Search Documents

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness' of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By Corby G. Anderson

In nature, mercury is quite commonly found in association with antimony ores. This can be as a separate mineral such as cinnabar or in direct association with the antimony ore. The most common antimony-mercury mineral is livingstonite that occurs in places such as Algeria, Mexico, USSR and China. In the Roznava deposit in eastern Slovakia, tetrahedrite ore containing mercury ore has historically been processed pyrometallurgically for its silver and copper values. As well, in Tajikistan, major antimony deposits there contain significant mercury ore concentrations within the stibnite ore body. The mercury contained in these materials poses both a processing and environmental challenge. This paper will outline the processing of these types materials by industrial alkaline sulfide hydrometallurgical methods. The economics relevant to this potential application at Roznava in Slovakia will be outlined.

Jan 1, 2003

By R. Ratnagiri, B. Minaie

"In order to expeditiously produce defect-free metallic components in materials processing applications, the relationship between the process parameters and the product properties needs to be well understood while minimizing the production engineering iterations. To achieve this goal, a realistic mathematical formulation of the process should be carried out and an appropriate numerical modeling of various phenomena occurring in such process should be implemented. The materials processing of transforming the molten material into a finished metallic component involves fluid flow and solidification/melting. In the present paper, a finite element based analysis of the fluid flow ·and solidification/melting phenomena in cavities is presented and the various issues in modeling these phenomena are discussed. These transport phenomena play an important role in determining the final characteristics and material properties of the part by affecting the formation of defects and microstructure. A realistic numerical modeling of these phenomena can significantly reduce the rejection rates during the process and can increase the quality of the final product.IntroductionDuring the intelligent materials processing of various metallic components, it is often required to have a thorough knowledge of the behavior of the transport phenomena involved in this process. This is due in large to the coupling that exists between the transport phenomena and the final material properties of the components produced during materials processing. This interrelationship demands that the pertinent transport phenomena in the form of fluid flow and solidification/melting be studied and predicted accurately. In many materials processing applications, the fluid flow is in the form of either a forced convection free surface flow intended to fill a cavity or a natural convection flow resulting from the gravity when the cavity is filled. In either case, the phase change in the form of solidification/melting is also involved in order to complete the process. However, the thermal history during this phase change has a direct impact on the material properties of the final part and the possible defect formation that may be involved. This thermal history itself is dependent on the nature of the fluid flow during the earlier stages of the process. As such, there is a coupling between the fluid flow, phase change, microstructure, and defect formation in the resulting component. It is therefore necessary to analyze these phenomena in order to find optimum methods to produce good quality parts by minimizing the defects that may be generated. Such an analysis can result in the development of appropriate numerical models for the process that can facilitate the economical and timely manufacturing of various components with high consistency. The present paper discusses the issues related to the transport phenomena encountered during materials processing of components engineered largely by using various combination of convective fluid flow and solidification/melting in cavities."

Jan 1, 1994

By Peter Hayes, Evgueni Jak, Ata Fallah Mehrjardi

Modern analytical tools, such as electron probe X-ray microanalysis (EPMA), are used in experimental characterization of phase equilibria and microstructures of complex slags. Integrated thermodynamic computer packages, such as FactSage, are used to provide more accurate descriptions of complex slag systems. These advanced methodologies have been applied to characterize dynamic steady state freeze linings in slag systems using submerged cold finger probes at controlled laboratory conditions, establishing the effects of bath chemistry, temperature, heat extraction rate and bulk fluid flow. It has been found that stationary freeze lining deposit interface temperatures at steady state conditions can be lower than the bulk slag liquidus temperature, and that stable operation below the liquidus is possible. A conceptual framework has been developed to explain the phenomenon and the range of interface temperatures that can be obtained in dynamic steady state conditions. These findings have important implications for the design of freeze linings and possible improvements to high-temperature metallurgical operations.

Jan 1, 2014

By Fathi Habashi

The behavior of pyrite, covellite, and arsenopyrite during leaching is different from other sulfides due to the presence of the disulfide ion, Sl. Arsenopyrite contains in addition, the diarsenide ion, Asl. The disulfide ion undergoes auto-oxidation in high acidity leading to elemental sulfur and sulfide ion formation: The sulfide ion may oxidize further by oxygen to elemental sulfur if high acidity is maintained. In neutral medium, the disulfide ion does not undergo auto-oxidation but oxidizes to thiosulfate then to sulfate: This leads to the two overall reactions observed experimentally: In acid medium and in neutral medium Covellite and arsenopyrite behave similarly.

Jan 1, 1995

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By Gerald M. Ellis

Exploration for gold .deposits on Hispaniola has taken place sporadically over the years but has expanded in the past decade. There are veintype, disseminated, alluvial and elluvial deposits. Investigations were previously undertaken in Haiti by combined Haitian, Bureau of Mines, and UN geological teams at Grand Bois Limbe(Milot) and Cap Coq areas. Later studies were conducted at the Miches and Moncion districts. Gold occurrences were reported in quartz, silicic-barite veins and gossans. An important deposit ?at Pueblo Viejo is? a disseminated type where extraction is taking place in the oxidized zone. Exploration by Japanese and West German firms with local geologists are described in this paper together with Pueblo Viejo, Miches, Restauracion, Milot, and Meme ?areas where occurrences are known. Copper deposits with associated gold va1ues are also described. These include vein deposits in Central Cordillera and disseminated deposits at Terrier Rouge and Blondin.

Jan 1, 1989

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Nobuyuki Masuda

In Japan, the municipal solid waste, which amounts to 50 million tons, is generated every year and most of it is incinerated. The fly ash from the municipal waste incineration (the primary fly ash) contains heavy metals, such as lead and zinc, etc., and dioxins. In case of melting, the fly ash from the process (the secondary fly ash) contains high concentration of heavy metals (e.g., Zn; 1-20%, Pb, 1-10%). Metal Mining Agency of Japan launched a four-year project in 1999 to establish the integrated technologies to recover the valuable metals from, and to decontaminate, the primary and secondary fly-ashes in the practical scale by utilizing the existing metallurgical processes and facilities, along with the energy saving. The segregation, flotation and chemical treatment are applied to the treatment of the primary fly ash. The secondary fly ash is treated with MY (Mitsui-type blast furnace) Process after the chlorine removal to recover the heavy metals in the ash, In this paper, the segregation and flotation process for primary fly ash and MF process for secondary fly ash are explained. The main results of experiments done from 1999 to the mid of 2001 to design the pilot plants and to optimize the operating conditions are described. The main results of the experiments are as follows: - The segregation reaction of Cu was confirmed by the experiment on the treatment condition of 800 and 900`C with adding oil cokes and water to the primary fly ash, and 99.98% (toxicity equivalent) of the dioxins were decomposed by the treatment. - Washing tests of secondary fly ash to feed MF resulted that more than 70% of chloride were removed, but still lower than expected, and agglomeration tests were successful by the results of the sufficient strength of briquettes produced though a little more binder for the agglomeration is required than usual operation. - Smelting experiment by downsized MF showed that valuable metals, such as zinc and lead, are recoverable in the furnace dust. Recovery ratios, Zn: 58% and 67%, Pb: 74% and 83%, are accomplished.

Jan 1, 2002

By Richard Elliott

Current methods for producing low-carbon manganese alloying materials for the steel industry are energy intensive and costly. To enable wider implementation of high Mn steel alloys, a novel solid-state Mn ore reduction strategy is therefore being investigated. This solid-state process, modelled on existing Direct Reduced Iron technology, employs a methane-containing atmosphere to reduce Mn ore pellets to a metal carbide. These pellets may then be smelted, yielding a Mn-rich master alloy. It is well established that CH4 is a suitable reductant for Mn ore powders; however, the reduction behaviour of industrially relevant Mn ore pellets by CH4 is poorly understood. The present work reports the results of an investigation undertaken to address this knowledge gap. The results of this study highlight the significantly different reduction behaviour exhibited by the Mn ore pellets relative to the ore powder under similar conditions and suggest that the diffusion of CH4 into the pellet interior is the limiting factor in achieving complete reduction.

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By P. A. Davidson, D. J. Short

"In this paper we describe a 'non-contact' electromagnetic nozzle suitable for sprayforming and gas atomization processes. In such processes there is a need to control the flow rate and diameter of the liquid metal jet whilst minimising contamination of the stream. This can be achieved using an electromagnetic valve, which partially levitates the jet in freespace, using a segmented cylinder surrounded by an induction coil. This valve will significantly enhance the quality of the titanium alloys and nickel-based superalloys used in sprayforming and gas atomization. This paper describes the design and test of a laboratory prototype valve based on experiments performed with liquid tin.1. Introduction In many industries there is an increasing need for clean, high quality metals and alloys based on titanium and nickel. Two important processes are: 1) Spray deposition which allows the liquid metal to be converted to a near-net shape, thus alleviating the need for subsequent forging and extensive machining and; 2) Powder production of titanium by gas atomisation.In centrifugal spray deposition of titanium (see figure 1) the metal is induction melted in a cold crucible. The crucible consists of a number of water-cooled segments, which allows the high frequency magnetic field of the coil to pass through the crucible, and into the melt. The charge is melted by the induced eddy currents. Locally at the crucible walls the liquid metal solidifies, and is contained within a. 'skull' of its own solid, thus reducing contamination from the crucible wall. Once melted the metal is poured through an electrically heated graphite nozzle and into the spray forming chamber. The principal limitation of the process to-date, however, is that it currently uses a graphite and /or ceramic nozzle to direct the flow of liquid metal to the atomizing disk and as such there is considerable risk of nozzle erosion with inevitable effects in terms of contamination of the melt stream and variability in flow conditions. In this research programme we develop a. non-contact electromagnetic nozzle, which will totally eliminate refractories and/or ceramic materials from the melting and casting process. This will greatly enhance the technological capabilities of sprayforming and gas atomization processes."

Jan 1, 1999

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By Tracy Lucas, Ian Hamill

"Issues of importance in the area of continuous casting centre around product quality. This can be affected by particle inclusions transported into the mould from upstream processes and by draw-down of particles from the meniscus. Turbulence of the meniscus can increase the latter and is also detrimental to product surface quality.Suitably validated Computational Fluid Dynamics (CFD) modelling can provide the operator with an efficient tool with which to investigate the effects of changes to the design and operation of the caster and associated plant.In this paper, examples are presented of the use of the CFD software, CFX, to simulate:•,free-surface shape and turbulence in the mould using deforming meshes•,solidification in the mould using a fixed-grid, source-based method•,argon gas injection through a submerged entry nozzle using a full multiphase model•,inclusion motion and removal in tundishes using an algebraic slip model.The CFD simulations of the free surface shape are complemented by detailed Particle Image Velocimetry measurements performed on a full-size water model of a thin-slab mould and upper strand. Close agreement is demonstrated between the predictions and experiments."

Jan 1, 1999

By Y. Houbaert, L. Kestens, R. Decocker

"A magneto-elastic model is presented to calculate the orientation dependence of the magnetostrictive strain, observed at saturated magnetisation in ferromagnetic materials with a cubic crystal structure and an arbitrary crystallographic texture. The formula of Becker and Doring is used to express the anisotropy of magnetostriction for a single crystal. In order to simulate the macroscopic average magnetostriction of a polycrystalline aggregate (with an arbitrary texture) the Reuss assumption of the elasticity theory was applied. According to this assumption the various orientations of the polycrystal can defonn without constraints, producing local strain incompatibilities in the microstructure but observing total stress equilibrium. The macroscopic strain is calculated as the weighted average of the individual strains of all orientations composing the polycrystal. The weight factors are determined by the volume fractions of the corresponding orientations of the given texture, which can be measured by standard X-ray diffraction techniques. The model is applied to simulate the variation of magnetostriction (at saturation) with respect to the rolling direction for a standard grade of Goss-oriented electrical steel. A brief comparison with experimental data allows validating the basic model assumptions. IntroductionBecause of tougher environmental constraints, the noise reduction in transformer cores has become increasingly important. It is generally accepted that the main source of noise is magnetostriction, which is known to be caused during the magnetisation process by the movement of 90° magnetic domain walls and the rotation of the magnetisation vector out of the easy directions. Therefore, it is obvious that when a ferromagnetic body is magnetised to saturation, the resulting magnetostriction will be dependent on the distribution of magnetic domains in the initial state.In the literature two coefficients are used to describe the resulting magnetostriction at a saturating magnetic field. The total strain, measured from an arbitrary demagnetised state to technical saturation, is called the saturation magnetostriction, and is denoted by (~)s. The tenn magnetostriction coefficient will be employed to designate the strain measured from the ideal demagnetised state (i.e. one in which no preferred orientation of domains exists) to technical saturation. Failure to recognise the difference between these two quantities has led to considerable confusion in the literature.The magnetostriction coefficient for a single crystal is a well-known property for ferromagnetic cubic materials. In 1939 Becker and Doring [1] have derived the following relation, describing the magnetostriction coefficient for single crystals with a cubic symmetry:"

Jan 1, 2001

By Adam Powell

A Cahn-Hilliard phase field model is formulated to describe transport-limited electrochemical reactions coupled with fluid flow in a metal reduction cell. When the reaction is limited by mass transfer of metal ions from the electrolyte to the cathode, the metal-electrolyte interface at the cathode exhibits a Mullins-Sekerka instability, leading to the growth of dendrite-like "streamers" of liquid metal into the electrolyte, which in turn significantly enhance the apparent mass transfer coefficient there. Model results for iron reduction from ferrous oxide in slag show formation of these streamers. Although the double-layer is not included in this model, the related phenomenon of electrocapillarity can be represented by a gradient penalty term which includes the electric potential gradient, such that interfacial energy is a function of the electric field normal to the interface.

Jan 1, 2003

By George Owusu

A study has been carried out on the use of solvent extraction, instead of the traditional zinc dust cementation process, to remove copper from concentrated zinc sulphate leach solutions. In a series of experiments using plant solution containing 1.9 g/L Cu, 2 g/L Fe, 173 g/L Zn, 7.9 g/L H,SO,, 0.25 g/L Cd, 15 mg/L Co etc. and LIX 622 in SX-1, up to about 97-98 % of copper present in the zinc sulphate leach solution was extracted with negligible co-extractions of zinc, iron, cadmium, cobalt, etc. pH modification was not required for this reagent. The copper loaded organic was almost completely stripped using 150 g/L sulphuric acid. Investigations into the effect of any possible organiclextractant contamination on zinc electrowinning showed (if any) little effect on current efficiency if the organic contamination is less than 45 ppm; current efficiencies of 95-97 % were obtained. At organic contaminations higher than 45 ppm, the current efficiency dropped to about 92- 94 %. Visually, the organic-contaminated cathode sheets had rough surface morphology, becoming more intense with increasing organic concentration, compared to the non-contaminated cathode sheets.

Jan 1, 1998

By Tao Zeng, Jianchao Li, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"The densities of the selected quaternary Ca0-5%Mg0-Alz03-Si02 slag with low silica were measured by the Archimedean method in a wide temperature range from l 723K to 1823K. Slag compositions were chosen based on five different levels of Si02 content between 0.00 pct and 11.40 pct. The MgO content was equaled to 5.00 pct. The mass ratio of CaO/Alz03 was varied from 0.67 to 2.14. The effects of temperature, Ca0/Alz03 ratio and optical basicity were studied. It is shown that density decrease approximately linearly with an increase in temperature. With the same Si02 content, the density decreases with increasing of CaO/Alz03 ratio and optical basicity. Based on the experimental data as the boundary of the homogenous phase region predicated by F ACTSAGE software, the mass triangle model is used to calculate the density of selected limited homogenous phase region. The results showed that the mass triangle model is working well.IntroductionIt is of great importance to measure density of slag melt not only to the theory research for melt, which that is directly amenable to the structure correlations of molten slags, but also to the industrial application. Many metallurgy phenomena such as inclusion formation in molten melt and its removing, slag foaming, slag-metal reaction are closely related to the density of slag. Density is also required to estimate other fundamental properties, like surface tension, viscosity, and thermal conductivity from thermal diffusivity so that a relatively complete picture in regard to the behavior of high-temperature molten oxides could be made."

Jan 1, 2013

By W. Kasprzak

Modern light metals processing technologies are very complex and involve a diverse set of variables that must be quantitatively evaluated. The most effective way to design new casting processes that deliver specified metallurgical and mechanical properties is to develop a method of simulating the "real-time" process within a test sample of sufficient size. The results can then be analyzed and the required optimizations can be performed. This paper presents a novel method of simulating the industrial casting processes in a laboratory environment using an experimental apparatus based on the principle of high frequency induction heating. The applicability and accuracy of the proposed analytical method is demonstrated, for example, by simulation of the solidification and heat treatment of a test sample composed of two dissimilar materials. The simulation can be used to develop a stress model for an engine block made from an aluminum based alloy with iron cylinder liner inserts.

Jan 1, 2002