Search Documents

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By WALTER S.

(New York Meeting, February, 1912,) THE earliest example of attempting to form finely-divided materials into larger masses for better adaptation to commercial use was probably the briquetting of peat and lignite-waste at Paris by the use of a clay binder. It was from this attempt that our word briquette has arisen (Fr. la brique), the formed masses being shaped similar to ordinary bricks. This term does not, however, lend itself to the many shapes of such formed material as are now being produced, as few of them aside from some of the European brown-coal products bear any resemblance to the shape of that well-known article. The term "agglomeration " has therefore been chosen as more accurately descriptive of the products now being manufactured, this term including the molding as well as the sintering. With the increasing prices of fuel and ores and the greater demand for economy in the operation of industrial plants, more ,attention has been paid in recent years to the utilization of waste products and low-grade ores and fuels. Much of the waste has been occasioned by the inability to utilize finely ,divided ores and fuels in the furnaces because they could not be kept there, or else because they clogged up the furnace-shaft so that gases could not be forced through under ordinary conditions of operation. As a result, all such fines were thrown on the dump. Again, with the exhaustion of the richer deposits of ores, concentration of lower-grade ores becomes a necessity, and most concentrates are produced in a finely-divided condition. Aside from these considerations, there is also the economy in the cost of operating the plant; a furnace running on agglomerated material will have a much greater output than one working on fines. In one instance the charge of an iron blast-furnace was changed from fine concentrates to briquettes and the output was increased four-fold; better results could have been obtained had facilities been at hand for taking care of the increased output.

May 1, 1912

By Cade Mweemba, Alex Mwanza, Jackson Sikamo

"The Zambian Copper mining industry as we know it today has its genesis from early in the 20th century in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production going from zero to a peak of 769 000 tons of copper in 1969. At the same time, the industry created jobs to the extent that in 1972 the industry had over 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level at the dawn of the 21st century in the year 2000 when production was 250 000 tons. In terms of jobs, an average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000. Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and investments of over USD 12 billion, the industry production levels increased year- on-year to reach a peak of 763 000 tons in 2013 with direct jobs reaching 90 000. This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support to other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies and human capital. This is looked at particularly in the light of current challenges the industry is facing and makes suggestions on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2015

By AIME AIME

TWENTY-TWO sections and all four of the divisions sent delegates to the annual meeting. They became so interested in the wide ranging dis6ussion of old and yet ever-new problems of Institute affairs that three instead of two sessions scheduled were necessary. Monday morning the meeting assembled with President Bassett presiding in the absence of President-elect Tally, who had been called to Baltimore by the serious illness of a brother. Thursday morning Vice-president Turner presided until Mr. Tally appeared after which the latter guided the sessions. Since reports from all of the active sections save one had been mimeographed and sent in advance to the delegates, detailed reports from each were dispensed with. The discussions dealt largely with membership problems, both local and national, with financing, speakers and programs, visits from national officers, and the conduct of the annual meeting. Many interesting and constructive suggestions were made and will be reported back to the sections by the delegates.

Jan 1, 1931

By AIME AIME

TO THE AMERICAN MINING CONGRESS. AMERICAN INSTITUTE OE MINING ENGINEERS. MINING AND METALLURGICAL SOCIETY OF AMERICA. The committee that makes this report was appointed at the meeting of the American Mining Congress, at Denver, Colo., in. November, 1906. The appointment had in view the drafting. of a law for the regulation of quarrying and metalliferous mining under the police laws of the States, with the hope that the uniform adoption of such a law could tend to reduce the number of accidents in mining. Since its. appointment, the committee has had' under serious and continuous consideration the matter with which it was charged. At the meetings 0f the American Mining Congress in 19o7, 1908 and 1909, it reported progress. At the meeting in 1909 it was authorized to present its report not only to the American Mining Congress, but also to the American Institute of Mining Engineers and the. Mining and Metallurgical Society of America, and to present its report in printed form during the interim between meetings of the American Mining Congress. The committee collected from the officials of the States of the Union copies of their mining laws. With the assistance of the Engineering and Mining Journal copies of the laws 0f Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New aland, and certain European countries were also obtained. These laws were subjected to careful study. The first publication of the committee was a summary of the more important metalliferous mining laws 0f this country. Upon the basis of the existing laws of the States of the Union, Great Britain, and the English speaking colonies, a tentative draft. was prepared and printed in limited number in 1909, for convenience in securing the advice and criticism of a considerable number 0f persons engaged in the mining industry. In this way valuable suggestions were received. At the request of the chairman of this committee, Mr. Frederick L. Hoffman, statistician of the Prudential Insurance Company, of Newark, N. J., summarized and reviewed the available statistics of fatalities in metalliferous mining in the United States. Mr. Hoffman's report was published in the Engineering and Mining

Jan 10, 1910

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By Bernard Woolley

The history of the use of calcium aluminates in mining is discussed including a review of very rapid hardening concretes, anchoring using cement capsules and pumped ground control systems. Specific reference is made to the long term performance of highly abrasion resistant orepass lining in South Africa and the use of rapid hardening materials for a range of applications in Australian coal mine where water infiltration creates difficulties or where rapid repair or return to service is required. The topics covered in detail are, high strength abrasion resistant concretes with a 20 year, 30 million ton ore pass life. Rapid reinstatement of wet and worn roadways using mineral dewatering and rapid roadway rebuild solutions, all in I maintenance shift. The different applications are illustrated using examples from operating mines.

Jan 1, 1997

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By Norman A. Grant

"Location and Transportation FacilitiesTHE BEAVERLODGE area of North Saskatchewan is on the north side of lake Athabasca, 500 air miles northeast of Edmonton.The main Eldorado operation and townsite are on the north •side of Beaverlodge lake, which is immediately north of lake Athabasca and is separated from it by only a mile long portage at Lodge bay. The once famous town of Goldfields. Saskatchewan, and the Box property of the Consolidated Mining and Smelting Company of Canada, Limited, are located on lake Athabasca nine mines from Beaverlodge townsite.Previously, all Eldorado freight was delivered by barge at the Lodge Bay portage, hauled across the portage, and across Beaverlodge lake by small Northern Transportation Company barges, which involved many handlings.In 1952 the port of 'Bushell' was established at Black bay. This is a particularly snug harbour, well protected from the main body of the lake and with good foundations for docking facilities. A Butler building, 300 ft. by 60 ft., and tank farms provide storage at the port. A •road from Bushell to the main Beaverlodge operation, a distance of twelve miles through rugged terrain, was built by the Saskatchewan Government. The cost was shared by the Saskatchewan Government, the Federal Government, and Eldorado and other mining companies.Along this road are located the properties of several enterprising mining companies and near the midpoint lies the ambitious budding town of Uranium. This road has made portaging unnecessary and palletized freight loaded at Waterways, Alta., is now loaded directly on trucks at Bushell and delivered to the point of consumption."

Jan 1, 1953

By G. H. Robbins

"Originally presented at TORONTO 94, CIM-AGM, this paper has been updated to reflect the present status of business development for theSO2/AIR process. The paper reviews the back-ground leading to the invention, discusses the process chemistry and historically tracks the commercial development. Engineering and cost considerations are presented.IntroductionThe year 1994 was particularly significant in terms of the technical and business development of the INCO SO2/AIR cyanide destruction process. The year marked a decade of service to the world mining community since INCO acquired the Canadian patent in 1984. In that time period, the technology had become widely recognized as the state-of-the-art process in the field of cyanide detoxification and today we enjoy the distinction of having licensed the process at over 50 project sites worldwide. The application for the process has mostly been in the mining industry in precious metal recovery plants where it offers treatment for a wide range of waste streams such as: CIP/CIL slurries, Merrill-Crowe barren bleed solutions and/or re-pulped filter cakes, tailings pond water recycle or discharge, make-up water to flotation circuits and feed to underground backfill plants. The process also applies to the treatment of high cyanide rinsewaters from metal plating shops. More recently the process is being applied to the rinsing and abandonment of heap leach pads where it has proven to be a very cost-effective application of the INCO process. The distinct advantages that have led to the success of the process are the ability to work on slurries as well as solutions and the significantly low cost of sulphur dioxide products. The process is safe and easy to manage and uses all forms of SO2(liquid, gas or salts) which gives the process tremendous versatility with respect to geographic application. Having more than ten years of service"

Jan 1, 1996

By Michael Rieber

A new mode of coal transportation based on the principles of pneumatic conveying has been recently, proposed by Soo, et al. [5]. Pneumatic transport is not a novel concept and commercial experience with pneumatic pipelines for short haul distances is plentiful. The list of applications is long and includes transporting ores, chemicals and pharmaceutical products, agricultural products, and domestic and industrial wastes. The study by Soo, et al. [5] updated an earlier one [l0] and presented the most recent economic evaluation of pneumatic transportation of coal. Their preliminary study concluded that there are immediate advantages for short-distance transport (less than 100 miles) and that it is both technologically and economically feasible. That study also concludes that pneumatic transport has a higher potential and more promising profitability in long-distance applications than rail if new track and roadbed must be built. Some of the advantages of long and short distance pneumatic pipeline transport of coal compared to rail and slurry transport are: 1) Replacement of diesel fuel consumed by unit trains, as the pipeline can be powered by coal-generated electricity; 2) Reduction of the skilled-labor costs required for upgrading and maintaining railroads; 3) Elimination of signaling, rerouting and overpass costs due to increased rail traffic on' mainline trackage;

Jan 1, 1977

By Lee M. Manna

This report summarizes the program to design, fabricate, install and preliminary test a pneumatic braking system for 10-ton mine haulage cars. Major arrangement drawings are reproduced, pneumatic schematics, parts list and actual developed costs. Recommendations as to system improvements are made.

Jan 1, 1977

By Corwin L. Cooper

This paper, describing; the milling and cyanidation methods and costs at the Yellow Aster gold mine, is one of a series of papers being prepared by the Bureau of Mines on bold milling practices in the United States. Acknowledgments Acknowledgment is made to the executives of the Anglo American Mining Corporation, Ltd., for permission to publish this article, and to A. W. Frolli, manager, and other members of the company staff, for assistance` in preparing the, paper.

Jan 1, 1936

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25·9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24·6 per cent Mn and 23·0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

By Ning Shi

This paper suggests an alternative design approach for an innovative shovel dipper, for use in ground conditions where cutting of virgin ground rather than scooping of blasted material is required. Not only does the new design have an optimized dimension ratio (width:height:depth) and attachment arrangement (angle, position), but also a non-linear pro¯le in 2D and 3D. The approach is based on the simulation of a shovel's duty cycle to verify a pilot dipper model. In order to achieve a realistic simulation that could be used to evaluate a dipper design, the model is e®ectively a descriptor of actual shovel activity under soft ground conditions. The shovel geometry, motion and operation, with an emphasis on digging and dumping kinematics and dynamics are the principal elements of the simulation. The simulation considers a fresh face location, repeating tucking, digging and dumping swing motions within the geometric range of the machine, ending when no more face material remaining within reach without re- positioning. The simulation yields digging force, friction force, trajectory, ¯ll time, ¯ll factor, etc, which may be integrated into two basic considerations: power draw (output) and volume delivered (production), as indicators of dipper performance. The simulation has been used as a tool to modify an existing dipper design, prior to looping further simulation cycles. Ultimately, an optimized or totally-new-concept shape is realized. A prototype dipper as a fractional scale model will be built to verity the performance under actual mining conditions.

May 1, 2004

By H. B. Kinnear

THE first copper stool used under an ingot mold to receive molten steel has recently been taken out of service after it had received ingots amounting to 6012 gross tons. This stool, weighing 8330 lb. had been in continuous service for 1822 heats since its installation. From this modest beginning the use of copper for ingot-mold stools grew to 425,000 lb. in 1934, with an additional 50,000 lb. of copper used in the form of inserts in cast-iron stools. During 1935 the quantity of copper used for stools increased by about 350,000 lb., making a total of 775,000 lb. now in use for that purpose. Copper used for inserts has increased during this time 180,000 lb., or over 350 per cent, to a total of 230,000 lb. The total of copper, therefore, in use at present under ingot molds is slightly over 1.000,000 lb.

Jan 1, 1936