Search Documents

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By John B. Cocanour

The U.S. Bureau of Mines (USBM) has developed a laboratory-scale on-line analysis and process control system for a decopperization electrolytic circuit. This system is software driven, running on a 486DX-33 personal computer (PC) utilizing a portable energy- dispersive x-ray fluorescence (XRF) spectrometer as the sample analyzer. The XRF copper reading obtained was used as the control variable through an RS-232 serial interface to the PC for software-based control of feed flowrates. When the copper concentration in the electrolytic cell (as measured by the XRF) deviated from the set point, the feed flowrate to the cell was automatically altered using software-based proportional-integral-differential (PID) computer control to yield the desired copper concentration at the electrolytic cell outlet.

Jan 1, 1994

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By K. Morsi

Carbon nanotube (CNT) reinforced metallic composites have been recently generating significant scientific interest, due to their expected superior properties compared with other composites. Out of the metallic matrices investigated for reinforcement with CNTs, aluminum has received considerable attention. A major problem has been the dispersion of CNTs in metallic matrices. This paper discusses preliminary results on the mechanical dispersion of CNTs in aluminum powder, powder processing, stability and characterization of aluminum dispersed with CNTs at reinforcement levels equal to and below 5 wt.%.

Jan 1, 2009

By Tian Sugui

By direct aging treated, creep properties measurement and microstructure observation, the influences of the direct aging treatment on the creep behaviors of Hot Continuous Rolled GH4169 superalloy are investigated. Results show that the creep resistance of Hot Continuous Rolled GH4169 superalloy may be obviously improved by directly aged treatment. Under the applied stress of 700MPa at 660, the creep lifetime of the alloy is enhanced to 126h from 60h. During hot continuous rolling, the deformation features of the alloy are the twinning and the double orientations slipping of the dislocation activated within the twinning regions. After direct aging treated, the alloy displays a smaller grain size, and the finer g² phase is dispersedly precipitated in the matrix of the alloy, which is thought to be a main reason of enhancing creep lifetime of the alloy.

Jan 1, 2010

By Victor Raul Alarcon

The Ilo Refinery was commissioned in 1975, with a cathode production capacity of 150,000 tpy. In 1994, Southern Perú Copper Corporation (SPCC) purchased the Refinery from Minero Perú SA. Subsequently, in November 1999, Grupo Mexico acquired control of Southern Perú. The anode production facility is located at the Ilo Refinery. A number of effective operating and quality control practices have been developed that have improved anode quality, as well as increasing anode production capacity to 350,000 tpy. These, and other optimization actions have allowed for a current density increase from 213 A/m2 to 275 A/m2, while maintaining current efficiency at 98% and sustaining the high quality of the cathode. The paper will outline the scope of operational practices in the Anode Plant and provide some discussion on the Ilo Smelter modernization project, and the resulting impact on the existing anode plant.

Jan 1, 2005

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Larry M. Southwick

Considerable process and equipment development and analysis were conducted during design of Freeport Sulfur's laterite nickel facilities in the late 1950's. These covered ore concentration at Moa Bay, Cuba, and concentrate refining at Port Nickel, Louisiana. Both facilities utilized acid pressure leaching and product refining steps that were similar to those later used elsewhere in the laterite processing industry. Unfortunately, developments in Cuba removed the Moa Bay facilities from Freeport control. This deprived the project of a start-up that would have allowed thorough resolution of difficulties and a quicker attainment of production capacity. This meant lost opportunity to positively prove and complete the technology when optimum resources and staff were available. This paper reviews the original rationale of how design was developed via laboratory, bench scale and pilot studies by Freeport Sulfur. Some later operating problems will also be discussed. This case is unusual, but the lessons learned may be instructive in the application of difficult and complicated technologies, as well as the need to understand and retain access to the original development and design activities Keywords: Moa Bay, Freeport Sulfur, Port Nickel, acid pressure leaching, pilot plant, pachuca, Chemical Construction, pressure letdown, cobalt, titanium

Jan 1, 2004

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920's with in situ operations in the underground mine and small dumps up to the 1950's. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased' to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By Brian Lightfoot

Ausmelt technology is a versatile bath smelting technology with application in many waste treatment fields at low capital and operating cost. Heavy metals extracted from wastes may be recycled to mainstream use and the slags produced will be inert and suitable for use as aggregate, shotblasting grit or other applications.

Jan 1, 1994

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By Frank A. Vonesh

In order to reduce the amount of visible, airborne emissions in the Metals Industry, a new Industrial Gas Technology was developed by Air Liquide. This patented technique is called ALECT?, Air Liquide Emission Control Technology. Demonstrations have been conducted for many cutting and lancing operations as well as for hot metal transfer from vessel to vessel. Fume reductions of 90% and greater have been achieved in actual practice. Air Liquide continues to improve the process and the associated control equipment.

Jan 1, 1994

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Nomenclature: A: area (m2), C: heat capacity (WIK), cp: specific heat (J/Kg K), d: internal tube diameter (in), F: correction factor for multi-pass and crossflow heat exchanger, h: convective heat transfer coefficient (W/m2K), k: thermal conductivity (W/mK), L: length (m), m: mass flow rate (Kg/s), W: flow rate, N: number, Q: heat rate (W), R: thermal resistance, T: temperature (°C), U: overall heat transfer coefficient (W/m2K), ;1,,P: pressure drop (Pa), ;1,,T: temperature difference (°C), p: density (lb/ft3), N: number of tube passes, U,: velocity in tubes, iJh: head loss in feet of flowing fluid, Up: velocity in the pipe leading to and from the heat exchanger (ft/sec), µ: viscosity ( cp ), Llpf frictional pressure loss (psi/l 00 equivalent ft of pipe) Subscripts: b: baffle, c: cold, cf counter flow, ex: exchanger, f: fouling, h: hot, i: inlet-inner, ib: inlet baffle, lm: logarithmic mean, m: mean, o: outlet-outer, s: shell, t: tube, w: wall AbstractThe main bottleneck for primary aluminum production industry is dealing with a huge amount of input energy. The fact is that part of provided energy to aluminum production smelters will be lost as waste heat and it never used for aluminum production. One part of waste heat is escaping from the potroom exhaust gases, which was studied for possible recovery in a desalination plant to produce distilled water and the paper was presented in 2011 TMS Annual Meeting. However, it was shown that waste heat recovery plant to produce distilled water is highly profitable but the main fact is that the exhaust gases from potroom are highly corrosive, abrasive and dusty. The main challenge for desalination plant construction, which is using aluminum smelter exhaust gases as the main heat source, is the highly corrosive environment that makes the situation difficult and complicated for equipments design and plant construction. In this paper, we are trying to study a detailed investigation regarding the heat exchangers fouling, corrosion in heat exchangers including heat exchangers' material, how often we need to shut down the plant for maintenance or cleaning, and plant thermal efficiency with considering fouling."

Jan 1, 2012

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010