Search Documents

By K. G. Stowe

"1. Introduction Mattagami Lake Mines and Orchan Mines operate zinc copper mines adjacent to one another near Matagami, Quebec, situated approximately 300 kilometres north-east of Rouyn-Noranda. (Note: Mattagami Lake and Orchan are in the process of being absorbed by Noranda Mines and will become Noranda Mines-Matagami Division). Both concentrators began operations in late 1963.The Mattagami Lake concentrator is capable of treating up to 3,500 metric tons per day of massive sulphide ore with a mineral composition shown in TABLE 1. The Orchan concentrator consists of two separate circuits - the Orchan circuit with a capacity of 1,050 metric tons per day and a custom circuit with a capacity of 825 metric tons per day. Throughout its operation, Orchan has custom milled ore from several smaller deposits in the Matagami district."

Jan 1, 1979

By J Steyn

Block Cave mining is one method used to extract ore from underground diamond mines as well as other massive orebodies such as copper. This necessitates the excavation of many kilometers of tunnel within the ore body. The integrity of these excavations needs to be maintained over a number of years. Most Kimberlites and weak orebodies are extremely susceptible to degradation when exposed to moisture and the atmosphere. It is therefore essential that some form of weathering protection is applied as soon as possible after exposure. Conventional methods of weathering protection such as shotcrete do not easily fit in with the production schedule, hence the need for a more efficient system that could be applied immediately after exposure and serve as a temporary support or even as a permanent support medium. The main advantages of thin sprayed liners (TSL) compared to shotcrete are the ease of application, speed of application, early strength, much reduced transportation of material, less labour intensive and cost effectiveness. Several Thin Sprayed Liners suitable for various mining environments and geotechnical conditions are available and could be well suited as additional support the undercut level development in a block cave where this may be required. TSL offer a cost effective support solution as an alternative to shotcrete in areas where the building of a support structure is not a requirement.

Jan 1, 2008

By A. Chagnes

This paper presents a modelling tool that can be used to predict the behaviour of solvent extraction processes. In particular, this model allows calculating metal extraction efficiency as a function of pH, solvent flowrate, stripping flowrate and aqueous feed flowrate in the mixers-settlers. This model is applied to the recovery of cobalt from acidic chloride media by using CYANEX® 272 as extractant diluted in kerosene. Keywords: Cobalt, mixer-settler, modelling, solvent extraction

Jan 1, 2020

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By E. J. Schmitz

The mining of the Triassic coals of the Richmond basin has been carried on, upon a larger or smaller scale, for more than a hundred years. Notwithstanding the close proximity of the field to a large city and to tide-water, assuring both a good home-market and cheap transportation, and notwithstanding the good quality of the fuel and the great thickness of the principal bed developed and worked, operations in this field have been conducted with but limited success. The basin comprises about 189 square miles, being from 24 to 31½ miles in length by 5½ to 10 miles in width. Not much more than one-tenth of this area has been explored in a practical and efficient way, and not over 1200 acres have been worked near and along the outcrops or edges of the coal. The practical mistakes which have been committed undoubtedly in a number of the mine-operations of the past, do not alone explain the unsatisfactory success and progress of the industry of this field ; nor can it be ascribed to the lack of local enterprise. Other reasons have to be looked for; and, as a principal one, the irregularity and the faulted conditions of the coal deposits must be pointed out. As a second cause, the indifference of the State government, which leaves the development of the field entirely to private enterprise, instead of aiding it by systematical and practical geological investigations, deserves to be mentioned. Nothing has been done by the State since the excellent work done more than fifty years ago by Professor Rogers, who could not at that time enter into the details of such

Jan 1, 1895

By Eugene Frey

"INTRODUCTION The Iron Mountain deposits were examined in the summer of 1943 by engineers of the Bureau of Lanes, and a diamond-drilling project was set up under the Strategic Minerals Program. Actual drilling operations, under the supervision of a Bureau engineer, commenced November 9, 1943, and were completed on November 1, 1944. When the Bureau began detailed exploration of the Iron Mountain deposits, the Federal Geological Survey participated. Dr. I. W. Newhouse, of the Survey, and Dr. A. F. Hagner, of the Wyoming Geological Survey, were assigned to the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, acknowledgment is made to S. R. Zirrmerley and F. T. Allsman, Bureau of Mines, Salt Lake City, Utah, who supervised the work of this project."

Nov 1, 1946

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010

By Michael R. Cartwright

The Gold Acres outcrop was located by Lee Lakin in 1922, according to Mr. H. W. Treweek. There was no activity, however, until 1935, when prospect drifts and pits penetrated the deposit. It was then drilled by the Willow Creek Mining Company. Beginning in the late 1930s and continuing to the late 1940s more than 150 churn drill holes were drilled in the Gold Acres area. From this drilling came what is now known as the London Extension pit. Only oxidized ore amenable to cyanide vat leaching was mined during this time. Our records indicated that this period of mining removed some 1.4 Mt (1.5 million st) of ore at an average grade of 0.006 kg/ t (0.2 oz per st). Union Pacific and Newmont Mining Company worked in the area prior to acquisition by the Cortez Joint Venture. Union Pacific drilled a number of core holes in the area. The unoxidized nature of the ore, small tonnage, and low grade undoubtedly prevented mining at this time. From these indications of mineralization shown by previous companies, the Cortez Joint Venture developed and mined 2 Mt (2.4 million st) at 0.005 kg/t (0.15 oz per st) in the Gold Acres pit. This pit is located immediately southwest of the older London Extension pit. Cortez Gold Mines has continued to drill to the west and south of these pits along the downdip continuation of the former ore bodies. The downdip extension is unoxidized and more metallurgically difficult than the normal Carlin type ores, but, more than 2.4 Mt (2.7 million st) have been outlined. It depends now upon the gold price and milling costs to turn this mineralized area into an ore body. A possible lesson to be learned from this deposit is that continued mining success depends upon an ongoing adequately funded exploration-development-metallurgical research program. These three disciplines must always be present to locate the mineralization and to turn this mineralization into ore. [ ]

Jan 1, 1985

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

By Kanaya Koichiro

Doyashiki Concentrator in Hanaoka mine of Dowa Mining Co., Ltd. started the operation in 1943, treating the ore mainly from Doyashiki ore deposits. After the cessation of mining of Doyashiki ore body in 1973, Doyashiki concentrator began to treat the ore from Fukazawa mine instead in the same year, and furthermore the ore from Ezuri mine In 1979. Currently Doyashiki concentrator treats 30,000 tons of ore per month from both mines. The ore treated is complex sulfide ore, called "Kuroko" (black ore), and the principal minerals contained in the ore are chalcopyrite, galena, sphalerite, pyrite, and barite, accompanied by bornite, tetrahedrite, tennantite, covellite, stromeyerite, argentite, polybasite, pearcite, and electrum. The Principal gangue minerals are quartz, gypsum and clay. The grade of the feed to the concentrator averages 0.9 p/t Au, 110 g/t Ag, 1.1 %Cu, 2.8 %Pb, 9.2 %Zn, 5.0 % Pyrite-S and 13% BaS04. The feed is, after washing and two-stage crushing, ground to 88% minus 200 mesh in a rod mill and ball mills with cyclone classifiers, and five concentrates are recovered by flotation. Primarily copper-lead bulk concentrate is recovered by sulfurous acid-lime flotation method, and then from the bulk concentrate copper concentrate is floated by hot pulp flotation method, sinks being lead concentrate. Zinc concentrate is recovered from the tailing of copper-lead bulk flotation, pyrite concentrate from zinc flotation tailing and barite concentrate from pyrite flotation tailing. The final tailing is sent to the dam.

Jan 1, 1982

Jan 1, 1970

By V. Yahorava

Ion exchange is considered to be an effective technology for the removal of various impurities from cobalt advance electrolytes. With the correct choice of resin, ion exchange can consistently remove the required impurities to the levels for the production of high-grade cobalt metal. Although ion exchange was in the past used primarily for nickel removal, more recently it has been also considered for the removal of copper, zinc, and cadmium. Generally, granular ion exchange products are used, but Mintek is currently evaluating ion exchange fibres for a number of applications, including the removal of copper from cobalt advance electrolytes. Fibrous ion exchangers have major advantages compared to granular resins in that they have significantly higher reaction rates, and wash water volumes could be limited. Granular and fibrous ion exchangers were evaluated and compared for the removal of copper from cobalt advance electrolyte. A synthetic electrolyte containing 50 g/L cobalt and 50 mg/L copper was used for the test work. Equilibrium isotherms, mini-column tests, and split elution tests were done. The results were used to size a full-scale operation to treat 100 m3/h of electrolyte. The potential cobalt losses or recycle requirements were estimated, and data to calculate indicative operating costs for each adsorbent was generated. This information was used for a techno-economic comparison of granular and fibrous ion exchange systems for the removal of copper from cobalt advance electrolyte.

Jan 1, 2014

By L. H. McGuire

Many coal beds in the State of Washington, pitching as much as 90°, offer unusual mining conditions. This paper describes methods and safe practices of mechanized mining in pitching bituminous-coal beds that have attracted the attention of mining people from most of the coal-producing countries of the world. The development and use of continuous miners as part of the mechanized program apply particularly to the Roslyn-Cle Elum coalfield, Kittitas County, Wash. All three mines now operating in the field use continuous miners and during 1957 furnished 72 percent of the State's total coal production. Mining operations are now conducted in three coal beds of the Roslyn-Cle Elum field. The coal measures range from 3-1/2 to 20 feet in thickness and vary in dip from 5° to 45° in the localities where the coal is mined. Some safety measures adopted by-the principal operating company in the field during the past 30 years of mechanized mining follow: Use of only permissible electrical or compressed-air-operated equipment on other than intake air; providing and using an explosion gallery to test repaired permissible electrical equipment before taking it underground; use of only compressed-air-operated drill augers in preference to permissible

Jan 1, 1959

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

The extent to which man's activities are influencing the earth's climate is subject to considerable debate. Internationally however, this debate has been put aside somewhat by the Kyoto Protocol. This international agreement is the political response to the threat of Global warming, predicated on the precautionary principle.NZ is seeking to be a leader in the Kyoto Protocol. Given our unique GHG emission profile and the structure of our economy, and the major uncertainties in both the science of climate change and the Kyoto Protocol itself, this desire to lead is absolutely inappropriate in this instance. We face a different, and often more severe, set of challenges in an economy that prices C emissions than virtually all of our trading partners. Unfortunately, these differences have not been reflected in climate change policy development to date. This represents a major threat to New Zealand's economy, wealth and jobs, particularly in the sectors that have been the core drivers of our economy over the last 20 years or so - agriculture, energy, primary processing. We do not, and should not, seek to avoid the issue but we must protect our economy and move with or follow our trading partners and competitors, not lead them.

Jan 1, 2002