Search Documents

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By W E. Short

Ausmelt top submerged lance technology is at the cutting edge of technological developments in non-ferrous metal smelting with commercial operations throughout the world. The Technology is being used for lead smelting, copper smelting and matte converting, fuming zinc from slags, recycling iron residue from zinc plants, processing the aluminium industry hazardous waste SPL , precious metal processing, nickel-copper residue smelting and converting, and tin smelting. The Technology is also being developed for projects involving iron-making and waste industry opportunities. There are 19 furnaces operable or under design at the time of writing. The benefits to operators using Ausmelt Technology vary depending on application, but typically result from environmental improvements, enhanced recovery of valuable products, lower capital and operating costs, more flexible operations capable of handling a wide range of feed materials, better removal of impurities, or improved product quality. Growing industry acceptance of the Technology is evidenced by the fact that more than 20 per cent of the worldÆs tin production will be extracted in systems using Ausmelt Technology when the Yunnan Tin Corporation plant starts up in 2001. Metallurgists, industrialists and investors have accepted the Technology for improved operations in both greenfield main smelters and add-on plants in Korea, China, Japan, Germany, Peru, Zimbabwe, India, Namibia and Australia. Ausmelt intends that this paper will update the industry by outlining recent achievements of the Technology in global metallurgical operations.

Jan 1, 2000

By C A. Heinrich, J L. Walshe, V J. Wall

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982

By Edwin Ludlow

THERE has been so much misinformation sent out through the newspapers, and I find so few people who are really acquainted with the true facts in regard to the coal strike, that I feel it would be advan-tageous to present the facts as I have been able to gather them. One of the great points that the miners are now mak-ing is the fact that the operators of the central competi-tive field, consisting of the states of Illinois, Indiana, Ohio and Pennsylvania, have refused to meet them in a joint conference such as has been customary in previous years. There are two reasons why the operators de-clined to hold such a meeting. In the first place, the last time they held a meeting of this kind they were all indicted under the Sherman Act for making an agree-ment in restraint of trade. In the second place, the miners at their convention did not authorize their dele-gates to negotiate a new contract, but instructed them that nothing less than a scale based on the present wage, with the addition that there should be a six-hour day, a five-clay week, time j and a half for over time, and double time for Sundays, would be accepted. These additions would very much increase the cost of coal over the present wage scale. The operators could not consider renewing a contract on the present scale, as it would mean ruin for them, and as the miners were not authorized to negotiate a new scale on a fair basis that would enable the operators to mine coal in competi¬tion, with the open-shop mines the operators did not feel that there was any use in meeting the delegates. Thirty per cent. of the output of bituminous coal comes from the open-shop mines of West Virginia, Alabama and Pennsylvania. During the strike, in 1919, this 30 per cent. was increased to 50 per cent. and it has affected the operations of the union mines to such an extent this year that they have been able to run only 15 to 30 per cent. of their time, while the open shop mines have run from 60 to 80 per cent. as the wages in these mines had been reduced to the 1917 scale.

Jan 5, 1922

By Jan L. Reichelderfer, Thomas L. Richardson

Completion of the H-3 Highway Tunnel Project was a critical element in opening this award winning project. The exploratory tunnel was completed as a maintenance tunnel and included difficult shafts extending into the main tunnel cross passages. The project also involved a major addition to the traffic operations center including a deep excavation in close proximity to the tunnel portal structures. The projects also included various completions and improvements to the main tunnels, such as paving, drainage, maintenance, and a variety of critical life-safety issues, such as radio systems, telephones, etc. The highway opened in December 1997.

Jan 1, 2001

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By W. J. Rude

LARGEST of the known commercial deposits of pebble phosphate are those found in Polk County, Florida. The phosphate bed, commonly known as the matrix, will consistently average 6 to 9 ft. in depth, and is found under 3 to 60 ft. of over-burden. The phosphate pebbles, white and black in color, varying greatly in grade, are found imbedded in a matrix of sand and clay; and range in size from the fines to pebbles 1 1/2 in. in diameter, although the average coarse size is approximately 1/2 in. in diam¬eter. On some of the washers all material under 14 mesh is lost. High-grade phosphate (75 per cent plus of bone phosphate of lime, CasP2Oa) is generally soft, the pebbles breaking up during the mining operation and in pumping; low-grade phosphate, 67 to 69 B.P.L., is black in color with hard pebbles with no loss encountered in pumping.

Jan 1, 1941

By William D. Cassity, Batric Pesic

Introduction Gold mining on an industrial scale is becoming increasingly dependent on low-grade refractory sulfide ores that contain large amounts of pyrite (FeS2) and arsenopyrite (FeAsS). Gold is usually present as sub-microscopic particles dispersed evenly throughout the sulfide matrix. Without some form of preoxidation, efficient recovery of this finely disseminated gold through cyanide leaching is hampered because the surface of the sulfide particle becomes passivated and impervious to penetration of the cyanide. Traditional methods for recovery of refractory gold from arsenopyrite ores include roasting and autoclave leaching. A modem alternative method is to preoxidize the mineral using the bacterium Thiobacillus ferrooxidans prior to attempting to re- cover the gold through cyanidation. The bioleaching of arsenopyrite ores presents a problem in the mobilization of large quantities of arsenic, present both in the +5 and +3 ionic states. Dissolved arsenic species pose a dual problem: they are -1 to the bioleaching process itself through inhibition of bacterial activity, and they also pose an environmental threat. The arsenate anion (AsO2) has been shown to be more toxic to living organisms, including Thiobacillus ferrooxidans, than the arsenate anion (AsO43) (Collinet and Morin, 1989). There is some disagreement as to the fate of arsenite in bioleaching solution. Mandl, Matulova, and Docekalova (1992) reported that dissolved arsenite concentration was constant during a long-term bioleaching study of chalcopyrite using Thiobacillus ferrooxidans. Torma and Oolman (1992) report that Thiobacillus ferrooxidans has been found capable of oxidizing As3+ to As5+. The solid products of arsenopyrite/pyrite bioleaching include jarosite (MFe3(SO4)2(OH)6 where M can be K+, Na+, NH4+ or H3O+), scorodite (FeAsO4.2H2O), ferric hydroxides, and ferric hydroxysufites (Carlson et. al., 1992; Van Breemen, 1982; Lazaroff et. al., 1982). The particular species formed is a function mainly of pH. Little study has been performed on the effect of solid products on bioleaching. Pesic and Kim (1993) showed that Thiobacillus ferrooridans cells served as a nucleation sites for jarosite particles, which grew rapidly and eventually killed the cell. Most bioleaching studies are performed at low pH&apos;s (<2.0) under uncontrolled conditions. By studying bioleaching of arsenopyrite under controlled pH conditions and at higher pH&apos;s (2.0 to 3.0), the distribution of iron and arsenic between the solid and liquid phases can be controlled, and their effects studied. The objective is to develop a bioleaching process that operates at high efficiency while keeping amounts of dissolved heavy metals low. Pesic, Stohok, and Torma (1993) demonstrated the usefulness of this approach in the leaching of cobaltite (CoAsS) concentrates. Materials and Methods The focus of this study was the bioleaching of arsenopyrite ore by Thiobacillus ferrooxidans. The parameters studied included the effects of pH, and the effects of arsenate (AsO43 and arsenite (AsO2). pH studies included pH set initially but not controlled, and pH controlled continuously with NaOH or LiOH. Bioleaching results from two strains of Thiobacillus ferrooxidans with different adaptation histories were compared. Bioleaching experiments were conducted in 150 ml stirred glass reactors using a strain of Thiobacillus ferrooxidans adapted to arsenopyrite ore, supplied by the U.S. Bureau of Mines. These bioreactors were innoculated with stock cells grown on arsenopyrite ore for 14-16 days. Typical elemental breakdown for this ore was: As, 9.90%; Fe, 18.60%, Stot, 9.26%; Suifide, 7.50%; SiO2, 25.90%. Mineralogically, the ore contained both arsenopyrite and pyrite. Bioleaching efficiency was measured by withdrawing bioleach solution samples at selected intervals, filtering, and measuring the amount of dissolved cobalt, iron, and arsenic by atomic absorption spectroscopy. Because the precipitation of iron and arsenic at higher pH&apos;s would lead to unreliable results, a 100 mg tracer of cobaltite concentrate from the Blackbird mine in southern Idaho was added to solution. Dissolution of the cobaltite tracer was used to indicate bioleaching of the bulk arsenopyrite ore. Cobalt has been shown to be stable in solution even when iron and arsenic were precipitated (Pesic, Storhok, and Tonna, 1993). The pa-

Jan 1, 1995

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995

By D. R. George

Preliminary research has identified several organic and aqueous solutions that are effective absorbents for SO, from simulated smelter gas containing 0.3 to 2% SO2. These SO2 loaded solutions are also compatible to the reaction of H2S and SO2 to precipitate a readily filtered elemental sulfur. The economic removal of SO2 and production of elemental sulfur from stack gases discharged by base- metal smelters is a challenging goal. The magnitude of this task is illustrated by the estimate that about 3.5 million tons of SO2 are discharged to the atmosphere by smelters annually in the U.S. The SO2 concentration of the gases ranges from about 0.5 to more than 3%. As the sulfur content of SO2 is 50% a potential production of 1,750,000 tons of sulfur per year is indicated.

Jan 1, 1970

By Benoit Gagnon

Mining of the Schefferville iron deposits began in 1954 on completion of the 574 km railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950&apos;s, testwork began at Schefferville to develop a process for upgrading the extensive lower grade deposits containing 5l% iron with 15% silica (natural analysis). Engineering for 6.1 million tons per year Beneficiation Plant using cationic silica flotation and the A-C Grate kiln began in 1970 and the first pellets were produced in mid 1973. Production requirements and operating difficulties have restricted capacity to approximately 85% of design but ongoing improvements are being made continuously to attain design capacity.

Jan 1, 1980

"The Merensky Reef is a platinum group minerals (PGM) bearing reef in the Bushveld Igneous Complex in South Africa. The reef has been treated by bulk PGM and sulphide flotation with the aim of maximisingthe valuable minerals recovery and gangue minerals rejection.Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained were compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis.The results obtained on 1:1 pentlandite-pyroxene mixtures showed that the quality of process water plays an important role in flotation. The flotation recoveries of pentlandite and pyroxene were lower in synthetic process water compared to those obtained in a simple electrolyte solution."

Jan 1, 2003

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By E. Hornbogen

The deformation mechanisms of a iron-phosphorus alloys were compared at 20oand —196°C. Alloying with phosphorus increases the resistance to slip, but has little effect on the resistance to twinning. The stress for onset of twinning is nearly independent of temperature, but there is an increasing tendency for cleavage along (112) twin boundaries with decreasing temperature and increasing phosphorus content. FIVE iron-phosphorus alloys and one high-purity iron (0.004 pct C, 0.004 pct N, 0.05 pct O) were vacuum melted and cast, then homogenized for 6 hr at 1100oC and water-quenched. Single crystals were cleaved from the coarse grains produced in this manner. The hardness was measured* on polished (100) surfaces of the crystals at 20" and -196°C. Laue back-reflection patterns indicated a deviation of not more than 3 deg from coincidence of the {100} plane with the surface. The deformation mechanisms were studied by relief effects on the polished surfaces. Yield points in compression (0.5 pct offset) were measured with polycrystalline material. At 20°C the addition of phosphorus to a iron leads to a change from slip to twinning as the main deformation mechanism, Figs. 1(a), (b). Between 2 and 4 at. pct P slip and twinning occur simultaneously. In alloys with more than 4 at. pct P twinning is the main deformation mechanism and slip was observed only in the neighborhood of twin intersections. All cracks at 20oC were on (100) planes, some initiated by twins.&apos; From measurements made at-196oC, hardness and yield points of all the alloys were nearly constant and the same as the hardness of high phosphorus alloys that deformed by twinning at 20°C, Figs. 2 and 3. In the high-purity iron, plastic deformation at -196°C occurred by both slip and twinning, but deformation in the iron-phosphorus alloys appeared to be entirely by twinning. In the high phosphorus alloys a large number of cracks formed along the (112) twin boundaries and at intersections of twins, in addition to the (100) cleavage, Fig. 1(c). DISCUSSION In , iron, plastic deformation can occur either by slip or by twinning, depending upon composition,

Jan 1, 1961