Search Documents

By C. T. Aimone-Martin, B. M. Meins

This paper compares response of large urban structures to small charge weight, ultra-high frequency rock blast excitation from contiguous excavation to that of houses to more distant, larger charge weight blasts. Time correlated responses were measured for both structures at the corners, top and bottom of the structures as well as in the foundation rock below the bottom. The comparison allowed the following conclusions: Close-in blasting with direct rock to building wave transmission imposes short wave length excitation which fails to excite the large, massive structures synchronously whereas the more distant blasts do synchronously excite houses. The larger urban structures respond predominantly in wave transmission mode where there is a noticeable difference in time, frequency, phase and amplitude of motions measured at the bottom and top corners of the structure. Excitation motions along the base of the larger urban structures also differs in time, frequency, phase and ampli-tude. The short wave length of the excitation motions leads to attenuation of the peak particle veloc-ity along the base. Ultra-high excitation frequencies, which are much higher than the expected struc-tural natural frequencies, lead to deamplification for all events for the large urban structures.

Jan 1, 2018

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By T. J. McKeon

Partition curves are used to evaluate the separation performance of gravity-based concentrators. The partition curve is used to identify the nominal density cutpoint and relative sharpness of the separation. In addition, the graphical representation makes it possible to quickly identify the root cause of misplacement based on the characteristic shape of the partition curve. Partition curves have been traditionally constructed using data obtained from float-sink tests using heavy organic liquids. These toxic liquids are environmentally unfriendly and have been banned in several countries. Another method of establishing the partition curve is to introduce density tracers into the feed and plot the distribution to the lights and heavies. For heavy mineral separations, this approach is generally impractical due to the fine particle size. In addition, the partition data obtained using these existing techniques do not account for secondary factors such as particle shape that may influence the separation. In light of these problems, a methodology was developed for constructing partition curves using experimental data obtained from microscopic grain-counts. This technique, which essentially uses the different mineral species as density tracers, provides a powerful tool for evaluating heavy mineral separations. A case study is provided to demonstrate how this analytical approach can be used to assess and improve the separaton performance in an industrial upgrade plant.

Jan 1, 2005

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Amin Saravari, Jamal Jafari, Abbas Sam

"The fourth concentrate production plant includes the comminution systems and the medium-low intensity magnetic separators (LIMS). Based on different conditions, two types of materials are fed into the plant. Type A: 70% of mine ore and 30% of reject materials from magnetite plant and type B: 100% of mine ore. The goal of the present study was to increase the iron grade and the blain number with low sulfur content in final concentrate as the pellet feed. An appropriate pellet feed should have more than 67% of iron, less than 0.1% of sulfur and a Blain number of more than 1800 cm2/g. The Fe, S and Blain no. amounts for the present concentrate are 66.6%, 0.95%, and 500 cm2/g (feed type:A) and 67.8%, 2.3%, and 450 cm2/g (feed type: B), respectively. In this research, the plant improvement efficiency was evaluated by changing the feed particle size distribution and using the flotation system. Laboratory experiments were designed based on the three circuits:1) LIMS (Low Intensity Grinding Rolls) feed grinding-LIMS test-flotation test2) LIMS feed grinding-flotation test-LIMS test3) LIMS concentrate grinding-flotation testThe best results were obtained using the first circuit at the LIMS feed size (d80) of 132 ?m. The processing results using the circuit no. 1 (feed type: A), showed a LIMS concentrate with 69.8% of Fe and 0.36% of sulfur. In this case, the final concentrate (after flotation) with Fe grade of 70.3%, sulfur content of 0.07% and Blain no. of 1571 cm2/g were obtained. In case of the feed type of B, the LIMS concentrate with Fe grade of 68.7%, and sulfur grade of 1.6% was achieved. Also, the Fe and sulfur contents were 69.3%, and 0.4% respectively with a Blain number of 1112 cm2/g. According to the obtained results, it was suggested that a LIMS feed comminution along with a LIMS and flotation systems are necessary to achieve an appropriate iron and sulfur grades with an acceptable blain number. To reach a concentrate Blain number as a pelletizing feed, a High Pressure Grinding Rolls (HPGR) system at the end of the processing line was recommended."

Jan 1, 2016

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By A. Noël, R. Lapierre, M. Provencher

"Modem aluminum smelters are facing significant operating cost pressure. Key methods used by smelters to manage this pressure are automation and production-information systems to optimize processes, manage quality, anticipate problems and reduce operating costs. In 2002, Aluminerie Alouette Inc. began its Phase II Expansion project, and retained the joint venture of SNC-Lavalin and Hatch (SLH) as its engineering, procurement and construction management (EPCM) team. Alouette had the distinction of being one of the most efficient aluminum smelters in the world. Alouette already understood the importance of systems integration in project delivery. For Phase II, key objectives were identified to ensure ""a state of the art"" integrated architecture that would support Alouette's production goals to integrate the existing facilities with the expansion, to form a single efficient facility and meet project schedule and budget targets. Achieving those objectives within the context of a large project often creates major challenges due to the nature of the traditional EPCM delivery model, which relies on several vendors and third-party-systems integrators. In this case, an integrated Alouette-SLH team was made responsible for all aspects of the systems integration, taking over the task from most suppliers. The integrated team was responsible for delivering an automation system and plant-wide-production IT system for the new facilities while accommodating migration for the existing systems. Through the use of rigorous methodology and advanced state of the art technology, the IT and automation strategy led to significant value creation and is recognized today as one of the key factors of the project's success. The primary results were: fast and efficient start-up of facilities, due to quality programming and implementation; a plant able to operate as a single entity; automation and IT systems delivered before time and under budget; standard programming methods implemented throughout the plant; and reduced and simplified maintenance."

Jan 1, 2006

By Jared Winkler, Jon A. Hummer, Aleksandar D. Bugarski, Shad Peters, Steven E. Mischler, Steve Cochrane, Shawn Vanderslice, Teresa Barone

The case study assessed submicron aerosols at a continuous miner (CM) section, diesel aerosol concentrations at the longwall (LW) section, and elemental carbon (EC) and total carbon (TC) exposures. Aerosols at CM sections were a mix of freshly generated and those from main drifts. Low ambient concentrations and personal exposures suggest effective control strategies, with further reductions possible by curbing emissions from high-emitting light-duty vehicles.

Mar 16, 2022

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

By David Sprott, Patrick Andrieux

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commercial computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1991

By George W. Maynard

IN the course of an examination of some of the California hydraulie mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made tip of cement gravel, which resists the action of water, and can only be loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. DR. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880

By K. M. Deen, E. Asselin

Hydrometallurgical processes, i.e., Cu extraction from a mineral concentrate and Zn electrowinning, are coupled in a battery-like system. A naturally-sourced CuFeS2 concentrate mixed with activated carbon is used as a positive slurry electrode separated by a membrane from the negative compartment. The Zn is deposited on the negative Al current collector from the circulating solution containing 100 g L–1 Zn2+ in 0.2 M H2SO4. In this battery-like system, both CuFeS2 oxidation and Zn deposition are possible during the charging cycle. The additional benefit of this setup is the energy storage if discharged by re-dissolving the Zn in the negative compartment. Cyclic charge/discharge testing revealed oxidation of the mineral concentrate supported by the Zn2+/Zn redox reaction. The coulombic and energy efficiencies increased monotonically to 95.6% and 43%, respectively, with approximately 7% Cu extraction during the first 10 charge/discharge cycles (completed in 2.4 hours). The discharge energy density also increased from 2.7 to 36.2 mWh L–1. In the following 90 cycles, the low energy (~14%) and coulombic (~33%) efficiencies that were obtained confirmed the progress of irreversible reactions e.g. Cu extraction from the mineral concentrate. Overall, approximately 16% Cu was extracted from the mineral concentrate over 100 charge/discharge cycles (or about 12.2 hours). INTRODUCTION Chalcopyrite (CuFeS2) is the main economic copper-bearing mineral, which is generally processed through pyro-metallurgical methods to produce Cu. However, environmental challenges with smelting, depletion of high-grade ores and a large number of impurities (some toxic) have resulted in continued research aimed at the development of hydrometallurgical technologies to process CuFeS2. There are a number of different proposed hydrometallurgical routes in the literature to treat CuFeS2 concentrates, but only a few have attained commercial acceptance (Dreisinger, 2006). Zn is another commercially important metal that is mainly produced via acid leaching of roasted sphalerite (ZnS). The pregnant leach solution is rigorously purified to remove all the soluble metal impurities, particularly those that are electrochemically more noble than Zn and present large kinetic activity towards H2 evolution (Hu & Piron, 1992; Mackinnon, Brannen, & Fenn, 1987; Mureşan, Maurin, Oniciu, & Gaga, 1996). Metal impurities such as Cu, Co, Ni, Cd, Pb, Sb, As, Ge and Fe etc., if they exist in the leach liquor beyond the tolerance limits, can decrease the current efficiency during electrowinning and deteriorate the deposit quality (Alfantazi & Dreisinger, 2001). A complete flow sheet, describing the process steps of Zn metal production from mine site to pure metal is presented elsewhere (Brown, Meisenhelder, & Yao, 1983).

Jan 1, 2019

By George W. Maynard

In the course of an examination of some of the California hydraulic mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made rip of cement gravel, which resists the action of water, and can only he loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. Dr. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880

By A. Bouvard, N. Hoteit, E. Boidy, F. Pellet

In the context of the construction of an Underground Research Laboratory devoted to the feasibility studies of radioactive waste deposits, it appears of the utmost importance to study the long-term behaviour of rock, over a long time period. In this paper, some results of tests performed on the argillite from the Meuse-Haute-Marne site test in Eastern France are presented. Then a numerical simulation of one of this test using the viscoplastic damaging constitutive law proposed by Lemaitre is presented. Finally, this law is used to simulate numerically the behaviour of the rock at the wall of a circular tunnel in order to determine the extension and the change along the time of the Excavated Damaged Zone (EDZ). Advantages and limitations of the model are discussed. Dans le cadre de la réalisation d’un laboratoire de recherche souterrain conçu pour étudier la faisabilité d’installations de stockage de déchets radioactifs, il apparaît fondamental de caractériser non seulement le comportement viscoplastique à très long terme des matériaux mais aussi les phénomènes d’endommagement consécutif à la redistribution de contraintes provoquées par l’excavation des cavités. On présente ici les résultats d’essais réalisés sur les argilites du site de Meuse/Haute-Marne et destinés à caractériser leur comportement visco-endommageable. Il est ensuite procédé à une application de la loi viscoplastique endommageable de Lemaitre pour simuler l'un de ces tests. Les apports et les limites d'un tel modèle sont mis en évidence par des simulations numériques du comportement de la roche au pourtour d'une galerie circulaire permettant de suivre l’évolution au cours du temps de la zone endommagée (EDZ) à la paroi . Im Rahmen des Baus eines unterirdischen Forschungslabors für die Untersuchung der Machbarkeit von Deponien für radioaktive Abfälle erweist es sich als äußerst wichtig, das langfristige Verhalten von Gestein über einen langen Zeitraum zu untersuchen. Im vorliegenden Artikel werden einige Ergebnisse von Untersuchungen vorgestellt, die mit Tonschiefer aus der Meuse-Haute-Marne in Frankreich durchgeführt wurden. Anschließend wird eine numerische Simulation der Untersuchungen unter Verwendung des von Lemaitre vorgeschlagenen viskoplastischen Verformungsgesetzes vorgestellt. Schließlich wird dieses Gesetz auf die numerische Simulation eines Kreistunnels angewandt, um die Ausdehnung und die zeitliche Entwicklung der Auflockerungszone (EDZ) zu bestimmen. Es werden die Vorteile und Grenzen des Modells diskutiert.

Jan 1, 2003

By H. DeWitt Smith

THE mine operated by the United Verde Copper Co. is situated near Jerome, Ariz., on the eastern flank of the Black Hills, at an elevation of approximately 5500 ft. (1676 m.) above sea level. The mine and the town of Jerome are located on a steep hillside, which slopes rapidly to the valley of the Verde River. The smelter town of Clarkdale is situated in the Verde valley 4.1 mi. (6.5 km.) distant in an air line from Jerome, and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel & Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 mi. long and has a compensated 4 per cent. grade. At Clarkdale, it connects with the Verde Valley branch of the Santa Fe R. R. The narrow-gage (36-in.) line of the United Verde & Pacific Ry. was, until 1919, Jerome's only rail connection with a main trunk line. This road connects with a branch line of the Santa Fe system at Jerome Junction, after traversing 26 mi. of mountainous country. From the time of its location, in 1876, until its purchase by Senator W. A. Clark, of Montana, in 1889, the United Verde mine was worked on a small scale and shipments of high-grade gold-silver ore were made from the surface workings. Until 1894, when the narrow-gage railroad to

Jan 8, 1920

By Wm. R. Webster

This is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,' gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elcments present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 1, 1922

By Wm. R. Webster

This is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,' gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elcments present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 1, 1922

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area. Applications in the minerals industries include calcium carbonate, talc, barytes, mica, diatamaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc. The basic principles can be extended to provide continuous drying and delivery of discrete particles from a wet process slurry. The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques. Mean particle sizes in the order of 1 micron are achieveable from pre-milled feeds, or maintained from similar slurries in the drying mode. Aspects of feed preparation and multi-stage processing are discussed.

Jan 1, 1983