are better than traditional martempering structures."

Jan 1, 2013

By Wantae Kim, Furnia Saito, Qiwu Zhang

"A novel mechanochemical processing technique for the preparation of zeolites from kaolinite in NaOH solution was investigated. Dry and wet mechanochemical treatments combined by subsequent moderate heat treatment could accelerate the synthetic reaction for zeolites from kaolinite. This stimulating process produced zeolite-A and zeolite-X from activated kaolinite at extremely lower reaction temperature than conventionally applied for zeolites production. Conversion to zeolite-A and zeolite-X was strongly dependent on the activated state of kaolinite. Wet mechanochemical treatment modified the chemical composition of activated solids. Rapid dissolution of AIO species rather than SiO ones in the reactant solution was accelerated by wet milling together with NaOH that promoted the formation of zeolite-X of high specific surface area.IntroductionZeolites are a family of hydrated alumina-silicate minerals contains alkali and alkaline earth metals. They have a framework structure that encloses inter-connected cavities occupied by large metal cations and water molecules. Zeolites are characterized for their ability toward ion exchange and reversible dehydration. Properties of them are exploited through commercial productions of particular structural and chemical features. Zeolites are used as commercial uses for catalysis for FCC (fluidized catalytic cracking) of petroleum refining, drying reagents of gases and liquids, and selective adsorbent for pollution control [1-3]. In such purposes, artificially synthesized zeolites are employed, although natural ones are associated with hydrothermal and hot spring alteration of volcanic materials. Commercially, a hydrothermal process has been used for the preparation of zeolite synthesis. This preparation method gives zeolites of high chemical homogeneity and purity, however, this wet-chemistry-based processing is significantly influenced by reaction temperature, pH, concentration, and composition of starting substances [4]."

Jan 1, 2000

By A. V. Tarasov

The proposed process is based on creating a controlled frothed layer of molten slag, in which fine particles of carbonaceous reductant and raw material to be processed are mixed with emulsified iron. Frothing of the slag layer without external blowing occurs as a result of intensive evolution of gaseous reduction products. The froth reaction process is maintained due to the heat of an electric arc in the slag layer. When the metal bath is heated by the arc to 1400- 1 500°C, the low temperature of the slag surface of about 1200-1 300°C is maintained due to low thermal conductivity of slag froth preventing heat loss. In order to maintain the required slag froth level and control the process temperature, air tuyeres are installed above the slag bath; blowing air serves also for oxidation of zinc in fumes and for its transportation. High adsorption and thermal insulating properties of slag froth ensure virtually complete elimination of dust and mist entrainment along with low heat losses. The main macrokinetic regularities of the carbon thermal reduction of zinc-containing slag melts have been studied under frothing conditions. The mechanism of formation of gas-slag emulsion has been identified under the conditions of reaction [C]+[O]=CO occurring locally at the slag-metal interface. It has been demonstrated that under the froth reduction conditions the zinc removal rate from the melt increases on the average by 3 to 5 times. Based on the physical and chemical data obtained, basic principles of the dezincing technology have been developed for different intermediate oxide iron-containing products produced in the process of ferrous and non-ferrous metals production.

Jan 1, 2002

By Ulrich E. Klotz, Gemot Pottlacher, Shahid Mehmood

"Platinum alloys are frequently used in technical applications and in jewellery. Their thermophysical properties such as density, heat capacity, thermal conductivity and surface tension play an important role in casting processes and are required as input data for casting simulation. Scope of this work was to investigate these properties by different methods. Platinum and four alloys namely, Pt96Cu4, Pt68Cu32, Pt50Cu50 and Pt25Cu75 were investigated. Melting range and thermal expansion was measured at fem by DSC and dilatometry, respectively.At TU Graz wire shaped samples were investigated by an ohmic pulse heating technique. This technique allows the calculation of specific heat capacity and the temperature dependencies of electrical resistivity, enthalpy, and density of these alloys in the solid and liquid phase. Experimental results were compared with available literature and data from thermodynamic calculation using the SNOBl database and ThermoCalc.IntroductionPlatinum is a precious element and its alloys are commonly used in jewellery. But Platinum is much more difficult to cast then other jewellery elements like silver or gold, because of its high melting temperature, large shrinkage during freezing, low thermal conductivity, high surface tension, and high viscosity. As a result there arise problems during casting. Hence to resolve these difficulties a detailed study of thermophysical properties of solid and liquid platinum and its alloys is necessary for simulation and casting. The Platinum alloy samples were prepared by vacuum induction melting and casting into copper molds. Rods of 3 mm in diameter and a length of 80 mm were prepared and drawn to wires of 0.5 mm in diameter."

Jan 1, 2011

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

By Hang Goo Kim

A mathematical analysis based on equilibrium modeling has been developed to describe the distribution behavior of minor elements such as Pb, Zn, Bi, Sb, and As among gas, slag and recovered copper phases during the reduction of copper oxide in slag cleaning with CO gas. The results show that large fractions of the impurities transferred to slag during smelting or converting are recycled to the recovered copper metal. It is also shown that there is a limit to the recovery of copper from slag because iron oxides are also reduced to form a copper-iron alloy at low oxygen potentials. The effects of various operating parameters such as temperature, the activity of FeO, the initial amounts of the elements in the slag and CO content in process gas, on the behavior of these minor elements are discussed. The predicted results were compared with the results of a pilot plant operation in which pulverized coal was used as a reductant. Consistent trends between the two cases were obtained.

Jan 1, 1992

By Yasuo Kudo, Wu, Hayato Sato, Hiroshi Nakazawa, Shouming

"In order to recover copper from a waste nickel condenser powder, bioleaching experiments were carried out using Thiobacillus ferrooxidans in a shaking flask. The content of nickel and copper in the waste nickel condenser powder in this study were 8.0% and 3.5%. X ray analysis showed the peak of barium titanate. In the preliminary study using metal nickel and copper powders , the dissolutions of nickel and especially copper were accelerated with the addition of ferric iron in the bioleaching of nickel and copper powders while not in the absence of ferric iron. Ferric iron oxidizes both metals, and Thiobacillusferrooxidans oxidizes ferrous iron resulting from the oxidation of metals, whereby the dissolutions of metals proceeds. The dissolution rates of nickel and copper increased with increase in the concentration of ferric iron in the bioleaching of the waste nickel condenser powder.1. IntroductionNickel condensers rejected from manufacturing plants are crushed and landfilled. Waste nickel condensers contain nickel and copper and could be considered as nickel and copper ores. Since the capacity of landfills is diminishing, it is required to recycle metals of waste nickel condensers in order to reduce the amount of wastes landfilled. Conventionally, metals in the waste were recovered by dry metallurgy after the incineration.Nickel has been refined by solvent extraction - electrowinning method (SX-EW method). Recently the amount of copper refined by SX-EW method has increased (Takahashi, et al. 1994). This method is cleaner and consumes less energy than conventional methods. Nickel dissolved well in acid solutions, but copper is not. If copper is leached efficiently from a waste nickel condenser powder, SX-EW method will be applied to recover copper from them"

Jan 1, 2000

By A. Dell’Era, M. Pasquali, C. Lupi

"An electrochemical cell has been designed to treat very diluted cobalt solutions, i.e. those deriving from recycling processes of lithium-ion batteries. A reticulated vitreous carbon sponge was used as cathode and a Pt-coated Ti net as anode. A controlled potential electrolysis has been carried out in a solution flowing in the cell and maintained at a constant pH of 6.5. Considering the cathode dimensions (10.0 cm * 10.0 cm * 1.25 cm), rather high volumes of solution (>1 litre) can be treated with flow rates up to 1.6 l/min. The process yield is obviously related to the solution concentration; it has been observed that, starting with a solution containing 200 ppm of Co2+, the yield is initially ~35-40%, but it decreases to ~20% when 80% of the initial cobalt content has been electrowon. The yield increases up to ~50% if the carbon electrode is coated by cobalt. The conditions allowing a fast and complete removal of cobalt are outlined. Introduction Industrial liquid effluents containing heavy metal ions arise not only during hydrometallurgical processing, but also in many sector of chemical industries utilizing metal catalysts and process reagents. These waste solutions containing low quantities of metallic ions can be treated by chemical precipitation, solvent extraction, ion exchange, etc. before final discharge. All these techniques could be efficient for complying the aqueous effluents with the severe rules related to the environmental impact, but they can not directly produce metals. Particularly the chemical precipitation presents two main drawbacks, huge amount of sludge prodction and reagent costs to produce this useless and sometime dangerous sludge that have to be considered. Electrochemical technologies can be used for the treatment of effluents polluted by metal ions, showing the following advantages in comparison with other processes: 1. recovering of the polluting substances in metallic forms, with subsequent reusing; 2. absence of process slag, which should be subsequently disposed of. In this work an electrochemical reactor with a reticulated vitreous carbon cathode and a platinated titanium net anode has been designed and utilized for removal Co from waste aqueous solutions. Porous materials have been used as electrodes for this cell, as their high specific surface area favours the treatment of these low metal content solutions (1-7). This kind of electrodic material presents very interesting chemical-physical characteristics such as: low density, low thermal expansion and high electrical and thermal conductivities; particularly the reticulated vitreous carbon (RVC) presents a very elevated void volume, rigid structure, good resistance to temperatures in non-oxidizing environments and very low resistance to fluid flow."

Jan 1, 2008

By J. H. Huang

In this investigation, the selective precipitation of cobalt and molybdenum from Co-Mo aqueous solutions was studied in order to recover efficiently valuable elements from industrial effluents generated from a novel electrodeposition of nanocrystalline Co-based alloys process and reduce the effluent impact on environment. It was found that the behavior of cobalt in aqueous solutions was substantially affected by the presence of molybdenum. When adding 11.6 to 46.6g/L molybdenum to a 50g/L cobalt solution, the co-precipitation of molybdenum and cobalt started to occur at pH value of 3-4. However, without the presence of molybdenum, cobalt could only be precipitated out of the solution at about pH 6. Most of the molybdenum was found in the solid phase when the solution pH reached 5. After further increasing pH to greater than 7, the molybdenum dissolved back into the solution. Cobalt kept precipitating as the pH increased. When the pH was greater than 7, most of the cobalt was present in the solid phase. The chemical and physical characteristics of the precipitated materials were investigated by SEM, XRD, AAS and EDX. It was revealed that the precipitate was initially present as cobalt molybdate oxide hydrate and subsequently transformed as sodium cobalt molybdenum oxide. With further increasing the solution pH, the precipitate was transformed into cobalt hydroxide. Further investigation implied that most of molybdenum was chemically tied to the precipitate produced at the low pH, yet at the same time, physically entrapped at the high pH. The paper also presents the influence of reaction temperature and time on the precipitation process and kinetics.

Jan 1, 2003

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Yosry Attia

Recent emphasis on environmental effects and costs of conventional mining processing, plus success in accelerating bacterial action, suggest that biotechnology be explored for gold ore processing. In our paper, the past experience with organisms in processing gold is reviewed. The use of microorganisms for liberation of gold from sulfide ores as a substitute for fine grinding is discussed. The possibility of accumulation of gold from solutions, such as cyanide solutions, is explored as a potential replacement for such processes, such as carbon-in-pulp or ion exchange. The improvement in engineering technology and kinetics needed to scale-up from laboratory experiments to production scale are outlined.

Jan 1, 1985

By John M. Gaines

Lead concentrates from the Viburnum Trend in Southeast Missouri are sintered, prior to smelting, to bind the particles together, homogenize the feed, and reduce the sulfur content. About 20% of the sinter at some plants is classified as bad sinter. A total of 130 samples of good and bad sinters were studied by reflected light microscopy, scanning electron microscopy-energy dispersive analysis, and electron microprobe analysis to characterize their differences in mineralogy and textures. Good sinters consist predominantly of hardysonite, franklinite, lead silicate matrix, and large crystals of calcium-magnesium-iron silicate, together with minor amounts of lead oxides, lead-zinc silicate, metallic lead, specular hematite, magnetite, lead-iron-bearing zincite, and zinc-lead-magnesium-bearing wustite in a tightly intergrown mesh of crystals and with an evenly distributed porosity of about 15-20%. Bad sinters contain larger amounts of lead silicate matrix, galena, metallic lead, and lead oxides, but smaller amounts of hardysonite, franklinite, and calcium-magnesium-iron silicate, lack intimate intergrowth of the phases, and have lower (0-5%) and unevenly distributed porosity.

Jan 1, 1992

By Rolando Campos

The CODELCO-CHILE Teniente Converter Technology, is presently being applied in four Chilean smelters (Caletones, Chuquicamata, Potrerillos and ENAMI-Ventanas). A Teniente Converter is due to be used at ENAMI-Hernan Videla Lira (Paipote) smelter in the near future. Also, a Teniente Converter is to be installed as part of a retrofit project for Nkana smelter of Zambia Consolidated Copper Mines Ltd. (ZCCM). The charge to be treated through this smelter will consist of a blend of concentrate arisings from the various concentrators within the ZCCM group. The present status on the application of the Teniente Converter Technology at Caletones smelter as well as its projected performance when used at Nkana smelter, are presented in this paper. The design operational basis, autogenous smelting throughputs, concentrate to matte ratios and benefits due to the use of technical oxygen, are presented and analysed.

Jan 1, 1992

By T. Shibaraki

A new larger, more efficient and economical Mitsubishi furnace line at Naoshima was put into operation in May 1991. Naoshima Smelter had produced previously about 230,000 mtpy anode copper with two smelter lines, i.e., a conventional reverberatory furnace line and Mitsubishi furnace line, which had been shutdown at the same time of the start up of the new smelter. At the beginning of the operation, there were several initial problems at the area of off gas trains and feeding system. By overcoming them now the process has been continuing satisfactory operation at the design rate. The paper describes about the design concepts and the actual operation of the new smelter.

Jan 1, 1993

By L. A. Mills

After three years of experience in operating the pilot plant for the Noranda Continuous Smelting Process, the decision was made, in March 1971, to build an 800 ton per day commercial plant at Noranda, Quebec. The de- sign and layout of the plant is discussed and the installed equipment described. Experience previously gained in the pilot plant is mentioned when it has been used in the choice of equipment or plant layout. The full- scale reactor was started up in March 1973 and the operational datacollected and the experience acquired during the first 30 months of operation are described. This includes operation to produce both high grade matte and copper. Areas discussed include refractory wear, fuel consumption and throughput of copper concentrates. Changes made to original equipment and methods of operation are discussed, together with the reasons. The ad- vantages of using solid fuels to handle inert materials and to maximize converting air flowrates and concentrate throughputs are described. Relative efficiencies of oil and natural gas are compared. The addition of oxygen from a 94 ton per day oxygen plant to the reactor converting air was started in August 1975 and the initial operating results are included.

Jan 1, 1976

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By Zhou Jiemin

In order to fully understand the behavior of the rectangular six- electrode electric smelting furnace and improve its design and operation, a three-dimensional mathematical model has been developed which incorporates the electrical and thermal flows into numerical solutions, assuming a steady state regime. The model has been used to simulate the performance of the 16500 kVA nickel matte smelter at Jinchuan in China, and various factors have been investigated. The results of computation are in agreement with the measured data obtained from this furnace and its physical model. Application of this model is described and the calculation on the Jinchuan smelter shows that the operation expenses can be reduced by optimizing the furnace geometry and some operating parameters.

Jan 1, 1991

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988