Search Documents

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By W. A. McKinney

In conventional dump leaching of porphyry mine strip wastes, many years are required to extract up to 20 percent of the copper from the contained sulfide minerals. Furthermore, none of the molybdenum, gold, or silver in the strip wastes is recovered by current leaching practices. Because mineralization occurs predominately along fracture planes, breaking of the rock during mining operations liberates and concentrates some of the metal values in the fines. Research shows that upgraded fines can be screened from mine wastes and froth floated for early recovery of copper, molybdenum, gold, and silver. For example, screening a dump sample assaying 0.35 percent copper as chalcopyrite removed about 20 percent of the copper as minus 1/4-inch material that analyzed 0.6 percent copper. About 35 percent of the molybdenum and 20 percent of the gold and silver also reported in the fines. Crushing the mine dump sample to minus 3 inch before screening increased the distribution of copper and molybdenum in the minus 1/4-inch screen fraction to 28 and 50 percent, respectively. Similar results were obtained by screening fines from two other large samples of mine waste dump materials. Flotation studies established that the enriched minus 1/4-inch fines from the three dump samples could be effectively concentrated. Comparative testing revealed that the combination of froth flotation of fines and acid-ferric sulfate leaching of the coarser fraction enabled doubling the recovery of copper over direct leaching of the samples. In addition, significant amounts of molybdenum, gold, arid silver were recovered by flotation.

Jan 1, 1970

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine&apos;s requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By Alexis Cotrado

Shahuindo, es un yacimiento único en su género, se encuentra en un prolífico cinturón que produce oro en el norte de Perú, a 30 km al norte de la Unidad Minera La Arena. La operación es un tajo abierto usando operaciones convencionales de perforación/voladura, carguío y acarreo. El método de minado es a tajo abierto con un movimiento promedio de 87,500 TPD de roca y 36,000 TPD de Mineral. El presente trabajo muestra un ejercicio de optimización de las reservas minables comparando el valor del proceso chancado & aglomerado (C&A) y el proceso ROM, usando técnicas de optimización de la ley de corte para agregar valor al proyecto y cumplir con las restricciones operativas de Mina y Lixiviación.

Sep 29, 2023

By Warwick Hoffmann, Robin Batterham, David Conochie

CRA has been actively involved in developing a bacterial oxidation process for the treatment of low grade, refractory gold resources. Success in this application is dependant on the design of large, energy efficient reactors. It was identified at an early stage, that the conventional, bottom sparged bioreactor is inherently inefficient because air must be compressed to a pressure above that at the bottom of the tank. This inefficiency increases as the size of the reactor increases. CRA has developed a novel approach to the aeration problem. In this, venturi aeration is used to aspirate air into a liquor stream. The stream is then reintroduced at the top of a draft tube bioreactor. The advantages found with this technique include · low energy requirements and high oxygen utilisations. From results at the 30 m3 scale, we predict an energy usage of -500 kWh/t sulphur oxidised at a scale of 1000 m3.

Jan 1, 1993

By Richardo Montoya

Radomiro Tomic, the new CODELCO division, is a copper deposit located at 3000 m a.s.l. and 40 Km from Calama in northern Chile. It has total oxide reserves of 802,000,000 tonnes with an average grade of 0.59% total Cu (using a cut-off grade of 0.4% total Cu). The copper oxide ore is mainly atacamite and chrysocolla. Startup is expected to commence in December 1997 of 150,000 t/y of Cu cathodes. Future expansion to 250,000 t/a of Cu cathodes is currently being planned. The process consists of an open-pit mine, a two-stage crushing system, agglomeration with sulphuric acid and emplacement on a heap leach pad for a 45-day leaching cycle. Solvent extraction and electrowinning will produce LME "A grade cathode. A number of significant technology innovations have been incorporated into the project.

Jan 1, 1998

By Jesse O. Betterton

IN the last analysis, two basic factors influence the use of metals and alloys; namely, cost and adaptability to the use under consideration. These are so interrelated that to study the properties of metals or alloys without considering the prices and price trends is quite illogical. Lead has been a cheap metal, selling in 1932 for the extremely low price of 2.56 cents per pound. The cheapness of lead in the past was not due to a particularly abundant supply of the element in the earth&apos;s crust but rather to the ease with which it was won from its ores and to the chemical stability of the metal, preventing its dissipation. Today, however, our modern economy has caught up with the distribution of lead in the earth&apos;s crust and the price is largely dictated by the supply of concentrates readily available for smelting, and which can be placed quickly upon the market. The demand for lead, particularly in times of stress, has brought the price up to the level of 19 cents in the United States, where the price is controlled by Government decree, and the price has been even higher in the world markets. The higher price for lead has changed the uses for this metal to a marked degree, driving it out of the fields where it is not essential. Lead articles of great antiquity have been found in Egyptian ruins, proving the stability of the element and indicating the basic simplicity of its metallurgy. It is probable that lead was the first

Jan 1, 1953

By S. J. Schatzel

In order to better understand the effects of longwall mining on the methane reservoir overlying the panel, the National Institute for Occupational Safety and Health/Pittsburgh Research Laboratory (NIOSH/PRL) designed and implemented a vertical borehole monitoring experiment (BME) on an active longwall panel. The mine operates in the Pittsburgh Coalbed in Greene County, Pennsylvania. The BME site was located away from either end of the panel to avoid mechanical influences caused by the draping of overburden in this region and was positioned at the same distance from the tailgate gateroad as the mine?s gob gas venthole sites. The borehole drilling depths and monitoring intervals were chosen to address a different stratigraphic zone in each of the three planned holes. The monitoring boreholes were positioned perpendicular to face advance using a close spacing pattern of about 15 m (50 ft) between collars. Boreholes were instrumented downhole and on the surface for various measurements. It was observed from the field data that the gob gas venthole fracture network formed 24-46 m (80-150 ft) ahead of the mining face. Overburden permeability?s within the same test zones increased 100 to 500 times following undermining. The borehole test interval within the fractured rock responded to overburden gas pressure while the test interval in the caved zone responded to mine ventilation conditions. Eight months after the boreholes were undermined, slug testing indicated permeabilities had increased further in the fractured rock zone. Measurements of surface movement indicate that the permeability development observed in the boreholes is a product of vertical subsidence without lateral movement within the tensional rock mechanics zone on a supercritical longwall panel. Results from this study suggest that maximum permeability in the longwall panel overburden is achieved 58 to 190 m (190 to 620 ft) behind the longwall following maximum compaction of the overburden.

Jan 1, 2009

By Pedro Augusto David Machado

The hot metal produced in small blast furnaces runs with a highly heterogeneous charcoal. The result is a significantly higher hot metal chemical composition variation, especially for the silicon content, which varies from 0.4 to 1.5% in Mini Blast Furnaces - MBFs, designed to feed an EAF and/or a BOF. These MBFs operate with frequent variation in their productivities to feed preferably only one of the steelmaking reactors, that is, EAF or BOF. The hot metal suitable amount, chemical composition and temperature, to be delivered at the steelmaking vessel, become the major concerns in the integrated operation MBF to EAF or BOF. In order to cope with those undesirable frequent variations, a solution has been proposed based on the existing technologies of oxygen jets and ladle refining techniques adapted to a hot metal ladle or to a Torpedo Car. The proposed technique is not only able to adjust hot metal temperature and chemical composition, but it also generates the adequate conditions for refinement from P and S, as well as “cleaning” hot metal ladles and Torpedo Cars by melting pig iron skulls. Therefore, this new technique development results in high hot metal yield, an adequate chemical composition and bigger campaign of hot metal ladle.

Aug 17, 2017

By N. B. Prenn, R. H. Robinson

"The model described is a design and economic planning tool for analyzing surface mineral deposits. Mineralization, topography, costs and significant geologic features are input to the model. The results are:(i) final pit limits yielding the maximum total profit,(ii) annual cut-off grades and plant sizing yielding the maximum present value, and(iii) annual maps of the pit and annual production statistics for the mine, concentrator and smelter.Additionally, summaries are printed of the block mining sequence and cash flow. A special feature is an option to include dump-leaching operations. Stockpiling of material can also be simulated by the model. The model is built around theories of dynamic cut-off grades and a pit design algorithm. The dynamic cut-off grades maximize present value by examination of all economic and physical constraints for the optimum combination. The pit design algorithm is a set of rules formulated to find the maximum value from a special graph. The graph is different from graphs of analytical geometry, being made up of points and arrows connecting some of the points. These graph elements describe the relationship between any point in the deposit and the material which must be mined to get at that point. The model was designed to bring together the interdependent theories of economics, pit design and production scheduling."

Jan 1, 2014

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By Pascal Lesagel

Life Cycle Assessment (LCA) is a holistic environmental assessment tool that allows the compilation and evaluation of the inputs, outputs, and potential environmental impacts of a product or service throughout its life cycle, from cradle to grave (i.e., from resource extraction and transformation to final disposal, including production and use stages). The relevance of LCA for the mining industry is twofold. First, the mining industry has a role in providing the LCA community the data that allows subsequent evaluations of the life cycle environmental impacts of primary materials such as metals, as well as the environmental comparison of the downstream products of the mining industry with other competing materials for specific uses. Second, the mining industry can use LCA in order to evaluate the environmental impacts of its activities, identify their environmental hotspots and compare the impacts of available technical options. For example, the environmental impacts of different extractive and processing technology can be compared through the use of LCA. This latter use of LCA by the mining industry is less common. This paper discusses the use of LCA to compare sulphidic tailings management options. The paper also presents some of the LCA research challenges that still have to be addressed to increase the relevance of LCA results for the specific context of mining activities.

Nov 1, 2008

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By J. M. Garcia

This paper highlights several management practices from the oil and gas industry to support the proposition that financial performance in the finite, non-renewable resource business relates more to upstream rather than downstream activities. Based on the analysis of nine oil and gas companies, this study supports a previous study involving fourteen mining companies that showed reserves growth is one of the main levers of value creation in mining. Interestingly, this study also finds that the oil and gas industry has been historically more profitable than mining. The reason, it is argued, is that oil and gas companies count on management practices that focus primarily on the upstream segments of the business, compared to the traditional downstream focus of mining. This paper delves into these ideas to conclude that what mining may need to improve its competitive advantage is a new organizational framework. Another conclusion is that the upstream management focus is vital not only for strategy formulation in the resource business, but also for policy formulation in economies based on the export of finite, non-renewable resources.

Jan 1, 2011

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By E. Ilgar

Biodegradation of spodumene by Asnergillus niger has been investigated. This organism oxidizes sucrose to citric and oxalic acids (in approximately 50-sot proportions) which degrade the spodumene mineral. The kinetic effects of leach variables on the dissolution of lithium were determined. The maximum theoretically attainable rate of lithium extraction was calculated for the effect of pulp density, to be V : 3.01 x 10 kg m sand the corresponding constant value, K = 12.47% pulp density. The apparent activation energy of lithium extraction vas found to be ^E = 20.3 kJ and frequency factor A = 5.66 x 10 s for S-spodumene leaching by synthetic -3 citric and oxalic acids (each in 0.05 kmol m-3 concentrations).

Jan 1, 1989

By Joseph M. Hans

INTRODUCTION The decontamination of a uranium mill site is principally an earth moving task. The task can be completed effectively and efficiently by selecting the proper earth moving equipment and using that equipment within its particular constraints for decontamination work. A considerable backlog of experience concerning earth moving equipment selection and use was acquired during the decontamination work conducted at the former Shiprock, New Mexico, uranium mill site. This experience was acquired by trial and error while decontaminating over a wide range of depths and different types of terrain. Many different types of excavation equipment were available to the Shiprock decontamination project because the Navajo Engineering and Construction Authority (NECA) heavy equipment operator&apos;s school was doing the decontamination work and a variety of equipment was needed for training. The equipment is described and its general use for decontamination is discussed. Its on-the-job use for decontaminating the Shiprock millsite is presented. [EARTH MOVING/ANCILLARY EQUIPMENT DESCRIPTION AND DECONTAMINATION CONSTRAINTS] Tractor-Scrapers The most commonly used scraper is the bottom-dump type because it is highly mobile and can dig, carry, and spread loads. In this type a tractor is connected with a yoke to a scraper bowl (Figure 1). The bowl is essentially a rigid box that pivots around the rear axle, opening to the front. A hardened steel knife, or bit, is attached to the leading edge of the bowl. When scraping, the bit penetrates and forces the earth overlying the bit edge into the scraper bowl as the scraper moves forward. When the bowl is full, it is closed by lowering a closure or apron against the cutting bit. The load is dumped while moving, by raising the apron and forcing the load from the bowl with a crowd, or ejector. The height of the dumped load is controlled by adjusting the bit height when dumping. Scrapers of this type generally do not have enough power to scrape up loads unassisted. Loading assistance is generally provided by a crawler tractor that pushes from the rear against the scraper&apos;s push block. Some scrapers are made self-loading by adding an additional engine for the extra power needed for the load pick up. Another commonly used self-loading scraper uses a loading elevator (Figure 2). The elevator consists of two roller chains carrying crossbars. The elevator is rotated when scraping and the crossbars cut the earth above or in front of the bowl bit, forcing the load into the scraper bowl. No apron is used on elevating scrapers. The load is dumped by partially retracting the bowl floor and pushing with an ejector. Scrapers have some undesirable characteristics when used for decontamination work. One characteristic is that a clearance space exists around the apron when it is in its closed position. Part of the load (especially sandy soils) dribbles through the

Jan 1, 1981