Search Documents

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By Douglas M. Deason

Swelling clays, such as montmorillonite, contribute significantly to the poor dewatering and consolidation behavior of the Florida phosphate clay wastes. Understanding and to a degree, control of the forces which cause the swelling behavior may aid in supplying a solution to this problem. The technical feasibility of utilizing control- led dispersion for aiding dewatering of phosphatic slimes was investigated. This technique is based upon inhibition of swelling and self-dispersing tendencies of the montmorillonite clays by dispersing the solids in electrolyte solutions. Through this process, significant improvements in settling rates and sediment solids content were achieved in both pure clay systems and on simulated phosphate slimes.

Jan 1, 1983

By J E. Askew

The rapid expansion of gold production in Australia over the last five years can be attributed in part to the development of selective mining techniques for open pit gold operations. These techniques allow an increase in head grade with a substantial reduction in mill feed tonnage, as compared with traditional open pit designs. As a result, the capital requirements for mine development and mill construction are substantially reduced, improving the cash flow profile in the early years of operations. To put such a design into effect, the emphasis of mine production must be on producing gold, rather than tonnes of ore. Mine planning at Martha Hill has been based on such a philosophy. After the quantity and grade of the resource had been defined, the exploration programme was increasingly concerned with the local variability of ore zones, and with determining the position of values within broad ore-definition envelopes. The purpose of this work has been to allow the prediction of the tonnages and grades achievable from various levels of the pit when mining selectively using hydraulic excavators. The studies have so far indicated that the Martha Hill deposit can be mined selectively during the early years of production. The additional costs for detailed grade control and a reduced digging efficiency are more than compensated by the exclusion from the mill feed of much valueless material.

Jan 1, 1986

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

By I. T. Oramah

Despite the abundance of solid mineral deposits, Nigeria only earns about 0.5-1% of its current Gross Domestic Product (GDP) from the solid minerals sector. This is as a result of the dominance of the oil and gas industry, which has negatively affected the competitiveness of other sectors of Nigeria’s economy. The dominance of this industry has resulted in unemployment, poverty, hunger, domestic price inflation, corruption, unstable government, and higher exchange rates. These impacts are typical for economies suffering from the effects of "Dutch Disease" and the "Resource Curse". Community-based small-scale mining offers hope as an economic activity that can create wealth, employment, reduce hunger and poverty, and provide basic amenities for rural communities with solid minerals endowment. This study presents preliminary results of ongoing research into the prospects of using community-based small-scale mining in a developing country like Nigeria to move towards rural sustainable development.

Jan 1, 2011

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

The war story of the engineer corps at home and in France is told officially for the first time in the advance sheets of the War Department's brief history of American war efforts. Many of these accomplishments have been published before as isolated incidents, but they gave no idea of the extraordinary duties modern warfare has laid upon engineering troops. In the engineering units that reached the other side, there were seven regiments and two battalions of railway construction engineers; five battalions for maintenance of way; two battalions for maintenance of railway equipment; four regiments and one battalion to operate the main American railways in France; three regiments to operate light railways and their repair shops; two regiments to operate the regular railway repair shops; two regiments and six separate battalions on general construction work; two regiments for storing and transporting engineer supplies; a forestry regiment; a light-railway construction regiment; a roadbuilding regiment; a water-supply regiment; a mining regiment; a quarrying regiment; a technical regiment for surveying and sound ranging; three survey and printing battalions; two railway transportation battalions; an electrical and mechanical regiment; several separate companies to operate cranes; a camouflage service; five inland waterway companies, to operate canal boats and the like; five pontoon trains and a pontoon

Jan 6, 1919

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By R. L. Hills

America's industry uses about 44% of the total energy consumed by the nation directly as fuel burned in industrial plants or indirectly as fuel burned by utilities to provide electric power. In addition, industry requires raw materials or feed stocks derived from fuel sources or having fuel value. This represents about 11% of total U. S. energy consumption, bringing industry's portion to about 55%. Adding that portion of energy consumption required by the transportation sector to move raw materials, intermediates, and finished products, the total energy impact of industry approaches 213 of total U. S. consumption. It is obvious that American industry has the largest share in the task of balancing energy demand and supply. What are we going to do? -- We must increase the supply of energy and increase the beneficial results obtained from each unit expended. Both avenues, unfortunately, are limited in extent and speed. Increases in supply cannot occur without drastic and permanent increases in cost. These increases in cost are un- desirable and inflationary but do provide incentive for the rational businessman to expend the effort and money required to improve the effectiveness of energy in industry.

Jan 1, 1975

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By G J. Corbett, T M. Leach

Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of youngerPacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By W. Leblanc, J. C. Marsh, D. Kettle, J. Tompkins, G. Hartley

"The Lingan Mine is the newest of the four operating collieries of the Cape Breton Development Corporation and is located on the east coast of Cape Breton Island. Development of slopes began in 1969 using four Dosco Roadheaders. Production commenced in October 1972, when a partial extraction section utilizing a continuous miner, loader and shuttle car was installed. A second Joy unit is scheduled to begin production early in 1973. This paper describes the production and development operations, the ventilation system and the equipment in use at the mine."

Jan 1, 1973

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By P. S. Arthur

The copper I SAS MELT? process is a submerged lance bath smelting technology. In the 20 years since the process was first demonstrated on a semicommercial scale at Mount Isa in north-west Queensland, Australia, copper ISASMELT? plants have been constructed to treat concentrates or secondary raw materials around the world. The process is operating in smelters in Australia, the USA, Belgium, India, Germany, China and Zambia. ISASMELT? plants have been installed to improve the environmental performance of operating smelters and reduce costs for smelting companies. A new copper furnace is being commissioned at Southern Peru Copper Corporation in early 2007, while more furnaces are under design for installation in Kazakhstan and Peru. Copper ISASMEL T? plants are supplied as complete technology packages including engineering design services for the furnace and key ancillaries, supply of core equipment, provision of intensive training programs in operating plant environments and commissioning assistance services. The proven technology transfer process ensures successful implementation of submerged lance bath smelting into large scale plants. This paper summarises developments at recently constructed copper ISASMELT? plants.

Jan 1, 2007

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By Franz Albert Nonnen

Backfill systems have been used for as long as mining activities have existed. Various backfill methods have been developed over the centuries with consideration for geological necessities, the technical means available, security requirements, and available finances. In the past, backfill systems were introduced and upgraded geographically in accordance with local experiences. In modern times, mining engineers participate in international forums for the exchange of knowledge so that backfill techniques and experiences are shared concurrently in mining areas all over the world. Mine backfilling increases the cost of mining so that great attention must be paid to choose a low-cost, reliable, and low maintenance backfill system. Some methods are described in this paper.

Jan 1, 2001

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983