Search Documents

By Khosrow Bakhtar

A series of nineteen shear tests were performed on fractures 1 m2 in area, generated in blocks of sandstone, granite, tuff, hydro- stone and concrete. The tests were conducted under quasi-static and dynamic loading conditions. A vertical stress assisted fracturing technique was developed to create the fractures through the large test blocks. Prior to testing, the fractured surface of each block was characterized using the Barton JRC-JCS concept. The results of characterization were used to generate the peak strength envelope for each fractured surface. Attempts were made to model the stress path based on the classical transformation equations which assumes a theoretical plane, elastic isotropic properties, and therefore no slip. However, this approach gave rise to a stress path passing above the strength envelope which is clearly unacceptable. The results of the experimental investigations indicated that actual stress path is affected by the dilatancy due to fracture roughness, as well as by the side friction imposed by the boundary conditions. By introducing the corrections due to the dilation and boundary conditions into the stress transformation equation, the fully corrected stress paths for predicting the strength of fractured blocks were obtained.

Jan 1, 1984

By Satyajit Vaidya, Rudolph Frizzi, Quadri Owokoniran

"This paper presents a case history in the design and construction of high-capacity drilled shafts for the iconic New York Wheel presently being constructed along the St. George area waterfront in northern Staten Island, New York. Although the site is located in an area that offers views of the Statue of Liberty, the Manhattan skyline, and New York Harbor, the variable and challenging subsurface conditions at the site and the structural loading requirements for Wheel erection and service conditions presented geotechnical design and construction challenges. The paper focuses on site and subsurface conditions, drilled shaft design and construction details, results of Osterberg-cell and lateral load testing, and load test data analysis and evaluation.PROJECT DESCRIPTIONThe proposed 630-foot (190 m) -tall New York Wheel (the Wheel) is projected to be one of the tallest observation wheels in the world. Upon completion, the Wheel will be capable of carrying over 1,400 passengers in its 36 capsules. The Wheel site is located along New York Harbor offering views of the Statue of Liberty, the Manhattan skyline, and the New York Harbor; see Fig. 1. The Wheel structure is sited along the waterfront, and served by a 3-story terminal located south of the Wheel in the eastern portion of the site and having a footprint area of about 34,250 sq-ft (3,180 sq-m). A 4-story parking Garage, with a footprint of about 112,840 sq-ft (10,480 sqm), is to be constructed south of the Wheel in the central and western portions of the site.SITE AND SUBSURFACE CONDITIONSThe site’s close proximity to the New York Harbor presented geotechnical challenges because the site is located in an area that was once beyond the historic shoreline of Staten Island. The site is an about 350,000-sq-ft (32,500-sq-m) parcel generally bounded by the Richmond County Bank Ballpark to the southeast, the 9-11 Memorial to the east, Bank Street to the north and northeast, and Richmond Terrace and an associated retaining wall to the southwest and south. A 50-ft (15-m) -wide New York City Transit Easement, with an active on-grade service area and tracks, is located in the southern portion of the site. See Fig. 2 for site location and approximate location of the Wheel foundation footprint."

Jan 1, 2016

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By Mary Stewart, Jim G. Petrie, Geoff Brent

"Life Cycle Assessment (LCA) is gaining increasing acceptance as a decision-support tool by which to evaluate the environmental performance of a product, process or service. This is evidenced by its inclusion in international policy documents (for example in the European Union’s Integrated Product Policy) and in environmental management standards (the ISO 14 040 series of environmental management codes relate to LCA). In response to this, the minerals industry has conducted a number of commodity-specific LCAs. These include studies for global production of a number of commodities including copper, nickel, aluminium and steel. In addition, a number of minerals companies profess to use LCA as part of their suite of project and technology assessment tools. Often, this collected use represents more a situation of “we do this because we’re told it’s good for business” rather than from any demonstrable evidence of this fact. This has led to a situation of much confusion and disillusionment within the industry, exacerbated by the obvious current limitations of LCA to accurately reflect the environmental performance of minerals and metals.Our point of departure here is that LCA, conforming as it does to the tenets of environmental systems analysis, is a valuable starting point, and that there is merit in exploring to what extent the methodology can be enhanced to better reflect the environmental performance of minerals and metals. Specifically, we explore here the further development of LCA to address the following:• Land Use issues• Consumption of Abiotic Resources including metallic and non-metallic minerals, water and soil)• Human and Eco-toxicity issues relating to mobility and bio-availability of metals• Salinityand address these through selected experimental and simulation case studies relating to energy- and base minerals production. Advances resulting from the United Nations Environment Programme/Society for Environmental Toxicology and Chemistry Life Cycle Initiative are presented in that they directly affect the application of LCA to mining, minerals and metals. Comments are offered on how best the mining and minerals industry might interface with future developments resulting from this Initiative in order that the Initiative can deliver outcomes which render LCA a useful tool for decision making in mining and minerals processing."

Jan 1, 2003

By Rick Hyndman

? Context: Ø Global action on climate change ? The situation of trade-exposed industry sectors ? The federal government?s draft plan for industry ? CAPP?s position ? Canadian emissions & Canada?s Kyoto target Simple Economic Theory of Dealing with Externalities ? Put cost on emissions Ø Carbon tax Ø Emission trading with auctioned permits ? GHG costs get reflected in the prices of energy alternatives, goods & services Ø Decisions driven by changes in relative prices ? Switching to lower emission fuels ? More energy efficient ways of producing ? More energy efficient appliances, cars, housing ? Reduced demand for energy intensive goods & services ? Anticipation of higher CO2 price drives low CO2 technology Development

Nov 1, 2002

By John W. Gunnett

The purpose of this afternoon’s presentation is to highlight the investigative proce dures employed to complete an engineering audit of a mining operation. Skelly and Loy has been retained to perform operational audits throughout the nation’s coal fields, The need for such studies is generally associated with long term coal supply contracts and is typically initiated by the utility company. However, a number of projects have been commissioned by mining companies while others have been jointly funded by the utility and mining company.

Jan 1, 1992

By L. A. Ruth

Vision 21 is a government/industry/academia cost-shared partnership to develop the technology basis for integrated energy plants that will, early in the 21stcentury, result in the deployment of ultra-clean plants that produce electricity and “opportunity” products. Vision 21 plants will use fossil fuel feed-stocks in combination with other domestic resources, e.g., biomass, municipal waste, and petroleum coke. Opportunity products could include transportation fuels, steam, high-value chemicals, synthesis gas, and hydrogen. Performance targets for Vision 21 plants, example plant configurations, and the key technologies that will be needed are described.

Jan 1, 2000

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By W. W. Simpson, W. L. Staker, R. G. Sandberg

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 17 kg NaCN/t of solution (0.34 lb NaCN/st). Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5-2.9 kg CaS/kg Hg (0.5-2.9 lb/lb) in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1985

By R. Farnfield, W. Birch

Arguably, some of the most restrictive statutory blast vibration requirements attached to mineral extraction operations can be found in the United Kingdom. Such limitations are, as a rule for the UK, stipulated together with a required statistical confidence that has to be observed in the blast design process in order to ensure total planning compliance. A key element in this procedure is the effect imparted by vibration data scatter from previous blasts as this becomes reflected in the site’s operational standard error statistic and in turn directly influences the maximum instantaneous charge weights that can be justifiably employed. The greater the scatter, the lower the compliant charge weights become.

Jan 1, 2006

By K. E. Laughery

The Nevada Barite industry has experienced a 277% growth over the last five years with a total production of 2,542,000 tons. Total production prior to 1970 approximates 2,700,000 tons dating back to 1907 Annual production, as can be seen in Table 1, has increased from 192,000 tons in 1971 to 723,000 tons in 1975. During this same period U.S production has increased from 825,000 tons to 1,056,000 tons. Nevada is now the leading producer with 69% of the market. The increase in the Nevada barite production is, of course, directly related to the increased demand for weight material coupled with the lack of other sources and the relative economic advantage of the Nevada barite, A significant tonnage of Nevada barite is utilized in the non-oil well market, principally at FMC's barite chemical plant at Modesto, California; however the growth has been in the oil well market.

Jan 1, 1976

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By R. L. Orr, O. D. Sherby, J. E. Dorn

Creep data for pure metals at temperatures above those at which rapid recovery occurs (above about 0.45 the melting temperature) are correlatable by means of the equations and These correlations were applied successfully to data for aluminum, iron, nickel, copper, zinc, platinum, gold, and lead as well as for simple alloys. For a given metal, AH is a constant about equal to the activation energy for self-diffusion. THE early recognition that creep is stimulated by thermal activation prompted numerous investigators', ' to apply the same laws that are valid for the viscous behavior of liquids to analyses of creep data. To a good first approximation these laws are summarized by the equation were i is the creep rate; T, the absolute temperature; R, the gas constant in cal per degree per mol; T, the applied stress; AH, the activation energy in cal per mol; S', a constant dependent on the entropy of activation, the frequency of activation, and the contribution of each activation to the strain; and B', a constant dependent upon the size of the flow unit that is activated. Although Eq. 1 describes the flow of viscous fluids very accurately, its application to the creep of solids has been disappointing. Two reasons for the failure of Eq. 1 for creep are now known: First, the decelerating creep rates during primary creep demand that the internal structures of the metals are changing and that these changes might be reflected by changes in one or more of the three creep parameters S', AH, and B'. Consequently when the conventional methods of evaluating these parameters are employed by comparing the secondary creep rates at a series of temperatures and at a series of stresses, the true effects of temperature and stress are masked because of simultaneous changes in one or more of the creep parameters. Second, as will be illustrated more fully later, three distinctly different types of investigations have shown that the stress term for high temperature creep enters the analysis as and not as t/T. This rather unexpected result points sharply to a significant fundamental difference between the mechanisms for the viscous behavior of fluids and the high temperature creep of metals. More recent extensive investigations",'4 on the creep of high purity aluminum and several of its dilute a solid solutions have shown that where E is the total creep strain; temperature compensated time = for a constant temperature test; t, is the initial stress in a constant load test or the constant true stress in a constant stress test;" and t is the duration of test. • Eq. 2 is valid for either constant stress or constant load tests; but the total creep curve is difierent (i.e. the function, f, is differentl for each test. The fundamental origin of the validity of Eq. 2 is thought to arise from some equivalence of substructures in constant load creep tests at equal values of 0 or E. Both X-ray and metallographic examination revealed that practically identical lattice distortions and subgrain sizes are obtained for the same creep strain under the same load over wide ranges of test temperature.' Furthermore the room temperature tensile properties following equal creep strains at different temperatures under constant loads were also identical, illustrating that identical substructures were indeed obtained.' " A second type of correlation was obtained by differentiating Eq. 2 with respect to time, giving For the secondary creep rate, denoted by i,, But Eq. 2 reveals that 0, is a function of a, alone because the secondary creep rate in a given constant load test is always reached at a fixed value E,". Therefore where is the function that was introduced a number of years ago by Zener and Hollomon." Eq. 4 is not only valid for creep but will permit correlations between constant load creep and tensile data where e, is the rate of tensile straining and (TC is the engineering ultimate tensile strength.

Jan 1, 1955

By A. L. Murray

"Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years, and in most mining towns of the state, both the operators and their employees deserve much credit for the efforts put forth to better the living, working, educational and recreational conditions. Progress has been and is being made, but there are still a few important towns where purer water and better sewage disposal are pressing needs.In the older metal-mining towns that are incorporated and are independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking toward improved welfare conditions than in company towns controlled by the mine operators.However, even in such towns the companies can do much to better welfare conditions, as shown by the progress in Bingham Canyon during the past several years. The Utah Copper Company has spent $800,000 since 1920, in the erection of modern brick cottages, apartment houses and the Germnell Memorial Club. The cottages and apartment houses have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club erected and equipped at a cost of $175,000 was provided by the company for the benefit of the Utah Copper employees living in the canyon and has been made the recreational center for the camp. Another improvement is the $100,000 fireproof hotel built by the United States Mine of the United States Mining, Smelting and Refining; Co. in the Copperfield section of Bingham Canyon. This hotel will accommodate 105 men exclusive of hotel help and has all the conveniences of a city hotel."

Sep 1, 1925

By Dale S. Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was fi rst attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The confi guration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the fi rst four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition. A computer simulation of the above explosive destruction scenario was completed using the computer hydrocode AUTODYN with a granular material model to treat the soil and the RHT brittle material model to represent the concrete. AUTODYN accurately recreated the scenario including the slightly damaged response of the concrete structure to the initial four charges and the collapse of the structure resulting from the second single charge close to the roof.

Jan 1, 2007

The building is a lofty, well-ventilated one of hardwood frame, with galvanized-iron walls and roof, and consists of five spans running north and south, covering a total length of 236 ft. Each span is composed of nine bays of 1:3-ft. centres, making the total width of the building 117 ft. The refinery is situated conveniently at a distance of 100 yds from the smelters. Through the third span of the building runs a 5-ton electric overhead travelling crane, of a 3-motor type, with a span of 29 ft. The crane runway extends over a railway line, which connects the smelters to the refinery. This crane is llsed for handling bullion, coal, melting kettles, lead pumps, &c. A 3-ton crane of similar type, but with a 50-ft. span, runs through the fifth span of the building and also extends over the railwav line alreadv mentioned. This crane is used to load the soft lead into railway trucks, or to stack lead awaiting shipment in the area covered by the crane's operations.

Jan 1, 1918

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By Benjamin W. Haynes

This Bureau of Mines publication comprises a compilation of the state of the science in Pacific Ocean manganese nodule mineralogy and elermental composition. The report is divided into three sections: morphology, mineralogy and elemental composition. The nodule morphology section defines what is considered a nodule for the study, and details the external characteristics and internal structure. Nodule mineralogy is discussed in three sections: manganese minerals, iron oxide minerals, and accessory minerals. The major manganese minerals discussed are todorokite, birnessite, and vernadite. The iron oxide minerals are less well known and include feroxyhyte, goethite, and lepidocrocite. Accessory minerals present include quartz, clays, and other silicates and nonsilicates. A discussion on moisture content is also included. The elemental composition section presents data on 74 elements occurring as cations or anions. Summary data, histograms, and interelement correlation coefficients are presented. The elements are grouped as follows: major and minor elements of potential economic interest (8), other major and minor elements (9), elements of environmental interest (8), rare-earth elements (15), precious-metal-group elements (6), radioactive elements (3), other trace elements (17), and anion-forming elements (8). Cross sectional determinations of Ni, Cu, Zn, Co, Pb, Fe, Ce, and Ba are given for a single nodule to show the general tendency of different growth patterns within a nodule because of different element associations and composition.

Jan 1, 1982

By Robert B. Parsons

"It is generally felt that flow-through shares face a bleak future under the set of tax rules proposed in the federal government's tax reform white paper. Industry and government circles are beginning to give thought to alternatives to flow through as a mechanism for facilitating equity financing in the exploration industry. Despite suggestions that grants and tax credits may someday be on the table, industry is sticking to its position that there is no substitute for flow-through. Alternatives toFlow-throughProposals in the federal government's tax reform white paper have cast significant doubt on the ability of the mining industry to raise risk capital after 1989by way of flow-through shares. There is serious concern that introduction of the ""cumulative net investment loss"" (CNIL) rules, the phase-out of the mining explorati0! 1 depletion allowance (MEDA), and the Increased capital gains inclusion (750/0 versus 50%, at present) will make the economics of flow-through so unattractive after 1989 that these shares will hold little appeal to most investors. The question might be raised, then, as to what alternatives exist by way of tax or other government assistance that could help the exploration sector.The purpose of this paper is to survey the types of government incentives that could be of some value to explorationists and to the mining industry in general. For the past several years, flow-through has been in the spotlight insofar as incentives to the exploration industry are concerned. Other potentially useful and attractive incentives have been partially hidden in the shadow of flow-through. These incentives, in certain circumstances, can be of considerable benefit, and should not be ignored."

Jan 1, 1988