Search Documents

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By R H. Knight

Production mine geology must be accurate and efficient in order to reduce risk and ensure that ore value and mining operation revenue are maximised. Present grade control practices are commonly based on outmoded and inaccurate 2D geological mapping techniques where spatial relationships are estimated by eye, sketched by hand and projected to arbitrary reference planes. The 3D mapping approach outlined in this paper integrates 3D photogrammetric imagery with implicit modelling techniques to enable more accurate grade control and reconciliation in underground mines. High-resolution stereo photographs are taken of daily ore development headings. Ore contacts are traced directly on a 2D face photo using a stylus and rugged tablet. Area-weighted face grades are estimated and calculated on mapped 2D face planes. In the office, a 3D photorealistic mesh is processed and georeferenced. 2D face mapping data is transformed into its actual 3D location and true 3D mine mapping is performed by digitising oriented 3D polylines representing ore contacts and other geological features directly onto the image surface. Three-dimensional spatial relationships are fixed, eliminating the projection error of traditional 2D methods. Ore envelope and waste solids are modelled within the closed, drift-round mesh. Volume-weighted ore envelope and round grades, as well as round volume and tonnage, are calculated. Ore/waste classifications, grade, tonnage and per cent dilution are quantified per round, visually assessed in 3D and reconciled with short- and long-term models on a daily basis. Updated geological continuity models provide geological guidance in development headings under geological control and accurate 3D structural and form-line mapping improves definition drilling and stope planning. Three-dimensional imagery provides a permanent detailed survey and geological record of mine workings that can be revisited virtually to reinterpret geological ore controls in light of new observations and insights. In addition images can be used to monitor daily production performance, create training scenarios for miners, engineers and geologists and prepare management presentations. This approach adds value to underground mines by improving the accuracy and efficiency of mine geology practices. The method is particularly effective in mines with visually distinct and geometrically complex orebodies, such as those in the Balmat zinc mine located in New York State, USA, which are used to illustrate the method.CITATION:Knight, R H, 2017. 3D mine mapping – improving grade control and reconciliation in underground mines using photogrammetric imagery and implicit modelling techniques, in Proceedings Tenth International Mining Geology Conference 2017, pp 203–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

The Department of Mineral Resources has a statutory responsibility for mine site environmental management and control in New South Wales. The Department is focusing on an environmental management systems (EMS) approach, as a management tool to achieve æbest practiceÆ outcomes both within our own organisation and on mine sites. One of the DepartmentÆs tools is environmental risk assessment and management which incorporates the Mining, Rehabilitation and Environmental Management Process (MREMP). The MREMP was introduced many years ago in order to integrate the activities of key stakeholders who may have a material interest in the mine. The MREMP provides an ideal mechanism by which ædue diligenceÆ requirements and environmental management programs can be integrated into mining operations and lead to a sustainable post-mining land use.

Jan 1, 2002

By Andrew Allan

[Research conducted by the Bureau of Mines hrinq the last 5 years on the uce of machines for 7!naer:rolmrl ?.eve loym~nt in pi.t,c hlng anthracite beds l~a~ provide? data ?howin? that ?:;panrt of thc roof an9 str?eg of thes? oTen - jnqs requires almst half of' the PRS? workin? time. The possibilitie~ of i!rinz a mvable,. te1.ee*co@. c tpr? 3f ?tee1 ~h-!.oltl at the face in~tetcrl of conventional wood a*ti~yorts w?r? si:~q~eteil by engineers engaqad on the~ work If ~uch a shi~l8 COLI.~,~. be ~sve~.~yad, it tnillil man that face workera w~uld be provi8ed with mulrnu.m prot?ct+on from falls of' roof and ribs mi! the en- tire ehift could he I~W? Lo ~lro,J.~:ce cocl. Fermanent tim3er coald be p'l.acnA behind the shielR independently of the 'face work as the face advanced.]

Jan 1, 1953

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By A. V. De Forest

INSPECTION and test methods of great diversity have been used from the most ancient times to select raw material, control its manufacture, and appraise its finished properties and value. The "miller thumb," expert in grading flour, the vintner's sense of taste, the goldsmith's micro-wear test on a touchstone, the enquiring sniff over the doubtful egg -these are all nondestructive inspection methods, accurate and depend- able, but not readily reduced to numbers in the c.g.s. system. A horse trader inspecting a possible purchase is interested in more than age, size, weight, color. heredity, speed, or drawbar pull which can be reduced to figures. Behavior, temperament, stamina, health-past, present and future---are just as important as the numerically determinate constants.

Jan 1, 1940

By B. R. Waples

The first reaction in organizing a project of magnitude is that it's the same as smaller projects -- just bigger. This is not totally correct. The industry's record of completing big-money jobs on time and within budget is not outstanding. From a personal point of view, my question is: What is the project size at which controls are lost? Is it controls? Is it the number of pieces of equipment? Is it the number of decisions to be made? The slowness of communications? Or is it a combination of all of these? In working on multimillion-dollar jobs, the percentage of overrun seems to be lower or show an underrun when the following basics are followed: 1) Preplanning is intensified 2) Data gathering is complete 3) Approach is optimized 4) Planning is realistically scheduled 5) Changes are minimized 6) Decisions are expedited

Jan 1, 1982

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By W. W. Adams, T. D. Lawrence

"The National Safety Competition covering the calendar year 1934 was the tenth yearly safety contest conducted by the United States Bureau of Mines. Participating in the competition were 334 mines and quarries in 38 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies ""Sentinels of Safety.""Since these annual contests were begun 10 years ago by the United States Bureau of Mines the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the prevention of accidents has been achieved, as is indicated by an almost constant downward course in toe accident-frequency rates for the contest group as a whole during the past 10 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the decade and a downward trend during the latter part of the period except in 1930 and 1934; in each of those years a disastrous explosion with abnormally heavy loss of life occurred at the property of one of the participating companies.Because of the abnormal nature of the major disaster in a bituminous-coal mine in 1930 and 1934 the accident-severity rates for the bituminous group for those years are not strictly comparable with the rates for other years. The rates for bituminous mines for 1934 in the present report have therefore been computed on two bases; first, to exclude the record of the company that suffered the disastrous explosion and, second, to include the record of this company. The first rate represents the normal experience of the bituminous coal companies unaffected by the disaster and is therefore more indicative of the real trend of the accident rates for this class of mines from year to year. The latter rate shows the actual experience of all bituminous mines in 1934. The report of the competition of 1930 likewise showed the rates for the bituminous group as computed both with and without the disaster that occurred that year.The National Safety Competition is conducted by the United States Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the facts contained in the accident reports which the competing companies furnish to the Bureau to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest."

Jun 1, 1935

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By L O. Filippov, C H. Veloso de Melo, A Correa De Araujo

Froth flotation of iron ores is one of the most widely used methods to upgrade iron ore into high-grade concentrates. In recent years, reverse cationic flotation of iron ores has been specifically the subject of several studies. Since quartz is the most common gangue mineral in iron ores, understanding the behaviour of this mineral was the main target of the majority of such studies. However, with the depletion of mineral deposits considered rich and easy to process, it has become more common to find iron ores with complex gangue minerals, which are composed not only of quartz but by a variety of silicates. The mineralogical composition of the ore is an important factor for determining reagents and mineral processing parameters. The mineralogical suite of an ore also presents a paramount role for operational optimisation of any given flotation process. Some studies were performed with different types of amphiboles and other Fe-bearing silicates, for example, but the influence of the mineralogical nature of these silicates in reverse cationic flotation has not been fully explored and will be discussed here. Changes in the traditionally used reagent scheme for reverse cationic flotation, generally including alkaline pH values, polysaccharides as depressant (mainly starches) and primary ether amines and diamines, are expected when dealing with iron ores with complex silicate gangue composition.CITATION:Veloso de Melo, C H, Correa de Araujo, A and Filippov, L O, 2017. Reverse cationic flotation of iron ores with complex silicate gangue minerals, in Proceedings Iron Ore 2017, pp 241–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By R. S. Adhikari

The changes in defects patterns or in element condition index during visual inspection of bridges are primary concerns for inspectors. This paper presents a new approach for change detection of defects in bridges by identifying changes in texture patterns through spectral analysis of digital images. The commonly used method for change detection is image differentiation. This subtraction method requires images to be of same size, scale, and rotation. However, no two images are same in real practices. Thus, image registration is required to align images and to produce change maps. This process is tedious and it is difficult often to achieve a good registered image. But, the change detection task can be readily modeled in frequency domain for texture patterns discrimination and also for quantifying their properties. This paper proposes a novel approach for change detection by transforming digital images into Fourier spectrum. In new coordinate system, 1-D signature functions can be drawn which facilitates easy comparison of textures in different directions. The proposed methodology provides useful tools for comparison of inspection history graphically and quantitatively. In practice, expensive sensors are used to detect subtle change in defect patterns. The proposed method can be used to detect any subtle change in defect patterns using digital images at much lower cost.

Aug 1, 2013

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009