Search Documents

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By Zeljka Pokrajcic

Crushing and grinding, or comminution, circuits are the most energy intensive process of a mineral processing plant. Comminution involves the physical size reduction of an orebody to a particle size sufficient for recovery of the mineral values. However, the comminution process remains inherently inefficient. The inefficiency is a result of the operating nature of comminution devices such as grinding mills, where transfer of energy between grinding media and particles in unconstrained and completely random. New comminution circuit design strategies are presented in this paper. The aim of the new strategies is to improve the overall efficiency of the comminution process and reduce the total energy consumption of a comminution circuit. The energy efficient strategies include the: ? rejection of coarse size liberated gangue from the comminution circuit and further downstream size reduction ? use of more efficient grinding and crushing equipment ? the selection of coarser particle product sizes to alleviate the increased energy intensity required to achieve finer product sizes Singularly and when combined, these energy efficient strategies can significantly decrease the overall energy consumption of a comminution circuit. This paper also explores the financial impact of certain energy efficient strategies using an analysis tool called EcoNomics?. It shows that substantial financial gains can be made by including more efficient technologies and methods in comminution circuit design.

Jan 1, 2010

By Sabina Brady

Nearly a decade and a half after the US and China established formal diplomatic relations, and two decades after the two countries signed the Shanghai Communique and established commercial ties, the world, and perhaps China itself, has discovered that a wealth of natural mineral and energy resources lie beneath China's soil and directly off its coast. The country's coal reserves and oil and gas potential are well known. Its ferrous and nonferrous metal reserves are respectable and in a number of instances pre-eminent. According to 1981 Minerals Yearbook estimates - more often than not below those now being claimed by China - the country's aluminous metal reserves are about 907 Mt (1 billion st); iron ore reserves are 40 Gt (44 billion st); and copper reserves are about 46 Mt (54.4 million st) of contained metal. In addition, the country has about 10.7 Gt (11.8 billion st) of phosphate reserves, the fourth largest in the world, and 3 Gt (3.3 billion st) of pyrite. China's national Sixth Five Year Plan promulgated in late 1982 ended a stringent three-year retrenchment or readjustment period in which a number of major development projects involving foreign participation initiated in the late 1970s were shelved. The new Five Year Plan is a signal both within and outside of China that things are now moving again, and that major industrial and service sectors are receiving the kind of funding and flexibility they need for expansion, construction and modernization. The new plan's strategy for growth is measured and much less grandiose and frenetic than it was five years ago when China flung open its doors to foreign companies and invited participation in large-scale development projects. Now, the country's reticence to spend foreign exchange to purchase key equipment, technology, and services -a reaction to these projects and the spending they entailed - is clearly on the wane. In China's effort to quadruple its GNP by the year 2000, there is a new willingness to use some of its substantial foreign reserves. In fact, it is projected that 1983 will witness a $1.9 billion deficit, with a $2-3 billion deficit in 1984 and 1985. The following article discusses implications the Sixth Five-Year Plan has for nonferrous metal development in China. It is the first in a series of three articles on Chinese mineral resource development to be published in Mining Engineering over the next few months. The second article will identify specific nonferrous projects underway, while the third in the series will focus on trade and development opportunities for phosphate and potash producers in China. China's Ambitious Plans In the last few months, the exploitation of China's nonferrous resources and development of its industrial processing capabilities have begun to receive increasing attention on both provincial and central levels. Unlike the earlier modernization drive of 1978 when China's ferrous sector - best typified in the Baoshan iron and steel project - got the lion's share of the Ministry of Metallurgical Industry's (MMI) energy and resources, it now appears that in some respects the nonferrous and industrial sectors are finally moving out from beneath the dominating shadow of ferrous and getting their own day in the sun. Separation of Nonferrous from Ferrous One clear demonstration of this is the establishment in April 1983 of the China Nonferrous Metals Industry Corporation (CNFMIC). The corporation is composed of 819 enterprises with over a million workers, and also includes 12 nonferrous metal construction companies, eight design institutes, and three prospecting companies. Of ministerial rank, CNFMIC is responsible for the development of both the country's nonferrous resources and its processing facilities. Although closely tied to the parent ministry from which it sprang (i.e. MMI), CNFMIC, at least theoretically, is separate and independent from it. One strong indication that this independence is, or soon will become a reality, can be seen from the fact that the new corporation is not headed by the former MMI officials, not even those who made up the ministry's now defunct nonferrous bureau. Instead, its president Qiu Chunfu is formerly of the State Economic Commission and the China International Trust and Investment Corp. Its general manager Fei Ziwen, an engineer in his early 50s, is from the Jiangxi Province Copper Corp. The new nonferrous corporation appears to be powerful

Jan 7, 1983

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By Georgios Bartzas, Vasiliki Karmali, Konstantinos Komnitsas, Anna Kritikaki, Dimitra Vathi, Stylianos Tampouris, Arne Peys

Large volumes of slags, with varying mineralogical and geochemical characteristics, are produced annually by the ferrous and nonferrous metallurgical industry. Most of them are considered as potential secondary resources and may be valorized, following the principles of circular economy, for the recovery of critical elements, including energy transition metals. Apart from the economic benefits, valorization of slags may contribute to the competitiveness of the metal industry and the conservation of natural resources. Valorization also results in minimization of environmental impacts on soils and waters in slag disposal areas, due to the prevention of solubilization and subsequent migration of potentially hazardous elements. The present study utilizes ferronickel (FeNi) slag for the production of alkali-activated materials. The effects of the main experimental parameters, including sodium hydroxide (NaOH) molarity, silica/sodium oxide (SiO2 /Na2O) molar ratio in the activating solution, precuring and curing time, curing temperature and aging period on several properties of the final products, are assessed.

Apr 1, 2025

By Kun Li, Shuaishua Yue, Huigui Li, Yuan Ruifu, Yongxiang Xu, Huamin Li

"Coal seams in Tashan Mine of Datong Coal Group in China average 49.2 ft (15m) thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 12.5 ft (3.8m) and the top coal caving height was 36.7 ft (11.2m). The gateroad pillar between panels was 124.6 ft (38m). During retreat mining, serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore, pillarless mining was experimented.Using numerical modeling and comparative study of cases of similar mining condition, it was decided to employ a 19.7 ft (6m) wide pillar, rather than the previous 124.6 ft (38m) wide pillar. Support system for the gateroads was designed and implemented. During gateroad development, pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion.Since the development of gateroad has just completed, and retreat mining has not begun, the effectiveness of the proposed methods is unknown at this point. However, monitoring will continue until after mining. The results will be published in a separate paper.INTRODUCTIONGeneral descriptionTashan mine is located about 15 Km south of the city of Datong, Shanxi province, China (aure 1). The 2014 raw coal production was 25 million mt."

Jan 1, 2015

By K. S. Raja, B. McNall, B. Pesic

"High-level radioactive wastes are stored in large underground storage tanks made of low-carbon steel. The wastes consist of concentrated solutions of sodium nitrate (NaNO3) and sodium hydroxide (NaOH), and the radionuclides 137Cs, 99Tc, and 90Sr. The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV), which in turn modifies the kinetics of corrosion of the storage tank. To understand the influence of technetate ions on the corrosion of steel, electrochemical polarization studies of A 537 steel samples were carried out in 1 M NaNO3 + 0 .05 M S r(NO3)2 + 0.1 M NaOH with and without addition of HReO4 at different temperatures (24 – 85 °C). The concentration of HReO4 was varied from 0.014 – 0.04 M.INTRODUCTIONAqueous processing of spent nuclear materials generates a large amount of high-level radioactive wastes. The wastes are primarily salt solutions of sodium hydroxide and sodium nitrate which also contain fission products such as 137Cs, 99Tc, and 90Sr. Among the high level radioactive fission products, Tc-99 is of great importance because of its high concentration, long half-life (2.1 x 105 years), high solubility in geologic waters as technetate, and rapid diffusivity through the geologic systems. The solubility of technetate ions varies depending on the oxidizing conditions prevailing in the storage containers. High level radioactive wastes are stored in single shell or double shell tanks made of low carbon steels such as ASTM type A15, A516-70 and A537. Most of the available literature on corrosion of steel in simulated radio active waste environments pertains to nitrate induced stress corrosion cracking (Subramanian & Mickalonis, 2005). The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV). Corrosion of steel and formation of Fe(II) and Fe(III) will affect adsorption and reduction of Tc species. The radioactive species can irreversibly be sorbed on the steel surface by oxidation of Fe(II) to more stable Fe(III) and fixed as less soluble Tc(IV)/Fe(III). The solubility of Tc species is also affected by other factors such as dissolved oxygen, local pH, temperature etc. How the corrosion behavior of steel will be affected in the presence of Tc species is not clearly understood.Cartledge (Cartledge, 1960) demonstrated that passivation of iron can be achieved in the presence of oxygen along with suitable inhibitor ions/molecules of the general formula XO4 n-, such as pertechnetate (TcO4 -). The pertechnetate ion is univalent. Since it is derived from a strong acid, no buffering action can be expected from this ion. The redox potential of the reaction (1) is 0.738 VSHE (Pourbaix, 1974)."

Jan 1, 2012

While coal occurs beneath about 18 percent of Utah, only 4 percent of the state has minable reserves. Utah's coal fields are mostly bituminous. Current coal production in Utah is largely by underground mining, making Utah unique among the coal-producing states. Most coal seams are more than 8 feet thick. Utah's coal resources are about 6.3 billion tons, 1.3 percent of the national reserve. Most of Utah's coal resources are held by the Federal Government and Indian tribes and are mined under lease. The climate of the Utah coal region is characterized by hot, dry summers and cold, relatively moist winters. Normal precipition varies from 6 inches in the lower valleys to more than 40 inches on some high plateaus. The growing season ranges from 5 months in some valleys to less than 3 months in mountainous regions. These extreme climatic conditions make reclamation difficult. Utah gained primacy when its regulatory program was conditionally approved January 21, 1981. Full program approval was obtained March 7, 1983. The Abandoned Mine Land Program was approved June 3,1983. A Federal Lands Cooperative Agreement was signed in March 1987; Utah performs all enforcement activities and some permitting activities on federal lands.

Jan 1, 1992

By Brian Gar Wingfield

Bulk explosive systems have developed from the infancy stages in the early sixties to a sophisticated process of the nineties. With ever changing bulk explosives technology, bulk delivery and loading systems needed to keep pace. Efficiency, as compared with packaged loading, was the keyword allowing faster loading of trucks and shots. Efficiency was also improved by the explosives coupling factor that bulk loading permitted.

Jan 1, 1991

The structure and tectonic setting has had a strong influence on gold mineralisation at the Porgera gold deposit. Here, the structural controls on the mineralisation at Porgera are discussed and placed in a regional tectonic context. The Porgera gold deposit is related to the emplacement of the Porgera Intrusive Complex. Prior to intrusive emplacement at Porgera,Papua New Guinea was affected by a major fold and thrust episode which occurred in response to arc-continent collision in the Late Miocene. After crustal shortening the region experienced a relaxation of compression which is expressed in the deformation accompanying mineralisation at Porgera. The first stage of mineralisation (stage I) is hosted by extension fractures, and is spatially associated with exposed intrusive stocks. A later episode of mineralisation (stage II) is hosted by the faults and fractures of the Roamane Fault Zone, which was active as a dip-slip normal fault during stage II mineralisation. Therefore a change in the tectonic environment from shortening to extensional tectonics can be seen at Porgera before and during mineralisation. Rapid fault-slip during stage II mineralisation may have aided high-grade gold mineralisation by subjecting hydrothermal fluids to changes in pressure, temperature, fluid-fluid and fluid-rock interaction. Uplift to form the highlands of Papua New Guinea occurred after mineralisation and was largely complete by 4.0 Ma.

Jan 1, 1995

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By Leroy O. Gieseke, John B. Begley

If the particles produced and transported in your plant are as chunky as rough crushed coal or as fine as cement, there are probably several conveying and elevating systems suitable for your operation. The problem is deciding which is most suitable in terms of space, energy cost, allowable product degradation, productivity, and angle of movement. Each conveying and elevating method should be fit to the products it can handle successfully, to desirable economics, and to suitability for the overall operating scheme. Matching along these lines will result in selection guides that should be useful for many years, although design evolution is expected for the materials handling equipment involved. There are several common bulk material handling devices for moving solids: belt conveyors, screw conveyors, bucket elevators, chain conveyors, and en-masse conveyors/ elevators. En-masse conveyor/elevator equipment is commonly compared and contrasted with the other devices. These comparisons often involve en-masse versus all others. En-masse has developed into a versatile technique because the machines can move materials horizontally, vertically, or in closed circuit. Such machines unload, elevate, store, reclaim, and distribute materials-all without ancillary equipment except for chutes and gates. Bulk material can be carried, as with a belt conveyor or bucket elevator; pushed, as with a flight or screw conveyor; bumped, as with a vibrating conveyor; blown, as with a pneumatic conveyor; fluidized, as with a dense phase pneumatic conveyor; or by applying internal forces to it to induce "en-masse" flow. Conveying en-masse is analogous to the flow of a fluid in an open channel, and elevating en-masse is analogous to the flow of fluid in a pipe. In the case of a fluid, flow is caused by a differential in pressure. With en-masse movement, flow results from resistance to shear induced by the movement of chain and flights.

Jan 12, 1980

By Z. Sun

Magnetic fields have been used for inclusions removal from melt and preparation of materials with gradient compositions. Fundamental in these applications is that the induced magnetic forces on the particles/melt can enhance migration and change the interaction behavior. In the present paper, migration and interaction behavior of electrical-insulating particles in a conductive melt under strong magnetic field are theoretically analyzed. It is found that the migration can be considerably enhanced for micrometer sized particles by applying a strong magnetic field. In addition, two forces are involved in the interaction between two particles: the interparticle magnetic dipole-dipole attractive force due to magnetization and the repulsive force induced by flow of the melt. This theoretical analysis renders a better understanding of recent experimental results. Additionally, a new method by using strong magnetic field can be proposed to control the particle size distribution for the preparation of metal-matrix composites.

Jan 1, 2009

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change.   The aims of this paper are to: +        outline alternative types of mining contracts, as well as their strengths and pitfalls; +        describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +        identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007

By Jerry C. Tien

Without a doubt, the scope of China?s coal boom has been nonstop. Despite the world economic slowdown, China?s year-on-year gross domestic product (GDP) jumped 10.3 percent year-on-year in 2010, boosted by a faster than expected 9.8 percent expansion in the fourth [ ] quarter. And, the first quarter of 2011 expanded another 9.7 percent. According to a frequently cited statistic, the country is building two mid-sized coal plants each week. This amounts to a yearly increase equivalent to the entire power grid in the United Kingdom. China?s coal production was doubled in the last 10 years, from 1.044 Gt (1.15 billion st) in 1999 to 3.2 Gt (3.52 billion st) in 2010. This is 3.2 times the U.S. production (986 Mt or 1.085 billion st) and nearly half (46.3 percent) of the world?s total coal production (6.91 Gt or 7.6 billion st). This rapid increase of demand for coal has made China the world?s largest coal importer in 2009. With the economic situation improving, this trend is expected to continue.

Jan 1, 2011

Jan 1, 1970

By D. Harrington

"Coal—mine explosions are accidents that can and should be prevented. In former years hundreds of lives were lost each year in the United States as a result of such explosions, but after 1932 the numerous precautionary measures adopted had reduced their frequency and severity 75 percent or more until in 1940 several very disastrous explosions marred the good record. Unfortunately, both the number and severity of explosions seem to be tending to increase compared with the relatively good achievement from 1933 to 1940. The requisites for an explosion are ever present in all soft-coal and many hard-coal mines. A certain combination of circumstances, such as a flame or an arc in a cloud of dust or in a body of gas or both may start an explosion at any time. The fact that the frequency and severity of explosions were lowered for 6 or 7 years is no guarantee that such freedom from explosions will continue, as the bad record of 1940 has shown, and underground workers should feel honor bound to exercise the utmost care so that they will not help to bring about the circumstances that will cause an explosion.Although mine operators bear the main responsibility for preventing explosions, miners can do many things to help. As about 9 out of 10 explosions begin at a working face, it is largely within the power of workers to prevent them. All miners should do their part willingly and should not defend a fellow workman from punishment, even from discharge, for disobeying necessary rules, whose disregard may cause the death not only of the safety-rule breaker but also of many of his coworkers.When a miner is careless and is injured some other way than by an explosion he may be the only one to suffer, but if his carelessness causes an explosion he not only endangers his own life but also that of every other man in the mine and possibly the lives of persons outside the mine.Experiments have shown that ignition of as small a quantity as 150 cubic feet of an explosive mixture of methane and air under certain circumstances can start an explosion that will traverse an entire mine. Thus, ignition of an explosive mixture of gas 1 foot down from the roof and 13 feet back from the face of a 12-foot entry might cause a widespread explosion if the right quantity and kind of dust were present. Many persons have ignited much larger quantities of gas without being killed, but they survived only because dust, confinement, and other conditions were not exactly ""right."""

Nov 1, 1940

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997