Search Documents

By Gerald C. Smith

Introduction Newmont Mining Corp.'s Carlin Gold Mining Co. mines gold ore and waste material from four open-pit mines in Northeastern Nevada. Combined production rate is 24.5 Mt/a (27 million stpy). The company is producing gold bullion from the 2.4 kt/d (2600 stpd) Carlin Mill No. 1. and the 2.3 kt/d (2600 stpd) Maggie Creek heap leaching plant. In August 1985, the 6.3 kt/d (7000 stpd) Carlin Mill No. 2 at Gold Quarry came on-line. The total combined throughput of 11.2 kt/d (12,000 stpd) will make Carlin Gold Mining one of the largest US gold producers. Feasibility studies are underway to increase the total gold out-put from Gold Quarry. This will be done by adding a continuous dump-leaching process that will recover gold from lower grade ore. History In 1961, Newmont exploration geologists located claims in the Lynn Creek mining district near Carlin, NV. An exploration drilling program revealed significant gold mineralization. A stepped-up drilling program revealed an ore body with an estimated 10 Mt (11 million st) of ore containing 109 t (3.5 million oz) of gold. Test results in 1963 allowed metallurgists to develop the flowsheet and design for a 1.8-kt/d (2000-stpd) countercurrent decantation (CCD) cyanide plant. Carlin Gold Mining Co. was formed to operate the property. Carlin purchased its first mining equipment in 1965. This consisted of two Bucyrus-Erie 2.7 m3 (3.5 cu yd) shovels and nine 27.2 t (30 st) Wabco Haulpak trucks, two Inger¬soll-Rand track-mounted drills, one Chicago Pneumatic T-650 rotary drill, one rubber tired Michigan 280 dozer, one Caterpillar D-8 36A track dozer, one Caterpillar 16 motor grader, and the necessary ancillary equipment. The fleet was capable of mining 3.2 Mt/a (3.5 mil¬lion stpy) working two eight-hour shifts, five days a week. In 1967, one P&H 1500 3.8 m3(5 cu yd) diesel electrical shovel and three 59 t (65 st) Dart trucks were added to the fleet, along with a Chicago Pneumatic rubber tire mounted rotary drill. This equipment addition increased the mining capabilities to 5.7 Mt/a (6.3 million stpy). Three separate pits, the Main, East, and West, within a 1.6-km (1-mile) radius of the Carlin mill were being mined. The crew consisted of 46 hourly men and three supervisors. This equals 497 t/ total hourly manshift (548 st) or 407 t/total manshift (515 st). Rising gold prices in the early 1970s allowed lower grade deposits to be mined at greater distances from the mill. The Boot-strap pit, 19.3 km (12 miles) north of Carlin, was started in 1973. Two Hough 45.4 t (50 st) front-end loaders, four Wabco Haulpak 45.4 t (50 st) trucks, and a second track type D-8H dozer were added. The higher grade ore was trucked to the Carlin mill using three

Jan 11, 1985

By John R. Shattuck

The Shasta and California Iron-ore deposits are 14 miles northeast of Redding, Shasta County, Calif.; and since 1907 have produced more than 300,000 short tons of exceptionally pure iron ore. Although some ore was mined and smelted from 1907 through the First. World War, most of it has been produced from 1942 through 1945 for use in making heavy ship ballast and concrete anchorages for mines. Irregular masses of magnetite, ranging from lumps of a few tons to pods containing about 25,000 tons, occur associated with skarn near the contact between the McCloud limestone and a younger granitic intrusive. Some of the deposits are low-grade, whereas others are nearly pure magnetite. Selective mining and hand sorting are necessary to produce a high-grade product. Investigation of these deposits by the Bureau of Mines included 2,910 feet of diamond drilling, some surface sampling of the principal mineralized zone and beneficiation tests. Resulting factual data are given in the body of this report.

Jan 1, 1948

"7.1. Glossary of the Platinum-Group Minerals7.1.1. IntroductionA glossary of the platinum-group minerals (POM) serves as a useful introduction to a chapter on their mineralogy. Earlier glossaries (Cabri, 1972, 1976) were prepared for different purposes and composed in a different manner. As for most mineralogical textbooks, from Dana's System of Mineralogy, 3rd Edition (1850) , to Fleischer's Glossary of Mineral Species (1980), this glossary is primarily a chemical classification, arranged here in two tables. Table 7.1 groups the mineralforming compounds of the six platinum-group elements (POE) according to their essential anion(s) or according to the nonPOE element in intermetallic compounds. Table 7.2 is a similar listing for the native metals and alloys of the POE. Both tables include unidentified POM considered to be bona fide new minerals requiring additional study for complete characterization and recognition (see Chapter 9*). Some information on the chemistry of the POM is given in the sections on X-ray data (7 .2) and ore microscopy (7 .3). Because the overwhelming majority of POM have been characterized by the electron microprobe, a more detailed account of representative analyses is given in Chapter 8**. The total POM listed in Tables 7.1 and 7.2 is about 100, after deleting some which would not qualify as discrete species if found today, but which are still recognized on historical grounds; e.g. iridosmine, osmiridium, platiniridium. Tables 7.1 and 7.2 also include 28 unnamed POM; included because they are considered to be probably new species (Cabri 1981 b). The referral scheme for unnamed minerals is the same as in Chapter 9. There are considerably more palladium minerals known than other POM; the proportion of total species (listed in Tables 7.1 and 7 .2) for the POE is: Pd 48%, Pt 21 o/o , Ru and Ir 9% each, Rh 8% and Os 5%. These proportions are in marked contrast to the estimated cosmic abundance, as compiled for average type C1 chondrite by Naldrett and Duke (1980): Pt 29%, Ru 20%, Pd, Ir and Os 15% each, and Rh 6%."

Jan 1, 1979

By Jay S. Gunasekera

Since great emphasis is being placed on the manufacturing science and processing science programs in the Department of Defence and other government research agencies and industries; currently, extensive research on computer aided design(CAD)/ computer aided manufacturing (CAM)/ and computer aided engineering (CAE) is being conducted at Ohio University (OU) . OU has invested over a million dollars in CAD/CAM hardware and software. Design and analysis packages like ALPID, NIKE, STREAM, SHEAR, POLY_FLON, RINGROLL have been developed or modified at OUusing finite element method, finite difference techniques or enhanced slab analysis. Packages like ABAQUS, FLUENT, and NASTRAN have been extensively used.

Jan 1, 1990

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By Lester F. Engle

Books have been written, complex charts drawn, great batches of punched cards handled by ever increasing numbers of computers, and innumerable meetings held-all for the purpose of making effective the ultimate objective of new, revised or improved process facilities. It is to the credit of management, engineers, and others that in the vast majority of cases, the outcome of their work has been technically sound and economically rewarding. There is a way, however, to insure even better results.

Jan 5, 1966

By P. J. Rider

Diamond Value Management?s objective is to achieve $/ton revenue improvement across De Beers group mines. The respective %improvement contributions are measured against targets set by each of the operations. Degree of target achievement is measured via a maturity model at each operation. DVM comprises seven elements. It spans several value chain facets and various collaborative projects are conducted under its umbrella. New technologies in De Beers are also evaluated from a DVM perspective.

Jan 1, 2003

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

By F K. Buckley

Currently, Kanieri Gold Dredging Limited operates the only large scale gold dredging operation in New Zealand. It dredges a claim in the Taramakau River using the bucket dredge 'Kanieri'. This dredge, a 'Yuba' type, was designed and built in the 1930s. On the current claim it works about 12 hectares of ground a year. Because of its design, the tailings from the 'Kanieri' make land restoration difficult. This was unimportant until it commenced its new claim ML-32-310 in 1978. The conditions, attached to this licence required it to restore the land for afforestation, the designated use fur the Crown land being mined. With the company planning to work future claims on the Grey River, it decided to undertake restoration work on the Taramakau to demonstrate its capability of establishing pasture land on tailings, a more difficult task than restoring the land for afforestation. After two years and the restoration of two blocks totalling 22 hectares, reasonable pasture establishment has been achieved. Much has been learned to date and further refinement of the techniques used will take place over the next two years. The quality of the tailings produced has improved as a result of the limited modifications possible on the existing dredge. This has been significant in achieving better results. The knowledge gained will be taken into account in future dredge design. Both the Company and its Consultant are confident of achieving satisfactory restoration of dredge tailings for pasture land.

Jan 1, 1981

By Don Phelps, John Hawley, David P. Field

In recent years observational techniques of tunneling have become increasingly popular methods to facilitate complex underground infrastructure projects. The traditional design and construction management practices developed in Europe have been adapted for application in North America to suit a more restrictive management and legal culture. This paper will discuss three recent projects, the San Diego Mission Valley East Extension, Washington Dulles International Airport People Mover, and the Seattle Beacon Hill Station and Tunnels, with the objective of identifying the challenges of applying observational tunneling methods to established contractual practices in North America.

Jan 1, 2005

By Willard P. Ward

SOME TIME in the year 1874 or 1875, I conceived the idea that spiegeleisen might be made -in a blast furnace from ores that were not carbonates, and which did not contain both manganese and iron in the same ore. Up to this time, such ores had formed the basis of all the spiegel that had been produced; and all the ferromanganese that was on the market before 1875 was made in crucibles, and cost about 00 per ton, for 80 per cent. Mn. I consulted the great steel metallurgist of the day, Alexander Holley, who listened attentively to what I had to say, and told me he did not think my plan was practical, so I abandoned it for the time being. But I was so stubborn that I could not get the notion out of my head. It seemed to me that a good metallurgist should be able to work the thing out in some way. I had already had some experience in smelting refractory lead ores in Utah, and was young and not lacking in self confidence, so after waiting a bit, I got Anton Eilers, the best all-around metallurgist I knew, and J. H. Bramwell, the best iron blast-furnace man I knew, both intimate friends of -mine, to come to my place in Bartow County, Georgia, and look over things. They remained for several days, and made all the examination they thought necessary; and they also advised me to give up the project, and either to keep the furnace running on car-wheel iron or to blow it out. After my talk with Holley, I improved my plant in several ways. I closed the top of the furnace, put in a hot-blast stove, a steam boiler and a Weimer blowing-engine which gave me blast enough, at a pressure high enough for all the requirements of, the furnace, and which I could bring up to a temperature of 600° to 700° F.

Jan 1, 1921

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937

Research into the mechanisation of ore winning from the very narrow reefs characteristic of South African gold mines has been conducted from as early as 1964 through the Chamber of Mines Research Organisation (COMRO) but with limited success. However, the Council for Scientific and Industrial Research (CSIR) has recently re-evaluated the potential for the mechanisation for the narrow tabular gold mines. It has been determined that there are approximately 22 000 tonnes of gold left in-situ in channel widths of less than 500 mm in thickness. The extraction of ore from such reefs requires a complete paradigm shift in that the current mining cycle (drilling, blasting, cleaning and supporting) is not feasible since such a stoping width would not allow the workers entry into the stope. Consequently, a non-entry form of mining is required. With this target in mind CSIR has invested in a project called the Nederburg Miner which seeks to identify new technologies for drilling, rock breaking, cleaning, and materials handling, the application of which will enable non-entry mining of very narrow ore bodies. The intention is to develop a fully automated system that will not require human involvement at the stope face. The outcomes of research into this proposed system will not only extend the life of South African gold mines but will also enhance South Africa's reputation for excellence in mining research. This paper presents the new technologies under consideration and potential methods for their application into an integrated non-entry mining system.

Jan 1, 2008

By J. H. East, D. Harrington

"INTRODUCTION Shaft mines, coal and noncoal alike, have a common hoisting problem that remains largely unsolved - how to obtain a mechanical device that will suspend a cage or skip in a mine shaft if the hoisting rope should break or become detached from the cage or skip and that will function effectively under all conditions of service. Safety catches, or safety dogs, as they are commonly named, are installed on nearly all mine cages and many skips operating in American mines, but often, if the hoisting rope breaks, the cage or skip falls to the bottom of the shaft in spite of safety devices, causing much property damage and often fatalities.Available information relative to safety catches for mine cages and skips, desirable characteristics of safety catches and methods of testing safety catches to determine whether they are functioning correctly has been assembled in this publication for the convenience of those responsible for the safe operation of mine cages end skips and, more particularly, to focus attention on the need for a device that actually will stop and suspend a falling cage or skip under all conditions of use and do it without killing or maiming the occupants."

Feb 1, 1948

By H Utama, hi, A Suw

PT. Indo Muro Kencana (PT.IMK) is gold and silver mine located in Central Kalimantan province, Indonesia. Mining activities in PT.IMK is conducted in Bantian pit area by applying surface mining method and using combination of excavator and hauler (articulated dump truck and rigid haul truck) as the transportation for ore to the crushing plant and waste material to the waste dump. Current blasting practice is ore-waste blasting. Ore-waste blasting is the term where the ore and waste rock are blasted in the same blasting process. Blasting is conducted by using nonel initiation system. By multiple pits operation, monthly powder factor is varied from 0.23 kg/t to 0.27 kg/t. Emulsion blend with density 1.15 g/cc is used as bulk explosive. At this stage, the concept of geoblast is proposed as an engineering tool for Drill and Blast engineering practice in PT.IMK. In addition, there is a need to maintain rock fragmentation by blasting, to maintain monthly powder factor, and to maintain excavator’s productivity. Next, the concept of scaled depth of burial (Chiappetta and Treleven, 1997) and the concept of blastability index (Lilly, 1986) are proposed as geoblast’s tools to improve blasting practice in PT.IMK. It is expected that rock fragmentation by blasting, explosive consumption and excavator’s productivity will be maintained by integration of geoblast and drill and blast engineering. Furthermore, the objective of this paper is to integrate geoblast and drill and blast engineering in order to create an engineering guideline in PT.IMK. Additionally, blasting trials with air decking application is proposed in order to support the geoblast’s improvement. It is planned that these blasting trials will be conducted in 2022. In conclusion, it can be seen that integration of geoblast and D&B engineering in PT.IMK is relevant to improve current drill and blast current practice and applicable to maintain rock fragmentation by blasting.

Nov 29, 2022

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel frame- work buildings started toward the end of the last century. Progressively the requirements be- came more stringent, crushed bank slag, weighing 80 lb per cu ft as com- pared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft.

Jan 1, 1949

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

In Southern Africa, historic mining and mineral processing of base metal deposits have almost exclusively focussed on the extraction of major metals, leading to the loss of remaining valuable raw materials into tailings dumps and waste rock piles. At the Namib Pb–Zn mine (Erongo Region, Namibia), historic base metal tailings deposits are present as unreclaimed exposed waste piles. The tailings comprise silt- (fraction A: d50 = 25 to 48 μm) to sand-sized (fraction B: d50 = 86 to 185 μm; fraction C: d50 = 210 to 230 μm) material and contain major concentrations of base metals (Pb av. 1.15 mass%, Zn av. 3.20 mass%), S (av. 9.95 mass%), as well as lower values of other metals (Cu av. 490 μg/g, Cd av. 133 μg/g, Ag av. 22 μg/g), and critical elements like Sb (av. 14.7 μg/g) and In (14.3 μg/g). Former mineral processing only targeted the extraction of galena and sphalerite. As a consequence, qualitative mineralogical composition of the tailings is similar to that of the primary ore. Ca–Fe–Mg(–Mn) carbonates, quartz, micas, chlorite, minor graphite, magnetite, and rare parisite relate to the former host rock and gangue matrix, whereas Fe-rich sphalerite, galena, magnetite, pyrite with minor pyrrhotite, rare arsenopyrite, marcasite, cassiterite, and accessory scheelite are original constituents of the primary ore. Reprocessing of such a material would be challenging, but a mixed Pb–Zn concentrate enriched in Cd and Ag might be obtained. In future, possible reprocessing of Namib tailings and associated disposal of wastes into an appropriately designed repository would not only generate valuable metal commodities, but such activities would also eliminate a major metal pollution source from the local environment.

Sep 9, 2024