Search Documents

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By K. Gao, R. Dry

"Carbon boil, which results in excessive spitting and even complete destruction of a metal drop, could significantly influence the efficiency of direct smelting processes. Carbon boil has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure, and melt area/volume ratio. The time of carbon boil was determined using a CCO camera coupled with a time/date generator connected in parallel to a video recorder and a computer. The time of carbon boil was in the range ~5 - 15 seconds under the conditions in this study. A mechanism for carbon boil has been proposed.IntroductionThe occurrence of carbon boil in molten iron drops can result in excessive spitting and sometimes even complete destruction of a metal drop. In direct iron smelting processes, this could significantly influence the decarburisation of liquid metal and the post combustion and hence may influence the efficiency of smelting processes. The generation and consequent ejection of metal droplets into the gas phase occurs due to the intense turbulence in the bath which results from the injection of gases and coal. The aim of this investigation is to understand the fundamentals governing the carbon boil phenomenon under direct iron smelting conditions to assist control of process efficiency.Carbon boil phenomenon has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure and melt area/volume ratio. The time for the occurrence of carbon boil has been determined in this study at 1440 °C using a novel approach which includes utilisation of a CCD camera coupled with a time/date generator connected in parallel to a video recorder and a computer. This arrangement permits the capture of the entire sequence of events leading up to carbon boil and therefore the determination of time of boil which is in the range -5 - 15 seconds under the conditions in this study."

Jan 1, 1996

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of' ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999

By J. L. Holman

The Bureau of Mines is investigating recovery of Ni, Co, Cr, and other metals from mixed contaminated supera110y scrap. The scrap is melt-refined and cast into anodes for electrodeposition of recyclable Ni-Co alloy. Melt oxidation using roasted superalloy grinding sludge as oxygen source can divert the Cr to the slag but with excessive Ni-Co loss. Melt oxidation-carburization or direct melt carburization retains -95 pct of the Ni-Co in the anode alloy. With direct carburization, -90 pct or more of the Cr and other refractory metals report to the anode alloy, largely as carbide phases insoluble in electrolysis. Electrorefining data relate parameters such as controlled cathode potential, Fe and Cr impurities, pH, and compartmented cell use, to current efficiency and Ni-Co deposit quality. Recovery of -90 pct of the Ni-Co in the scrap can be achieved. Preliminary experiments to recover Cr, W, and other metals from the anode sludge and other byproducts are discussed. 347

Jan 1, 1987

By Yasuhiro Konishi, Norizoh Saitoh, Toshiyuki Nomura

This paper describes a new recycling method, based upon biotechnology, in order to extract platinum group metals (PGMs) from post-consumer products. The metal ion-reducing bacterium Shewanella algae was found to exhibit the ability to reduce and deposit PGMs. An integrated bioprocess using Shewanella bacteria to selectively recover Pd, Pt, and Rh from aqua regia leachates of spent automotive catalysts is demonstrated.

Mar 1, 2017

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Hiromichi Ohta

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thermal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thermal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By Adolf Mikula

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of ternary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth, silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe element.

Jan 1, 2003

By Cui Wang, Qian Li, Kexin Jiao, Haibin Zuo, Jianliang Zhang

Abstract：A rational cooling water system is the assurance for long campaign life of blast furnace．In the paper, the heat transfer of different furnace period and different furnace condition based on the water quality characteristics were analysed, and the reason of the heat flux over the normal from the hydrodynamics was analysed. The results showed that, the vapour-film and scale existence significantly influenced the hearth heat transfer, which accelerated the brick lining erosion. The water dynamic characteristics of the parallel inner pipe or among the pipes were the main reason for the abnormal heat flux and film boiling. As to the reasonable cooling water flow, the gas film and the scale should be controlled and the energy saving should be considered.

Jan 1, 2015

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By R. F. Hammen

Heavy metal contamination of water is a problem of immense national and international proportions. However, effective cleanup is complicated both by the toxicity and the low concentrations of metals in wastewater streams. Using high performance chelation chromatography, the solid phase extraction and purification of extremely dilute metals from water was highly effective. The process is based on selective displacement of metals from a chromatographic column containing a chelating resin. The resin is characterized by extremely efficient adsorption kinetics which allow rapid and complete removal of the metals.

Jan 1, 1993

By Robin M. Forbes. Jones, Suhas V. Patankar, Ramesh S. Minisandram, Jr. Carter, Kanchan M. Kelkar

"The nucleated casting process currently under development has the potential for production of Ni-base superalloy preforms that possess superior microstructure to product made by conventional casting processes, primarily for gas turbine applications. In this process, electroslag remelted (ESR) clean (i.e., free of ceramic inclusions) molten metal is conveyed via a watercooled copper Cold-walled Induction Guide (CIG) to a gas atomizer. The spray of clean metal droplets is then directly cast into a water-cooled crucible for ingot production. The microstructure of the resulting ingot preform evolves within the length scale of the individual droplets and is a function of the thermal state of the incoming metal droplets. This, in turn, depends on particle size, flight time and heat exchange with the gas phase.In the present study, computational models is developed for the analysis of the flow and heat transfer in the gas-metal spray system under axisymmetric and steady-state conditions. The gasphase flow is analyzed using an Eulerian framework and turbulent mixing within the gas phase is modeled using the two-equation k-e model. The dynamics of the metal particles is analyzed using a Lagrangian framework that involves calculation of the trajectories of the metal droplets. A two-way coupling is considered whereby the transport and heat transfer in the gas and the metal phases influence each other.The analysis is developed at two levels. The spray model performs a detailed calculation of the spray dynamics in the vicinity of the spray and is intended for predicting the temperature and mass flux distributions of the metal spray depositing into the mold. The chamber model enables prediction of gas flow and motion of metal particles in the entire spray chamber."

Jan 1, 2004

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of titanium oxycarbide – a consumable anode material used in molten-salt processes for electrowinning titanium – from heavy mineral concentrate, such as a high-titania leucoxene and natural rutile is described. The oxycarbide is prepared by carbothermic reduction of the oxide at elevated temperature. Particle size distribution (of the titanium oxide raw material) and temperature have large effects on the kinetics of the reaction, which seem to follow a “shrinking-core” model. It is anticipated that low porosity (in the anode pellets) would be advantageous during electrolysis. Particle size distribution, extent of reaction during carbothermic reduction, and sintering temperature are expected to affect pellet porosity after sintering, and are being tested experimentally.

Jan 1, 2015

By KNona C. Liddell

Goethite is an important naturally occurring sorbent for divalent heavy metals and has often been used as a model compound in studies of adsorption on oxide mineral surfaces. Surface complexation modeling, surface spectroscopy, and electrochemical techniques have all been applied to goethite adsorption. Modeling studies have shown that usually several different sets of fitted parameters are equally successful in representing surface charging and adsorption data. Surface spectroscopic data are proving valuable in determining the nature of the surface sites, and refined models now incorporate structural information on interatomic distances and coordination numbers. Multisite surface complexation models can give very good fits to surface charging and adsorption data, but further improvements are needed to better represent surface reactions involving exchange of protons and divalent cations. Recent experimental and modeling studies on adsorption of divalent transition metals on goethite are described and the present status of the field is assessed.

Jan 1, 1999

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004

By Mikio Kobayashi

Extraction of valuable metals from sulfide ores continues to be a very important, process and so the strict control of discharge of harmful metals in effluents from refineries becomes more important in the future. The recovery methods for heavy metals have been developed. Some metals such as Se and As are still difficult to be removed to very low concentration, although the techniques for recovery and removal for many kinds of heavy metals have already been developed. Especially, in case of Se the recovery system from water with low concentration has not be developed yet, although the WHO decided Se to be harmful for human beings and then the discharge control is under obligation now. In general Se exists as selenite ion and/or selenate ion in aqueous phase and selenite ion is able to be recovered by coprecipitation with ferric hydroxide or by reduction to solid selenium by general reductants. Selenate ion, however, has a strong resistance to conventional treatments. Therefore the new technique for the recovery of Se from water including selenate ion has to be developed. In this presentation the new approach for removal of selenate ion using the reaction in which ferrous ion is oxidized to ferric ion is presented. Selenate ion is reduced to selenite ion during the reaction and then to solid selenium, while ferrous ion is oxidized to ferric ion. The coexistence of activated carbon is very useful to increase the reaction rate. The use of iron powder is also effective and very useful for reducing gel-like precipitates mainly consisted of ferric hydroxide. The concentration of the residual selenate ion is probably under 0.1 ppm after recovering Se by the mentioned-above approach. In addition to the mechanisms of these reactions, the effects of pH, coexistent positive and negative ions, and reaction temperature are also presented. Furthermore the investigation of the behavior of selenosulfate is presented.

Jan 1, 1998