Search Documents

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated data base was used, which included 1728 ore blocks with ‘actual’ grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ‘actuals’/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. 2-. 3- and compound-lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2003

By W. Dutton, D. Simms

"The clearing of tuyeres on copper and nickel converters or similar metallurgical, vessels has, for many years, been done using mainly a manually- operated ""puncher"". One such device is the ""Gaspe Puncher"" developed in 1962 at Noranda's Gaspe Smelter. In an attempt to remove the operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor.The automated puncher is controlled by a Texas Instruments Model 530C Programmable Controller (PLC). Position measurement and control is done using non-contact position measuring equipment from the Tele-Controls Division of Geodimeter Inc. The entire automation system was installed on an existing Gaspe Puncher with minimum disruption to the operation of the smelting process. The operator's panel allows the user to ""block out"" any individual tuyere, and to select any of a variety of operating modes.The development of the automated puncher is described, and the results of several months operation are given.IntroductionThe tuyeres of copper and nickel converters and similar metallurgical vessels become blocked with solidified material formed by the cooling action of the blowing air. This restricts the converting operation. Clearing these blocked tuyeres has for many years been done mainly using a manually-operated ""puncher"" which uses a hydraulic or pneumatically-operated piston to drive a steel bar into the tuyere. The Gaspe Puncher, developed at Noranda's Gaspe Smelter in 1962 is one such device. It is currently being built and sold by Heath & Sherwood (1964) Limited, under license to Noranda. There are over 200 units in operation world-wide.In an attempt to remove the Puncher operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, and to increase productivity, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor. This paper describes the development of the automated Gaspe Puncher, its installation at the Horne Smelter, and the results of its operation after several months."

Jan 1, 1989

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By L Langer, R Simcock, M Davis

Rehabilitation of mining sites helps to achieve the purpose 5(2c) of The Resource Management Act 1991 û æavoiding, remedying, or mitigating any adverse effects of activities on the environmentÆ. The environmental outcomes for recent and current mining operations on the West Coast are variable. There are some exemplary mining operations which are restoring or even improving land use and environmental factors in the region, particularly those operated by the larger mining companies. There are also examples of an exploitative mentality where the environment and land have been severely degraded by mining activities. Technology has been developed to prevent a repetition of the historical destruction of the environment through mining. Failure to rehabilitate mined land is no longer acceptable to the New Zealand public in the 1990s and damages the credibility of the mining industry. Examples of successful mine site rehabilitation to pastoral farming and to production or plantation forestry are illustrated from the alluvial gold mining industry. Planning, sequencing of operations, the utilization of sailor plant growth materials, and aftercare are key factors in successful land rehabilitation to these productive uses. There is also a recent focus on restoring indigenous forests and wetlands at both coal and gold mining sites, particularly for mines on or adjacent to the conservation estate. The results of scientific research and efforts by the industry on techniques for rehabilitating rainforest and pakihi wetland after mining are presented, particularly from the Giles Creek Dunoille Coal Mine. There is a need for further research and trials to apply and extend rehabilitation techniques to other geological and environmental situations, particularly to mines in mountainous areas and to difficult environments like the coal measures ecosystems of the plateaux above Westport.

Jan 1, 1996

By Run-sheng xu, Hai-yang WANG, Di ZHAO, Teng-fei SONG, Jian-Liang Zhang

This paper was mainly focused on the different semi-cokes and charcoal which could be new fuels for blast furnace injection. Through the comparative study with bituminous coal and anthracite coal, the properties of semi-cokes and charcoal were presented in this research. 10 indexes of different fuels were obtained by different standard experiment, including proximate analysis, ultimate analysis, igniting point, explosivity, transportation characteristic, ash properties, grindability, calorific value, combustibility and reactivity with CO2. According to the data analysis, it provided a theoretical basis for rational utilization of various blast furnace fuels, and helped to broaden the scope of the blast furnace injection fuels. This research could contribute to energy conservation, emissions reduction, and sustainable development of iron and steel enterprises.

Jan 1, 2015

By Georges J. Kipouros

Anhydrous neodymium trichlorids (NdCl3), containing ~1 weight percent neodymium oxychloride (NdOCI) was prepared by the dehydration of neodymium trichioride hexahydrate (NdC13.6H2O). Dehydration of the hexahydrate was conducted in three steps. First, the hexahydrate was slowly heated in air to about 250 °C until all the low temperature water of crystallization was removed. In the second stop, the neodymium hydroxychloride (Nd(OH)2C1) fanned in the first step was decomposed by heating under argon to 430 ° C. Finally the salt was ground and then treated with HCl gas at 330 °C until practically all of the NdOCl was converted to NdCl3.

Jan 1, 1992

Brunswick Mine, one of the largest underground zinc mines in the world, is scheduled to close in 2010 after almost half a century of production. All mines eventually close; some suddenly as a result of unsustainable economic or technical conditions and others, as in our case, as a result of the depletion of the orebody. When the mine is the most significant employer and an economic driver in the region, it is key that the closure is handled in a planned, communicated, well-executed fashion. The following paper documents strategies, plans and activities that are currently taking place in order to ensure a seamless closure that satisfies all stakeholders including employees, management, regulatory bodies and the public. It is an important deliverable for the company that the good will, credibility and reputation that has been built up over the years is sustained throughout the closure process and beyond. A life of mine labour agreement with the unionised workforce, staff retention and recruiting programs, regulatory closure plans, communications and transition adjustment activities will be discussed. The use of a stage-gate style project management tool analysing the risks and key deliverables will be highlighted. It is hoped that the concepts and approaches discussed here may be of value to other operations that will be faced with closure, and its inherent challenges, in the not too distant future.

Jan 1, 2006

By Gunnar Persson

The borehole pressure/time history of blasting practice is simulated in a twin pendulum apparatus, where the expanding shotfiring gases force two steel slab swingers apart. A pilot installation built at SveDeFo is described. The relevant factors, that govern the use of this test method as a means of classifying explosives with respect to their toxic fume potential, are described.

Jan 1, 1996

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

By Martin G. Castro, Renato G. Bautista, Morton Smutz

During the last 25 years, multistage mixer-settlers have been used extensively for liquid ion exchange work. The mixer-settler has the advantage of being a compact device in which a large number of stages can be assembled in a relatively small area. They are particularly advantageous for the separation of rare earths. Most of the adjacent rare earths have separation factors which are near one, which means that a large number of stages are needed to produce a good separation. When two elements (m, n) are extracted simultaneously, the separation factor (ßm, n) is defined as: [ ] where Ym, Yn are the molarities of the respective elements in the organic phase and Xm, Xn, are their molarities in the aqueous phase at equilibrium. The industrial consumption of rare earth oxides rose to over 6800 tons in 1968, an increase of 33% over 1967.1 The increased production and demand for rare earth and lanthanum chlorides for petroleum cracking catalysts was one of the principal factors in this increased consumption of rare earths. In 1968 approximately 59% of the rare earth oxides produced were used for gasoline cracking catalysts in the form of rare earth and lanthanum chlorides. There was also an increase in the sales of lanthanum oxides for use in optical lenses and in fiber optics. The future looks good for the rare earth industry. The rare earths can be expected to be used in many new products which are being developed. Until the late 1950's tributyl phosphate (TBP) was the principal solvent used in rare earth liquid ion exchange. In 1957 Peppard3 reported the use of di (2-ethyl-hexyl) phosphoric acid (D2EHPA) as a solvent for separating the rare earths. Rare earth separation factors of up to 2.5 were obtained in nitrate and chloride systems while the maximum separation factor using the

Jan 1, 1972

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By Doug Smith, Ross MacFarlane

"The Star Lake Mill was commissioned by Cameco (formerly Saskatchewan Mining Development Corporation) in 1986 to process a small high grade gold deposit in a remote location of Northern Saskatchewan. The lean approach to the 200 t. p. d. CIP mill to minimize capital and operating costs employs a number of unique features which are described along with highlights from the initial two years of operation.1.0 INTRODUCTIONThe Star Lake Mine is located 520 kilometers north of the City of Saskatoon (Fig. l) with the nearest population centre in La Ronge 130 km to the south. Gold showings were first discovered in the area in the 1940's with the Star Lake ""21 Zone"" ore body discovered in 1983. The Star Lake Mine started operations in 1986 becoming the first primary gold producer in Saskatchewan in over 40 years. The mine is operated by Cameco (formerly SMOC) with 50\ ownership in a joint venture with starrex Mining Corporation (35\) and Uranerz Exploration and Mining (15%).The limited reserves coupled with the remote location and the price of gold ($300-$350 u.s./oz) at the time the project feasibility was being assessed required a lean approach to make the short term operation successful. This paper describes the approach taken in the design and construction of the Star Lake Mill and describes the mill operation with highlights of the initial two years of operation."

Jan 1, 1989

Geological information is essential for a diversity of public and other purposes, including land use planning, hazard mitigation, and the exploration and sustainable use of natural resources. This is especially important in New Zealand, where the complexity of the geology is due to its position on an active plate boundary - the ultimate cause of earthquakes, mountain building, subsidence and volcanic activity. The geological setting also controls the origin and distribution of New Zealand's varied mineral and energy resources. Providing information about the origin, quality and quantity of mineral resources has long been seen as a key function of national geological organisations such as the Institute of Geological and Nuclear Sciences. Such information is essential for wise land-use decisions under the Resource Management Act. One of the major goals of the Institute is to quickly and effectively disseminate research results to interested users. The most effective and internationally accepted method of presenting geological data is by means of geological maps, which show the distribution of rock types and structural features at the surface. Most countries have ongoing gelogical mapping programmes, and in recent years the need for up-to-date, reliable information has led to a trend to accelerate basic geological mapping (eg US National Geological Mapping Act 1992; Australian National Mapping Accord 1990; Plan 2000 in the UK). Over the last 25 years, the Institute of Geological and Nuclear Sciences and its predecessors (NZ Geological Survey and DSIR Geology and Geophysics) have concentrated on detailed mapping of priority areas selected on the basis of economic and scientific interest. This has included remapping of Nelson-West Coast and Coromandel, regions with high mineral potential, for which 1:63 360 or 1:50 000 maps have been prepared.

Jan 1, 1994

By G Lumley

PlannersÆ optimism (or maybe commercial necessity) means that most mine plans use equipment rates that are rarely achieved (Lumley and Beckman, 2009). This lack of understanding of what equipment actually moves is causing erroneous equipment forecasts, leading to incorrect mine development plans and economic evaluations. Compounding this problem is a downward trend in actual equipment performance in some areas. Consequently, the presentation of realistic mine plans that are actually achieved in practice is not a common occurrence. However, rational, fact-based mine planning is available to those who want it. Hundreds of millions of cycles of data from open cut mining equipment has been collected from mines around the world since 1992. This unique and highly valuable databank is growing at an exponential rate and is being used by a number of our big miners to support rational and fact-based decision-making. However, neither the use nor the appreciation of the value of this data is universal. There is a challenge to everyone in the mining industry - how do you access value from it? The databank was drilled into and the results analysed for, the Australasian Mining and Metallurgical Operating Practices (AMMOP) publication (Lumley, in press). For this paper the analysis has been extended to include interpretation of trends for draglines, shovels, excavators and trucks. It investigates trends between coal and non-coal mines and across geographic areas. It is known that mining equipment performance in most sections of the industry is falling. This paper attempts to quantify the fall and provide explanations. The trends are analysed to extract the reasons behind the changes and most importantly, what can be done about it.CITATION:Lumley, G, 2012. Understanding trends in performance of open cut mining equipment, in Proceedings Project Evaluation 2012 , pp 203-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By D Craw

Sulphur-rich minerals such as authigenic pyrite (FeS2) are commonly associated with coal mine workings. Metallic elements such as arsenic (As), copper (Cu) and zinc (Zn) are enriched in the pyrite relative to their concentrations in the surrounding environment. Exposure of pyrite and coal to air and water results in a series of oxidation and hydrolysis reactions that are commonly catalysed by species of Thiobacillus bacteria. These reactions lead to a lowering of the pH in the drainage waters (acid mine drainage, AMD) and subsequent mobilisation of trace metals in environmentally significant concentrations. This study assesses the spatial distribution of As, Zn and Cu concentration in water in relation to pH and Eh (redox potential) downstream from the tailings at the Wangaloa opencast lignite mine in southeast Otago. This mine was abandoned in the late 1980s due to a decrease in the economic viability of mining the lignite. The area is showing the characteristic symptoms of AMD, which is detrimental to the health of several Pinus radiate growing on some of the tailings. The pH of the drainage waters can get as low as 2, and in some instances, lower, but it returns to near neutral (pH 6.5) up to 200 metres down stream from the base of mine waste piles. It is well documented that the atmospheric oxidation of pyrite is catalysed microbially, causing a substantial decrease in the pH of the drainage waters. Acidification is then counteracted predominantly by natural abiotic remediation processes occurring downstream.

Jan 1, 1999

St. Peter sandstone is very different from the minerals and rocks that have been studied extensively in mining. On the one hand, it is brittle as characterized by an unusually high friction angle and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, the geotechnical properties of the St. Peter sandstones were investigated through a comprehensive research program, which included uniaxial test, triaxial test, porosity test, thin section, X-ray diffraction (XRD), and scanning electron microscope (SEM). The specimens used for the uniaxial and triaxial tests were specially prepared because of the highly friable nature of the St. Peter sandstone. Thin section, XRD and SEM were utilized to examine the effect of the microstructure of the St. Peter sandstones on its strength characteristics.

Feb 27, 2013

By P. J. Brereton-Stiles, C. J. Hockaday, I. J. Barker, M. S. Rennie

This paper reports on studies that have been done on the electrical conduction in silicon, ferro silicon, and charge chrome furnaces. A system has been developed that can distinguish between normal resistive conduction and arcing, and this was used to quantify in particular the relative amount of arcing that takes place in these furnaces. It was found that silicon and ferro silicon behave similarly and exhibit a relatively large amount of arcing. Charge chrome on the other hand exhibits considerably less arcing, and the extent of this arcing is highly correlated with the tapping of the furnace. The arcing measurements can also be used online in the control of the furnace, both for the electrodes and electrical circuit, and for the raw materials.

Jan 1, 2007

The Effect of Mineral Liberation on the Floatabilities of Pyrite, Arsenopyrite and Arsenian Pyrite for Carlin Trend Ores

Sep 13, 2010